| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/virtio: use uninterruptible resv lock for plane updates
virtio_gpu_cursor_plane_update() and virtio_gpu_resource_flush() lock
the framebuffer BO's dma_resv via virtio_gpu_array_lock_resv() and
ignore its return value. The function can fail with -EINTR from
dma_resv_lock_interruptible() (signal during lock wait) or with
-ENOMEM from dma_resv_reserve_fences() (fence slot allocation),
leaving the resv lock not held. The queue path then walks the object
array and calls dma_resv_add_fence(), which requires the lock held;
with lockdep enabled this trips dma_resv_assert_held():
WARNING: drivers/dma-buf/dma-resv.c:296 at dma_resv_add_fence+0x71e/0x840
Call Trace:
virtio_gpu_array_add_fence
virtio_gpu_queue_ctrl_sgs
virtio_gpu_queue_fenced_ctrl_buffer
virtio_gpu_cursor_plane_update
drm_atomic_helper_commit_planes
drm_atomic_helper_commit_tail
commit_tail
drm_atomic_helper_commit
drm_atomic_commit
drm_atomic_helper_update_plane
__setplane_atomic
drm_mode_cursor_universal
drm_mode_cursor_common
drm_mode_cursor_ioctl
drm_ioctl
__x64_sys_ioctl
Beyond the WARN, mutating the dma_resv fence list without the lock
races with concurrent readers/writers and can corrupt the list.
Both call sites run inside the .atomic_update plane callback, which
DRM atomic helpers do not allow to fail (by the time it runs, the
commit has been signed off to userspace and there is no clean
rollback path). Moving the lock acquisition to .prepare_fb was
rejected because the broader lock scope deadlocks against other BO
locking paths in the same atomic commit.
Introduce virtio_gpu_lock_one_resv_uninterruptible() that uses
dma_resv_lock() instead of dma_resv_lock_interruptible(). This
eliminates the -EINTR failure mode -- the realistic syzbot trigger
-- without extending the lock hold across the commit. The helper
locks a single BO and rejects nents > 1 with -EINVAL; both fix
sites lock exactly one BO.
Use it from virtio_gpu_cursor_plane_update() and
virtio_gpu_resource_flush(); check the return value to handle the
remaining -ENOMEM case from dma_resv_reserve_fences() by freeing
the objs and skipping the plane update for that frame. The
framebuffer BOs touched here are not shared with other contexts
and lock contention is expected to be brief, so the loss of
signal-interruptibility is acceptable.
Other callers of virtio_gpu_array_lock_resv() (the ioctl paths)
continue to use the interruptible variant.
The bug was reported by syzbot, triggered via fault injection
(fail_nth) on the DRM_IOCTL_MODE_CURSOR path, which forces the
-ENOMEM branch in dma_resv_reserve_fences(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/v3d: Fix use-after-free of CPU job query arrays on error path
The CPU job ioctl's fail label calls kvfree() on cpu_job's timestamp and
performance query arrays after v3d_job_cleanup(), which drops the job's
last reference and frees cpu_job. Reading cpu_job at that point is a
use-after-free. Also, on the early v3d_job_init() failure path, it is a
NULL dereference, since v3d_job_deallocate() zeroes the local pointer.
In the success path, the arrays are released from the scheduler's
.free_job callback, but on the error path, they are freed manually, as
the job was never pushed to the scheduler. While the success path deals
with this correctly, the fail path doesn't.
On top of that, the manual kvfree() calls only free the array storage;
they don't drm_syncobj_put() the per-query syncobjs that
v3d_timestamp_query_info_free() and v3d_performance_query_info_free()
release on the success path. So the same fail path that triggers the
use-after-free also leaks one syncobj reference per query.
Unify the CPU job teardown into the CPU job's kref destructor, mirroring
v3d_render_job_free(). The scheduler's .free_job slot reverts to the
generic v3d_sched_job_free() and the fail label drops the manual
kvfree() calls, leaving a single teardown path that is reached from both
the scheduler and the ioctl error path. That removes the use-after-free,
the NULL dereference, and the syncobj leak by construction. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: Fix shrinker deadlock
With PROVE_LOCKING on an Snapdragon X1 and VM reclaim pressure, we see:
======================================================
WARNING: possible circular locking dependency detected
7.0.0-debug+ #43 Tainted: G W
------------------------------------------------------
kswapd0/82 is trying to acquire lock:
ffff800080ec3870 (reservation_ww_class_acquire){+.+.}-{0:0}, at: msm_gem_shrinker_scan+0x17c/0x400 [msm]
but task is already holding lock:
ffffc31709b263b8 (fs_reclaim){+.+.}-{0:0}, at: balance_pgdat+0x88/0x988
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (fs_reclaim){+.+.}-{0:0}:
__lock_acquire+0x4d0/0xad0
lock_acquire.part.0+0xc4/0x248
lock_acquire+0x8c/0x248
fs_reclaim_acquire+0xd0/0xf0
dma_resv_lockdep+0x224/0x348
do_one_initcall+0x84/0x5d0
do_initcalls+0x194/0x1d8
kernel_init_freeable+0x128/0x180
kernel_init+0x2c/0x160
ret_from_fork+0x10/0x20
-> #1 (reservation_ww_class_mutex){+.+.}-{4:4}:
__lock_acquire+0x4d0/0xad0
lock_acquire.part.0+0xc4/0x248
lock_acquire+0x8c/0x248
dma_resv_lockdep+0x1a8/0x348
do_one_initcall+0x84/0x5d0
do_initcalls+0x194/0x1d8
kernel_init_freeable+0x128/0x180
kernel_init+0x2c/0x160
ret_from_fork+0x10/0x20
-> #0 (reservation_ww_class_acquire){+.+.}-{0:0}:
check_prev_add+0x114/0x790
validate_chain+0x594/0x6f0
__lock_acquire+0x4d0/0xad0
lock_acquire.part.0+0xc4/0x248
lock_acquire+0x8c/0x248
drm_gem_lru_scan+0x1ac/0x440
msm_gem_shrinker_scan+0x17c/0x400 [msm]
do_shrink_slab+0x150/0x4a0
shrink_slab+0x144/0x460
shrink_one+0x9c/0x1b0
shrink_many+0x27c/0x5c0
shrink_node+0x344/0x550
balance_pgdat+0x2c0/0x988
kswapd+0x11c/0x318
kthread+0x10c/0x128
ret_from_fork+0x10/0x20
other info that might help us debug this:
Chain exists of:
reservation_ww_class_acquire --> reservation_ww_class_mutex --> fs_reclaim
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(fs_reclaim);
lock(reservation_ww_class_mutex);
lock(fs_reclaim);
lock(reservation_ww_class_acquire);
*** DEADLOCK ***
1 lock held by kswapd0/82:
#0: ffffc31709b263b8 (fs_reclaim){+.+.}-{0:0}, at: balance_pgdat+0x88/0x988
stack backtrace:
CPU: 4 UID: 0 PID: 82 Comm: kswapd0 Tainted: G W 7.0.0-debug+ #43 PREEMPT(full)
Tainted: [W]=WARN
Hardware name: LENOVO 21BX0016US/21BX0016US, BIOS N3HET94W (1.66 ) 09/15/2025
Call trace:
show_stack+0x20/0x40 (C)
dump_stack_lvl+0x9c/0xd0
dump_stack+0x18/0x30
print_circular_bug+0x114/0x120
check_noncircular+0x178/0x198
check_prev_add+0x114/0x790
validate_chain+0x594/0x6f0
__lock_acquire+0x4d0/0xad0
lock_acquire.part.0+0xc4/0x248
lock_acquire+0x8c/0x248
drm_gem_lru_scan+0x1ac/0x440
msm_gem_shrinker_scan+0x17c/0x400 [msm]
do_shrink_slab+0x150/0x4a0
shrink_slab+0x144/0x460
shrink_one+0x9c/0x1b0
shrink_many+0x27c/0x5c0
shrink_node+0x344/0x550
balance_pgdat+0x2c0/0x988
kswapd+0x11c/0x318
kthread+0x10c/0x128
ret_from_fork+0x10/0x20
kswapd0 holding fs_reclaim calls the MSM shrinker, which calls
dma_resv_lock. This in turn acquires fs_reclaim.
Fix this deadlock by using dma_resv_trylock() instead, dropping the
subsequently unused passed wait-wound lock 'ticket'.
Patchwork: https://patchwork.freedesktop.org/patch/723564/
[rob: fixup compile errors, replace lockdep splat with somethin
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
fwctl: pds: Validate RPC input size before parsing
The fwctl core allocates the device-specific RPC input buffer with
fwctl_rpc.in_len and passes that buffer to the driver callback.
pdsfc_fw_rpc() casts the buffer to struct fwctl_rpc_pds and then calls
pdsfc_validate_rpc(), which reads fields from that structure before
checking that the input buffer is large enough to contain it. A short
in_len can make pds_fwctl read beyond the allocation.
Reject pds RPC buffers that are smaller than struct fwctl_rpc_pds before
parsing any pds-specific fields. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tp_meter: fix tp_vars reference leak in receiver shutdown
The receiver shutdown timer handler, batadv_tp_receiver_shutdown(), is
responsible for releasing the tp_vars reference it holds. However, the
existing logic for coordinating this release with batadv_tp_stop_all() was
flawed.
timer_shutdown_sync() guarantees the timer will not fire again after it
returns, but it returns non-zero only when the timer was pending at the
time of the call. If the timer had already expired (and
batadv_tp_stop_all() would unsucessfully try to rearm itself),
batadv_tp_stop_all() skips its batadv_tp_vars_put(), and
batadv_tp_receiver_shutdown() fails to put its own reference as well.
Fix this by introducing a new atomic variable receiving that is set to 1
when the receiver is initialized and cleared atomically with atomic_xchg()
by whichever side claims it first. Only the side that observes the
transition from 1 to 0 is responsible for releasing the tp_vars timer
reference, eliminating the uncertainty. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tp_meter: directly shut down timer on cleanup
batadv_tp_sender_cleanup() was calling timer_delete_sync() followed by
timer_delete() to guard against the timer handler re-arming itself between
the two calls. This double-deletion hack relied on the sending status being
set to 0 to suppress re-arming.
Replace both calls with a single timer_shutdown_sync(). This function both
waits for any running timer callback to complete (like timer_delete_sync())
and permanently disarms the timer so it cannot be re-armed afterwards,
making re-arming prevention unconditional and self-documenting.
The re-arming property is also required because otherwise:
1. context 0 (batadv_tp_recv_ack()) checks in
batadv_tp_reset_sender_timer() if sending is still 1 -> it is
2. context 1 changes in batadv_tp_sender_shutdown() sending to 0 and in
this process forces the kthread to stop timer in
batadv_tp_sender_cleanup()
3. context 0 continues in batadv_tp_reset_sender_timer() and rearms the
timer -> but the reference for it is already gone |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: fix TOCTOU race for reported vlans
The local TT based TVLV is generated by first checking the number of VLANs
which have at least one TT entry. A new buffer with the correct size for
the VLANs is then allocated. Only then, the list of VLANs s used to fill
the VLAN entries in the buffer. During this time, the meshif_vlan_list_lock
is held. But the actual number of TT entries of each VLAN can still
increase during this time - just not the number of VLANs in the list.
But the prefilter used in the buffer size calculation might still cause an
increase of the number of VLANs which need to be stored. Simply because a
VLAN might now suddenly have at least one entry when it had none in the
pre-alloc check - and then needs to occupy space which was not allocated.
It is better to overestimate the buffer size at the beginning and then fill
the buffer only with the VLANs which are not empty. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: avoid empty VLAN responses
The commit 16116dac2339 ("batman-adv: prevent TT request storms by not
sending inconsistent TT TLVLs") added checks to the local (direct) TT
response code. But the response can also be done indirectly by another node
using the global TT state. To avoid such inconsistency states reported in
the original fix, also avoid sending empty VLANs for replies from the
global TT state. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: fix negative last_changeset_len
batadv_piv_tt::last_changeset_len len was declared as s16, but the field is
never intended to hold a negative value. When a value greater than 32767 is
assigned, it wraps to a negative signed integer.
In batadv_send_my_tt_response(), last_changeset_len is temporarily widened
to s32. The incorrectly negative s16 value propagates into the s32, causing
batadv_tt_prepare_tvlv_local_data() to allocate a full sized buffer but
populates only a small portion of it with the collected changeset. All
remaining bits are kept uninitialized.
Using an u16 avoids this type confusion and ensures that no (negative) sign
extension is performed in batadv_send_my_tt_response(). |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: fix negative tt_buff_len
batadv_orig_node::tt_buff_len was declared as s16, but the field is never
intended to hold a negative value. When a value greater than 32767 is
assigned, it wraps to a negative signed integer.
In batadv_send_other_tt_response(), tt_buff_len is temporarily widened to
s32. The incorrectly negative s16 value propagates into the s32, causing
batadv_tt_prepare_tvlv_global_data() to allocate a full sized buffer but
populates only a small portion of it with the collected changeset. All
remaining bits are kept uninitialized.
Using an u16 avoids this type confusion and ensures that no (negative) sign
extension is performed in batadv_send_other_tt_response(). |
| In the Linux kernel, the following vulnerability has been resolved:
x86/bugs: Make Safe-RET robust against interrupt injection
An attacker injecting interrupts while the Safe-RET mitigation executes
on machines affected by SRSO can neutralize the safe return sequence,
potentially leading to data leakage through speculative execution.
Fixup register state as if the Safe-RET sequence executed successfully
by "emulating" it, in a manner of speaking, and avoid executing a RET
instruction after returning from the interrupt. |
| In the Linux kernel, the following vulnerability has been resolved:
watchdog: airoha: Prevent division by zero when clock frequency is zero
clk_get_rate() can return 0 when the clock provider is not properly
configured or the clock is unmanaged. The driver uses wdt_freq as a
divisor directly in airoha_wdt_probe() to compute max_timeout and in
airoha_wdt_get_timeleft() to compute the remaining time, which results
in a division by zero.
Add a check for wdt_freq == 0 in probe and return -EINVAL with
dev_err_probe() to prevent the division by zero and provide a
diagnostic message. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix root leak if its reloc root is unexpected in merge_reloc_roots()
If we have an unexpected reloc_root for our root, we jump to the out label
but never drop the reference we obtained for root, resulting in a leak.
Add a missing btrfs_put_root() call. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: don't free the ASCONF's own transport in DEL-IP processing
sctp_process_asconf() caches the transport the ASCONF chunk is processed
against in asconf->transport (== chunk->transport, set once in sctp_rcv()).
For an ASCONF located through its Address Parameter by
__sctp_rcv_asconf_lookup(), that cached transport corresponds to the
Address Parameter, which need not be the packet's source address.
sctp_process_asconf_param() rejects a DEL-IP for the packet source address
(ADDIP D8, SCTP_ERROR_DEL_SRC_IP), but nothing protects asconf->transport.
A single ASCONF can therefore carry, in order:
[Address Parameter L] [DEL-IP L] [DEL-IP 0.0.0.0]
where L differs from the source. The DEL-IP for L passes the D8 check and
calls sctp_assoc_rm_peer() on the transport that asconf->transport still
points at, freeing it (RCU-deferred). The following wildcard DEL-IP then
reuses the now-dangling asconf->transport in sctp_assoc_set_primary() and
sctp_assoc_del_nonprimary_peers(): set_primary() dereferences the freed
transport (->ipaddr, ->state) and plants the dangling pointer into
asoc->peer.primary_path / active_path, and del_nonprimary_peers(), keeping
only the pointer that is no longer on the list, removes every real
transport, leaving the association with a transport_count of 0 and
primary_path/active_path pointing at freed memory.
Reject a DEL-IP that targets the transport the ASCONF is being processed
against, mirroring the existing source-address guard, so the wildcard
branch can never reuse a freed transport. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: hif_usb: don't dereference hif_dev after re-arming firmware request
ath9k_hif_request_firmware() re-arms an asynchronous firmware load via
request_firmware_nowait(), passing hif_dev as the completion context, and
then still dereferences hif_dev:
dev_info(&hif_dev->udev->dev, "ath9k_htc: Firmware %s requested\n",
hif_dev->fw_name);
The re-armed callback ath9k_hif_usb_firmware_cb() runs on the "events"
workqueue and, when the firmware is missing, walks the retry chain into
ath9k_hif_usb_firmware_fail() -> complete_all(&hif_dev->fw_done). That
releases the wait_for_completion(&hif_dev->fw_done) in a concurrent
ath9k_hif_usb_disconnect(), which then kfree()s hif_dev. The trailing
dev_info() in the frame that re-armed the request can therefore read freed
memory (hif_dev->udev, the first field of struct hif_device_usb):
BUG: KASAN: slab-use-after-free in ath9k_hif_request_firmware
Read of size 8 ... by task kworker/...
ath9k_hif_request_firmware
ath9k_hif_usb_firmware_cb drivers/net/wireless/ath/ath9k/hif_usb.c:1247
request_firmware_work_func
Allocated by ...:
ath9k_hif_usb_probe drivers/net/wireless/ath/ath9k/hif_usb.c
Freed by ...:
ath9k_hif_usb_disconnect -> kfree drivers/net/wireless/ath/ath9k/hif_usb.c
The fw_done barrier only makes disconnect wait for the firmware chain to
*terminate*; it does not protect the outer ath9k_hif_request_firmware()
frame that re-armed the request and keeps touching hif_dev afterwards.
Drop the post-request dev_info(): it is the only use of hif_dev after the
async request is armed, and it is purely informational (the dev_err() on the
failure path runs only when request_firmware_nowait() did not arm a callback,
so hif_dev is still alive there).
This was first reported by syzbot as a single, non-reproduced crash that was
later auto-obsoleted, and was independently rediscovered by the reFuzz fuzzer,
which produced a C reproducer (USB-gadget connect/disconnect of an ath9k_htc
device whose firmware download fails). The vulnerable code is unchanged and
still present in v7.1-rc6, where the slab-use-after-free reproduces under KASAN
once the (sub-microsecond) race window is widened. |
