Export limit exceeded: 374967 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (374967 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-68356 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: watchdog: airoha: Prevent division by zero when clock frequency is zero clk_get_rate() can return 0 when the clock provider is not properly configured or the clock is unmanaged. The driver uses wdt_freq as a divisor directly in airoha_wdt_probe() to compute max_timeout and in airoha_wdt_get_timeleft() to compute the remaining time, which results in a division by zero. Add a check for wdt_freq == 0 in probe and return -EINVAL with dev_err_probe() to prevent the division by zero and provide a diagnostic message. | ||||
| CVE-2026-68355 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: wifi: ath11k: fix potential buffer underflow in ath11k_hal_rx_msdu_list_get() When the first entry in msdu_details has a zero buffer address, the code accesses msdu_details[i - 1] with i == 0, causing a buffer underflow. Fix similarly to ath12k_wifi7_hal_rx_msdu_list_get() by adding a separate check for i == 0 before the main condition to prevent the out-of-bounds access. Found by Linux Verification Center (linuxtesting.org) with SVACE. | ||||
| CVE-2026-68354 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: firewire: net: Fix fragmented datagram reassembly fwnet_frag_new() keeps a sorted list of received fragments for a partial datagram. When a new fragment is adjacent to an existing fragment, the code checks whether the new fragment also closes the gap to the next or previous list entry. Those neighbor lookups currently assume that the current fragment always has a real next or previous fragment. At a list edge, the next or previous entry is the list head, not a struct fwnet_fragment_info. The gap checks also compare against the old edge of the current fragment instead of the edge after adding the new fragment. As a result, a fragment that bridges two existing ranges may leave two adjacent ranges unmerged, so fwnet_pd_is_complete() can miss a complete datagram. Check for the list head before looking up the neighboring fragment, and compare the neighbor against the new fragment's far edge when deciding whether to merge all three ranges. This issue was found by a static analysis checker and confirmed by manual source review. | ||||
| CVE-2026-68353 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: wifi: ath6kl: fix OOB read from firmware num_msg in TX complete handler The firmware-controlled num_msg field (u8, 0-255) drives the loop in ath6kl_wmi_tx_complete_event_rx() without validation against the buffer length. This allows out-of-bounds reads of up to 1020 bytes past the WMI event buffer when the firmware sends an inflated num_msg. Add a check that the buffer is large enough to hold the fixed struct and the num_msg variable-length entries. | ||||
| CVE-2026-68352 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: wifi: ath6kl: fix OOB read from firmware IE lengths in connect event The firmware-controlled beacon_ie_len, assoc_req_len, and assoc_resp_len fields in ath6kl_wmi_connect_event_rx() are not validated against the buffer length. Their sum (up to 765) can exceed the actual WMI event data, causing out-of-bounds reads during IE parsing and state corruption of wmi->is_wmm_enabled. Add a check that the total IE length fits within the buffer. | ||||
| CVE-2026-68351 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: wifi: carl9170: bound memcpy length in cmd callback to prevent OOB read When the firmware sends a command response with a length mismatch, carl9170_cmd_callback() logs the mismatch and calls carl9170_restart() but then falls through to memcpy(ar->readbuf, buffer + 4, len - 4). Since len comes from the firmware and can exceed ar->readlen, this copies more data than the readbuf was allocated for. Bound the memcpy to min(len - 4, ar->readlen) so that the response is still completed -- avoiding repeated restarts from queued garbage -- while preventing an overread past the response buffer. | ||||
| CVE-2026-68350 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: wifi: carl9170: fix OOB read from off-by-two in TX status handler The bounds check in carl9170_tx_process_status() uses `i > ((cmd->hdr.len / 2) + 1)` which is off by two, allowing 2 extra iterations past valid _tx_status entries when the firmware- controlled hdr.ext exceeds hdr.len/2. Fix by using the correct comparison `i >= (cmd->hdr.len / 2)`. | ||||
| CVE-2026-68349 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: wifi: carl9170: fix buffer overflow in rx_stream failover path The failover continuation in carl9170_rx_stream() copies the full tlen from the second USB transfer instead of capping at rx_failover_missing bytes. When both transfers are near maximum size, the total exceeds the 65535-byte failover SKB, triggering skb_over_panic. Limit the copy size to the missing byte count. [Fix checkpatch CHECK:PARENTHESIS_ALIGNMENT] | ||||
| CVE-2026-68348 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ASoC: tas2781: bound firmware description string parsing The TAS2781 firmware parser reads several variable-length description strings with strlen() before checking that the string terminator is present inside the firmware blob. A malformed firmware image without a NUL terminator can therefore make the parser walk past the end of the firmware buffer before the later size checks run. Add a small bounded string-length helper and use it for all description fields that are parsed from the firmware buffer. Keep the existing size checks for the fixed bytes that follow each string. | ||||
| CVE-2026-68347 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: iommu/amd: Fix IRQ unsafe locking in gdom allocation Lockdep complains: [ 259.410489] ===================================================== [ 259.417287] WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected [ 259.424667] 7.0.0-g51db1d8d2113 #54 Not tainted [ 259.429718] ----------------------------------------------------- [ 259.436516] qemu-system-x86/10143 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire: [ 259.444670] ff3b2b1c60305170 (&xa->xa_lock#25){+.+.}-{3:3}, at: __domain_flush_pages+0x17c/0x4b0 [ 259.454485] and this task is already holding: [ 259.460991] ff3b2b1c98504cc0 (&domain->lock){-.-.}-{3:3}, at: amd_iommu_iotlb_sync+0x25/0x60 [ 259.470408] which would create a new lock dependency: [ 259.476041] (&domain->lock){-.-.}-{3:3} -> (&xa->xa_lock#25){+.+.}-{3:3} [ 259.483615] but this new dependency connects a HARDIRQ-irq-safe lock: [ 259.492447] (&domain->lock){-.-.}-{3:3} [ 259.492449] ... which became HARDIRQ-irq-safe at: [ 259.503705] lock_acquire+0xb6/0x2e0 [ 259.507790] _raw_spin_lock_irqsave+0x3e/0x60 [ 259.512748] amd_iommu_flush_iotlb_all+0x20/0x50 [ 259.517996] iommu_dma_free_iova.isra.0+0x1b8/0x1e0 [ 259.523534] __iommu_dma_unmap+0xc2/0x140 [ 259.528100] iommu_dma_unmap_phys+0x55/0xc0 [ 259.532863] dma_unmap_phys+0x274/0x2e0 [ 259.537238] dma_unmap_page_attrs+0x17/0x30 [ 259.542000] nvme_unmap_data+0x13e/0x280 [ 259.546473] nvme_pci_complete_batch+0x45/0x70 [ 259.551524] nvme_irq+0x83/0x90 [ 259.555123] __handle_irq_event_percpu+0x92/0x360 [ 259.560466] handle_irq_event+0x39/0x80 [ 259.564841] handle_edge_irq+0xb2/0x1a0 [ 259.569214] __common_interrupt+0x4e/0x130 [ 259.573882] common_interrupt+0x88/0xa0 [ 259.578256] asm_common_interrupt+0x27/0x40 [ 259.583019] cpuidle_enter_state+0x119/0x5d0 [ 259.587877] cpuidle_enter+0x2e/0x50 [ 259.591962] do_idle+0x153/0x2c0 [ 259.595657] cpu_startup_entry+0x29/0x30 [ 259.600128] start_secondary+0x118/0x150 [ 259.604601] common_startup_64+0x13e/0x141 [ 259.609266] to a HARDIRQ-irq-unsafe lock: [ 259.615384] (&xa->xa_lock#25){+.+.}-{3:3} [ 259.615386] ... which became HARDIRQ-irq-unsafe at: [ 259.627039] ... [ 259.627039] lock_acquire+0xb6/0x2e0 [ 259.633071] _raw_spin_lock+0x2f/0x50 [ 259.637250] amd_iommu_alloc_domain_nested+0x140/0x3c0 [ 259.643078] iommufd_hwpt_alloc+0x272/0x800 [iommufd] [ 259.648813] iommufd_fops_ioctl+0x14e/0x200 [iommufd] [ 259.654547] __x64_sys_ioctl+0x9d/0xf0 ... Since amd_iommu_domain_flush_pages() necessarily holds domain->lock to do the flush, switch the allocation side in gdom_info_load_or_alloc_locked() to HARDIRQ-safe allocation. The IOMMU_DESTROY->free path has the same issue, so switch that path to HARDIRQ-safe locking as well. | ||||
| CVE-2026-68346 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ALSA: hda: cs35l41: validate and free ACPI mute object cs35l41_get_acpi_mute_state() evaluates a _DSM method to get the ACPI mute state and reads the first byte from the returned object. However, the returned ACPI object is owned by the caller and is never freed after use, so each successful query leaks the _DSM result object. The code also assumes that the returned object is a buffer with at least one byte. A malformed firmware response can return a different object type or an empty buffer, and the direct ret->buffer.pointer dereference can then access an invalid pointer. Use the typed _DSM helper, validate that the returned buffer contains at least one byte, and free the ACPI object after reading it. | ||||
| CVE-2026-68345 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: arm_mpam: guard MBWU state before adding it to garbage __destroy_component_cfg() adds each RIS mbwu_state object to the MPAM garbage list when destroying component configuration. However, mbwu_state is allocated per RIS and only for RISes with MBWU monitors. A component can therefore have comp->cfg allocated while some RISes still have ris->mbwu_state set to NULL. Passing a NULL mbwu_state to add_to_garbage() dereferences the NULL pointer inside the macro. Skip RISes that do not have an mbwu_state object before adding them to the garbage list. | ||||
| CVE-2026-68344 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: usb: atm: ueagle-atm: reject descriptors that confuse probe and disconnect uea_probe() distinguishes a pre-firmware device from a post-firmware one using the USB id (UEA_IS_PREFIRM()), and stores a different object as the interface data in each case: a 'struct completion' for a pre-firmware device (to be waited on in .disconnect()), or a 'struct usbatm_data' for a post-firmware one. uea_disconnect() instead tells the two apart by the number of interfaces of the active configuration (a pre-firmware device exposes a single interface, ADI930 has 2 and eagle has 3), and casts the interface data accordingly. Because the two handlers use different criteria, a crafted device that advertises a pre-firmware id together with a multi-interface descriptor (or a post-firmware id with a single interface) makes them disagree: the small 'struct completion' stored by uea_probe() is then passed to usbatm_usb_disconnect(), which casts it to 'struct usbatm_data' and takes instance->serialize, reading past the end of the allocation: BUG: KASAN: slab-out-of-bounds in __mutex_lock+0x152a/0x1b80 Read of size 8 at addr ffff8880470e2c60 by task kworker/1:2/982 ... __mutex_lock+0x152a/0x1b80 usbatm_usb_disconnect+0x70/0x820 uea_disconnect+0x133/0x2c0 usb_unbind_interface+0x1dd/0x9e0 ... which belongs to the cache kmalloc-96 of size 96 The buggy address is located 0 bytes to the right of allocated 96-byte region [ffff8880470e2c00, ffff8880470e2c60) Reject such inconsistent descriptors in uea_probe() so that both handlers always make the same pre/post-firmware decision. | ||||
| CVE-2026-68343 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: smb: client: validate DFS referral PathConsumed parse_dfs_referrals() validates that the response contains the fixed referral entry array and, on for-next, the per-referral string offsets. However, the response also contains a PathConsumed value that is later used for DFS path parsing. If a malformed response provides a PathConsumed value larger than the search name, later DFS parsing can advance beyond the end of the path. Validate PathConsumed against the search name length before storing it in the parsed referral. | ||||
| CVE-2026-68342 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ovpn: avoid putting unrelated P2P peer on socket release ovpn_peer_release_p2p() is called when an OVPN UDP socket is being destroyed. It checks the currently published P2P peer and releases it only if that peer still uses the socket being destroyed. A peer replacement can publish a new peer before the old UDP socket is destroyed. When the old socket destruction path runs afterwards, ovpn_peer_release_p2p() observes the new peer through ovpn->peer. Since the new peer uses a different socket, the function takes the socket mismatch branch. That branch still calls ovpn_peer_put(peer). At this point, however, peer is the currently published replacement peer, not the peer associated with the socket being destroyed. Dropping its reference can free it while ovpn->peer still points to it, leading to later use-after-free accesses from the peer and socket cleanup paths. KASAN reports this as a slab-use-after-free on the kmalloc-1k ovpn_peer object. In the reproducer, the object is allocated from ovpn_peer_new() via ovpn_nl_peer_new_doit(), and freed through ovpn_peer_release_rcu() from RCU callback processing. Observed access sites include ovpn_peer_remove(), ovpn_socket_release(), ovpn_nl_peer_del_notify(), and unlock_ovpn(). Fix this by returning from the socket mismatch branch without putting the peer. | ||||
| CVE-2026-68341 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ovpn: fix use after free in unlock_ovpn() unlock_ovpn() iterates over the release_list using llist_for_each_entry() and drops the peer reference inside the loop body via ovpn_peer_put(). If this drops the last reference, the peer is eventually freed. However, llist_for_each_entry() reads peer->release_entry.next in the loop advance expression, which runs after the body. By that time the peer may have already been freed, resulting in a use after free when advancing to the next list entry. Fix this by using llist_for_each_entry_safe(), which caches the next pointer before executing the loop body. | ||||
| CVE-2026-68340 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: hwmon: occ: validate poll response sensor blocks The OCC poll response parser walks a counted list of sensor data blocks. It used the static backing-array capacity as the parse boundary, but a transport response makes only data_length bytes current and valid. A truncated response can therefore make the parser consume a block header or block extent outside the current response. Use data_length as the parent boundary, prove the fixed poll header and each current block header before reading them, and prove the complete block before advancing. Keep parsed sensor metadata local until the complete response has passed validation, then publish it. Propagate malformed-response errors before publishing the OCC as active. | ||||
| CVE-2026-68339 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btusb: validate Realtek vendor event length btusb_recv_event_realtek() reads the event code at data[0] and the Realtek subevent code at data[2] before deciding whether to consume a vendor event as a coredump. For example, the two-byte event ff 00 contains a complete vendor-event header declaring zero parameters. The old classifier still reads a nonexistent third byte and can misclassify the event as a coredump if the adjacent byte is 0x34. Require the HCI event header and first parameter to be present before inspecting the Realtek subevent code. Short events continue through the normal HCI receive path, which owns their protocol validation. | ||||
| CVE-2026-68338 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: net/packet: avoid fanout hook re-registration after unregister packet_set_ring() temporarily detaches a socket from packet delivery while reconfiguring its ring. It records the previous running state, clears po->num, unregisters the protocol hook when needed, drops po->bind_lock, and later restores po->num and re-registers the hook from the saved was_running value. That unlocked window can race with NETDEV_UNREGISTER. The notifier can observe the socket as not running, skip __unregister_prot_hook(), and invalidate the per-socket binding by setting po->ifindex to -1 and clearing po->prot_hook.dev. A one-member fanout group can still retain its shared fanout hook device pointer. When packet_set_ring() resumes, re-registering solely from the stale was_running state can re-add the fanout hook after the device has been unregistered. Treat po->ifindex == -1 as an invalidated binding after reacquiring po->bind_lock. This is distinct from ifindex 0, the normal unbound/wildcard state: ifindex -1 marks an existing device binding that was invalidated when the device was unregistered. Restore po->num as before, but do not re-register the hook if device unregister already detached the socket. | ||||
| CVE-2026-68337 | 1 Linux | 1 Linux Kernel | 2026-08-10 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: bpf: Reject redirect helpers without a bpf_net_context The bpf_redirect*() helpers and skb_do_redirect() obtain the per-task bpf_redirect_info via bpf_net_ctx_get_ri(), which dereferences the current->bpf_net_context unconditionally. That context is established on the paths that run tc BPF such as sch_handle_{ingress,egress}(), *except* for the case where {cls,act}_bpf was attached to a proper qdisc. A program running from there reaches the NULL deref in two ways: * It calls bpf_redirect() directly, which dereferences the context at the top of the helper: tc qdisc add dev eth0 root handle 1: red limit 1MB min 10KB max 20KB \ avpkt 1000 burst 100 qevent early_drop block 10 tc filter add block 10 pref 1 bpf obj redirect.o * It simply returns TC_ACT_REDIRECT without helper call: tcf_qevent_handle() then dispatches to skb_do_redirect(), which dereferences the context Rather than extending bpf_net_context management into the qdisc path, make the redirect helpers refuse to operate when no context exists, and have tcf_qevent_handle() drop a TC_ACT_REDIRECT verdict instead of calling skb_do_redirect(). Previous behaviour was a crash, so nothing regresses by not supporting it. | ||||