| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: serialize udp bearer replicast list updates
tipc_udp_rcast_add() and cleanup_bearer() both update ub->rcast.list with
list_add_rcu() / list_del_rcu(), but nothing serializes them. The add runs
from the encap receive softirq (via tipc_udp_rcast_disc()) without
rtnl_lock(), so it can race the cleanup delete and corrupt the list:
list_del corruption. prev->next should be ffff8880298d7ab8,
but was ffff88802449ad38. (prev=ffff888027e3ec98)
kernel BUG at lib/list_debug.c:62!
RIP: __list_del_entry_valid_or_report+0x17a/0x200
Workqueue: events cleanup_bearer
Call Trace:
cleanup_bearer (net/tipc/udp_media.c:811)
process_one_work (kernel/workqueue.c:3302)
worker_thread (kernel/workqueue.c:3466)
The bearer can be enabled from an unprivileged user namespace, as the
TIPCv2 generic-netlink ops carry no GENL_ADMIN_PERM.
Add a spinlock to struct udp_bearer and take it around the list_add_rcu()
in tipc_udp_rcast_add() and the list_del_rcu() loop in cleanup_bearer() so
the two writers can no longer corrupt the list.
Reject a duplicate peer under the same lock before allocating, and remove
tipc_udp_is_known_peer(). The old lockless pre-check in
tipc_udp_rcast_disc() was racy: two softirqs discovering the same peer
could both find it absent and add it twice.
cleanup_bearer() runs from a workqueue after tipc_udp_disable() clears the
bearer's up bit, so an encap softirq can still reach tipc_udp_rcast_add()
and add a peer after cleanup_bearer() has already emptied the list, leaking
that entry when the bearer is freed. Mark the bearer disabled under
rcast_lock once the list is emptied and refuse further additions. |
| In the Linux kernel, the following vulnerability has been resolved:
rds: Fix inet6_addr_lst NULL dereference when IPv6 is disabled
When booting with the 'ipv6.disable=1' parameter, inet6_addr_lst
is never initialized because inet6_init() exits before addrconf_init()
is called to initialize it. An attempt to bind an RDS socket to
an ipv6 address results in a crash in __ipv6_chk_addr_and_flags()
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
RIP: 0010:__ipv6_chk_addr_and_flags+0x1df/0x7e0
Call Trace:
<TASK>
ipv6_chk_addr+0x3b/0x50
rds_tcp_laddr_check+0x155/0x3b0 [rds_tcp]
rds_trans_get_preferred+0x15d/0x2d0 [rds]
? trace_hardirqs_on+0x2d/0x110
rds_bind+0x1433/0x1d60 [rds]
? rds_remove_bound+0xd50/0xd50 [rds]
? aa_af_perm+0x250/0x250
? __might_fault+0xde/0x190
? __sys_bind+0x1dc/0x210
__sys_bind+0x1dc/0x210
? __ia32_sys_socketpair+0x100/0x100
? restore_fpregs_from_fpstate+0x53/0x100
__x64_sys_bind+0x73/0xb0
? syscall_enter_from_user_mode+0x1c/0x50
do_syscall_64+0x34/0x80
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
RIP: 0033:0x7f47f8269ea9
</TASK>
The following code reproduces the issue:
struct sockaddr_in6 addr;
s = socket(PF_RDS, SOCK_SEQPACKET, 0);
memset(&addr, 0, sizeof(addr));
inet_pton(AF_INET6, ADDRESS, &addr.sin6_addr);
addr.sin6_family = AF_INET6;
addr.sin6_port = htons(PORT);
bind(s, &addr, sizeof(addr));
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
net: txgbe: fix FDIR filter leak on remove
Perfect FDIR filters can be added while the interface is down and are
kept on the software list for later restore. unregister_netdev() only
calls ndo_stop when the device is up, so txgbe_fdir_filter_exit() in
txgbe_close() is skipped in that case and the filters are leaked on
driver remove. Free the filter list from txgbe_remove() as well. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: fix auth_chunk_list capacity check in sctp_auth_ep_add_chunkid
sctp_auth_ep_add_chunkid() uses SCTP_NUM_CHUNK_TYPES (20) as the
capacity limit for ep->auth_chunk_list, allowing it to hold up to
20 chunk entries (param_hdr.length up to 24). However, the copy
destination asoc->c.auth_chunks in struct sctp_cookie is only
SCTP_AUTH_MAX_CHUNKS (16) entries (20 bytes). When more than 16
chunks are added, sctp_association_init() memcpy overflows the
destination by up to 4 bytes.
Fix by using SCTP_AUTH_MAX_CHUNKS as the capacity limit, matching
the destination capacity. |
| In the Linux kernel, the following vulnerability has been resolved:
pds_core: fix deadlock between reset thread and remove
pci_reset_function() acquires device_lock before performing the reset.
pdsc_remove() is called by the PCI core with device_lock already held.
If pdsc_pci_reset_thread() is running when pdsc_remove() is called,
destroy_workqueue() will block waiting for the work to complete, while
the work is blocked waiting for device_lock - deadlock.
Use pci_try_reset_function() which uses pci_dev_trylock() internally.
This acquires both the device lock and the PCI config access lock
without blocking - if either lock is contended, it returns -EAGAIN
immediately. This avoids the deadlock while also ensuring proper
config space access serialization during the reset.
The pci_dev_get/put calls are also removed as they were unnecessary -
the driver-owned workqueue is destroyed in pdsc_remove(), guaranteeing
the work completes before remove returns. The PCI core holds its
reference to pci_dev throughout the entire unbind sequence. |
| In the Linux kernel, the following vulnerability has been resolved:
pds_core: fix use-after-free on workqueue during remove
In pdsc_remove(), the workqueue is destroyed before pdsc_teardown()
is called. This ordering allows two paths to queue work on the
destroyed workqueue:
1. If pdsc_teardown() -> pdsc_devcmd_reset() times out, the error
path in pdsc_devcmd_locked() queues health_work.
2. A NotifyQ event can trigger the ISR and queue work before free_irq()
is called in pdsc_teardown().
Fix by moving destroy_workqueue() after pdsc_teardown() so the
workqueue outlives every queuer; destroy_workqueue() then flushes any
work still pending.
Draining the queued work also requires ordering the teardown so the
resources that work touches are freed last:
- In pdsc_qcq_free(), after freeing the interrupt, cancel_work_sync()
the queue's work and only then clear qcq->intx, so
pdsc_process_adminq()'s read of qcq->intx for interrupt-credit
return cannot race with the clear.
- Free adminqcq before notifyqcq: the shared adminq ISR is released
when adminqcq is freed, and the adminq work accesses notifyqcq, so
both must be stopped before notifyqcq is freed. |
| In the Linux kernel, the following vulnerability has been resolved:
pds_core: fix auxiliary device add/del races
Two paths add or delete the same slot (pf->vfs[vf_id].padev): a VF's
pdsc_reset_done() and the PF's devlink enable_vnet/disable_vnet handler.
They serialize on config_lock, but neither guards the slot under it
correctly.
add() registers and stores a new auxiliary device without first checking
the slot, so a second add of an already-populated slot leaks the first
device. del() makes that check outside config_lock, so two concurrent
dels can both pass it; the first clears the slot, and the second
dereferences a NULL pointer.
Check and update the slot under config_lock in both paths. |
| In the Linux kernel, the following vulnerability has been resolved:
accel: ethosu: Fix element size accounting for cmd stream validation
There are 2 issues with the element size handling in the command stream
validation which result in too small of a size calculated when the
element size is 16/32/64 bits.
For NHWC format, the element size is simply missing from the
calculation.
The bitfield for the element size is different between IFM/IFM2 and
OFM. IFM and IFM2 encode the precision in parameter bits 2:3, while OFM
uses bits 1:2. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: validate stream count in sctp_process_strreset_inreq()
When processing a RESET_IN_REQUEST from a peer,
sctp_process_strreset_inreq() derives the stream count from the
parameter length but does not check whether the resulting
RESET_OUT_REQUEST would exceed SCTP_MAX_CHUNK_LEN.
The OUT request header (sctp_strreset_outreq, 16 bytes) is 8 bytes
larger than the IN request header (sctp_strreset_inreq, 8 bytes).
Generally, the IP payload is bounded to 65535 bytes, so the stream
list cannot be large enough to trigger the overflow. However, on
interfaces with MTU > 65535 (e.g., loopback with IPv6 jumbograms), a
stream list that fits within the incoming IN parameter can cause a
__u16 overflow in sctp_make_strreset_req() when computing the OUT
request size, leading to an undersized skb allocation and a kernel
BUG:
net/core/skbuff.c:207 skb_panic
net/core/skbuff.c:2625 skb_put
net/sctp/sm_make_chunk.c:1535 sctp_addto_chunk
net/sctp/sm_make_chunk.c:3695 sctp_make_strreset_req
net/sctp/stream.c:655 sctp_process_strreset_inreq
The local setsockopt path validates the generated reset request size.
However, for an incoming-only reset, it accounts for the smaller IN
request even though the peer must generate an OUT request with the same
stream list. Such a request cannot be completed successfully by the
peer.
Reject peer IN requests whose corresponding OUT request would exceed
SCTP_MAX_CHUNK_LEN. Also tighten the local check so it does not send an
IN request that would require an oversized OUT request from the peer. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mctp i3c: clean up notifier and buses if driver register fails
mctp_i3c_mod_init() registers the I3C bus notifier and then walks the
existing buses with i3c_for_each_bus_locked(mctp_i3c_bus_add_new, NULL)
before registering the I3C device driver. If i3c_driver_register()
fails, the function returns the error directly, leaving the notifier
registered and every mctp_i3c_bus object created for the existing buses
allocated. The notifier is left pointing into the module that failed to
load and the bus list is leaked.
Mirror the module exit path on this failure: unregister the notifier and
tear down the buses that were added before returning the error.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code. |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: fix infinite loop in __tipc_nl_compat_dumpit
cmd->dumpit callback can return a negative errno, causing an infinite
loop due to the while(len) condition. As the loop never terminates,
genl_mutex is never released, and other tasks waiting on it starve in D
state.
Check dumpit's return value, propagate it and jump to err_out on error. |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: fix cifsFileInfo leak on kmalloc failure in deferred close drain paths
In cifs_close_deferred_file(), cifs_close_all_deferred_files(), and
cifs_close_deferred_file_under_dentry(), when a pending deferred close
is cancelled via cancel_delayed_work(), the subsequent kmalloc_obj() to
add the file to the local processing list may fail under memory pressure.
The loop breaks immediately, but the cancelled work is no longer pending
(it would have called _cifsFileInfo_put()), and the cfile is never added
to file_head for processing. The cifsFileInfo reference and the open
server handle both leak.
Fix by saving the cfile that failed allocation in a local variable,
breaking as before, and calling _cifsFileInfo_put() on it after
releasing the lock. Any files later in the iteration are unaffected
since their deferred work is still pending and will fire normally. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7925: guard link STA in decap offload
mt7925_sta_set_decap_offload() iterates over the vif valid_links mask
when updating decap offload state for an MLO station. The station may not
have a link STA for every valid link of the vif, so mt792x_sta_to_link()
can return NULL for a link that belongs to the vif but not to the station.
The function currently dereferences mlink before checking whether the
link WCID is ready. If mlink is NULL, setting or clearing
MT_WCID_FLAG_HDR_TRANS dereferences a NULL pointer.
Skip links without a station link before touching mlink->wcid. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: guard HE capability lookups
mt7915_mcu_bss_he_tlv() and mt7915_mcu_sta_bfer_tlv() both run after
checking HE support, then dereference the HE PHY capability returned by
mt76_connac_get_he_phy_cap(). That helper can return NULL when no
capability entry matches the vif type.
Fetch the capability before appending the TLV and skip the HE-specific
setup when no matching capability is available. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: connac: fix possible NULL-pointer deref in mt76_connac_mcu_uni_bss_he_tlv()
mt76_connac_get_he_phy_cap routine can theoretically return NULL so
check cap pointer before dereferencing it. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: check pointer returned by mt76_connac_get_he_phy_cap()
mt76_connac_get_he_phy_cap routine can theoretically return NULL so
check cap pointer before dereferencing it. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7925: fix crash in reset link replay
During reset recovery, mt7925_vif_connect_iter() replays firmware state
for links tracked in mvif->valid_links. After MLO link changes or MCU
timeout recovery, the driver bitmap can temporarily contain a link whose
mac80211 bss_conf has already gone away.
This can pass a NULL bss_conf to mt76_connac_mcu_uni_add_dev(), matching
the crash where x1, the second argument, is NULL:
pc : mt76_connac_mcu_uni_add_dev+0x8c/0x1f8 [mt76_connac_lib]
lr : mt7925_vif_connect_iter+0x9c/0x168 [mt7925_common]
x2 : ffffff80a77f6018 x1 : 0000000000000000 x0 : ffffff8099402080
Call trace:
mt76_connac_mcu_uni_add_dev+0x8c/0x1f8 [mt76_connac_lib]
mt7925_vif_connect_iter+0x9c/0x168 [mt7925_common]
mt7925_mac_reset_work+0x264/0x2f8 [mt7925_common]
Skip missing bss_conf entries before replaying the link. Non-MLO AP/STA
reset replay is unchanged because the helper still returns &vif->bss_conf
for the legacy link. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: fix possible NULL-pointer deref in mt7996_mcu_sta_bfer_eht()
mt76_connac_get_eht_phy_cap routine can theoretically return NULL so
check cap pointer before dereferencing it. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/vf: Add drm_dev guards when detaching CCS read/write buffers
CCS read/write buffers are freed during BO destruction. In some cases,
BOs may be destroyed after the device is unbound but while the DRM
structure remains valid, leading to NULL pointer dereferences when
accessing device resources.
BUG: kernel NULL pointer dereference, address: 0000000000000000
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP NOPTI
CPU: 0 UID: 0 PID: 9376 Comm: xe_pat Not tainted 7.2.0-rc2+ #1 PREEMPT(lazy)
RIP: 0010:xe_sriov_vf_ccs_rw_update_bb_addr+0x4d/0xa0 [xe]
RSP: 0018:ffffcf304110b9c8 EFLAGS: 00010246
RAX: ffff8a85c38a0a00 RBX: 00000000810ef000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8a85c39c1888
RBP: ffffcf304110b9e8 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8a85c39c1888
R13: 0000000000000000 R14: ffff8a85c39b4f28 R15: ffff8a85c3885000
FS: 0000000000000000(0000) GS:ffff8a878b809000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000010314a002 CR4: 0000000000772ef0
PKRU: 55555554
Call Trace:
<TASK>
xe_migrate_ccs_rw_copy_clear+0x98/0x120 [xe]
xe_sriov_vf_ccs_detach_bo+0x2c/0x60 [xe]
xe_ttm_bo_delete_mem_notify+0xc8/0xe0 [xe]
ttm_bo_cleanup_memtype_use+0x26/0x80 [ttm]
ttm_bo_release+0x29e/0x2d0 [ttm]
ttm_bo_fini+0x39/0x70 [ttm]
xe_gem_object_free+0x1f/0x30 [xe]
drm_gem_object_free+0x1d/0x40
ttm_bo_vm_close+0x5f/0x90 [ttm]
remove_vma+0x2c/0x70
tear_down_vmas+0x63/0xf0
exit_mmap+0x20d/0x3f0
__mmput+0x45/0x170
mmput+0x31/0x40
do_exit+0x2ba/0xac0
do_group_exit+0x2d/0xb0
__x64_sys_exit_group+0x18/0x20
x64_sys_call+0x14a0/0x2390
do_syscall_64+0xdd/0x640
? count_memcg_events+0xea/0x240
? handle_mm_fault+0x1ec/0x2f0
(cherry picked from commit 1ae415a6eefe5004954a1d352b1718faca8844ef) |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: fix 802.1X-SHA256 call trace warning
Based on wpa_auth as 1x_256 mode, need to set up
"use_fwsup" with BRCMF_PROFILE_FWSUP_1X.
Or it will happen trace warning when call brcmf_cfg80211_set_pmk().
[ 4481.831101] ------------[ cut here ]------------
[ 4481.831102] WARNING: CPU: 1 PID: 2997 at
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:7242 brcmf_cfg80211_set_pmk+0x77/0xd0 [brcmfmac]
[...]
[ 4481.831202] Call Trace:
[ 4481.831204] <TASK>
[ 4481.831205] nl80211_set_pmk+0x183/0x250 [cfg80211]
[ 4481.831233] genl_family_rcv_msg_doit+0xea/0x150
[ 4481.831237] genl_rcv_msg+0x104/0x240
[ 4481.831239] ? cfg80211_probe_status+0x2c0/0x2c0 [cfg80211]
[ 4481.831257] ? genl_family_rcv_msg_doit+0x150/0x150
[ 4481.831259] netlink_rcv_skb+0x4e/0x100
[ 4481.831261] genl_rcv+0x24/0x40
[ 4481.831262] netlink_unicast+0x236/0x380
[ 4481.831264] netlink_sendmsg+0x250/0x4b0
[ 4481.831266] sock_sendmsg+0x5c/0x70
[ 4481.831269] ____sys_sendmsg+0x236/0x2b0
[ 4481.831271] ? copy_msghdr_from_user+0x6d/0xa0
[ 4481.831272] ___sys_sendmsg+0x86/0xd0
[ 4481.831274] ? avc_has_perm+0x8c/0x1a0
[ 4481.831276] ? preempt_count_add+0x6a/0xa0
[ 4481.831279] ? sock_has_perm+0x82/0xa0
[ 4481.831280] __sys_sendmsg+0x57/0xa0
[ 4481.831282] do_syscall_64+0x38/0x90
[ 4481.831284] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 4481.831286] RIP: 0033:0x7fd270d369b4 |
