| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: mtk_eth_soc: fix memory corruption during fq dma init
The loop responsible for allocating up to MTK_FQ_DMA_LENGTH buffers must
only touch as many descriptors, otherwise it ends up corrupting unrelated
memory. Fix the loop iteration count accordingly. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: Call iso_exit() on module unload
If iso_init() has been called, iso_exit() must be called on module
unload. Without that, the struct proto that iso_init() registered with
proto_register() becomes invalid, which could cause unpredictable
problems later. In my case, with CONFIG_LIST_HARDENED and
CONFIG_BUG_ON_DATA_CORRUPTION enabled, loading the module again usually
triggers this BUG():
list_add corruption. next->prev should be prev (ffffffffb5355fd0),
but was 0000000000000068. (next=ffffffffc0a010d0).
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:29!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP PTI
CPU: 1 PID: 4159 Comm: modprobe Not tainted 6.10.11-4+bt2-ao-desktop #1
RIP: 0010:__list_add_valid_or_report+0x61/0xa0
...
__list_add_valid_or_report+0x61/0xa0
proto_register+0x299/0x320
hci_sock_init+0x16/0xc0 [bluetooth]
bt_init+0x68/0xd0 [bluetooth]
__pfx_bt_init+0x10/0x10 [bluetooth]
do_one_initcall+0x80/0x2f0
do_init_module+0x8b/0x230
__do_sys_init_module+0x15f/0x190
do_syscall_64+0x68/0x110
... |
| In the Linux kernel, the following vulnerability has been resolved:
r8169: add tally counter fields added with RTL8125
RTL8125 added fields to the tally counter, what may result in the chip
dma'ing these new fields to unallocated memory. Therefore make sure
that the allocated memory area is big enough to hold all of the
tally counter values, even if we use only parts of it. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: use hweight16 to get correct tx antenna
The chainmask is u16 so using hweight8 cannot get correct tx_ant.
Without this patch, the tx_ant of band 2 would be -1 and lead to the
following issue:
BUG: KASAN: stack-out-of-bounds in mt7996_mcu_add_sta+0x12e0/0x16e0 [mt7996e] |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rtrs-clt: Reset cid to con_num - 1 to stay in bounds
In the function init_conns(), after the create_con() and create_cm() for
loop if something fails. In the cleanup for loop after the destroy tag, we
access out of bound memory because cid is set to clt_path->s.con_num.
This commits resets the cid to clt_path->s.con_num - 1, to stay in bounds
in the cleanup loop later. |
| In the Linux kernel, the following vulnerability has been resolved:
igb: cope with large MAX_SKB_FRAGS
Sabrina reports that the igb driver does not cope well with large
MAX_SKB_FRAG values: setting MAX_SKB_FRAG to 45 causes payload
corruption on TX.
An easy reproducer is to run ssh to connect to the machine. With
MAX_SKB_FRAGS=17 it works, with MAX_SKB_FRAGS=45 it fails. This has
been reported originally in
https://bugzilla.redhat.com/show_bug.cgi?id=2265320
The root cause of the issue is that the driver does not take into
account properly the (possibly large) shared info size when selecting
the ring layout, and will try to fit two packets inside the same 4K
page even when the 1st fraglist will trump over the 2nd head.
Address the issue by checking if 2K buffers are insufficient. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/dasd: fix error recovery leading to data corruption on ESE devices
Extent Space Efficient (ESE) or thin provisioned volumes need to be
formatted on demand during usual IO processing.
The dasd_ese_needs_format function checks for error codes that signal
the non existence of a proper track format.
The check for incorrect length is to imprecise since other error cases
leading to transport of insufficient data also have this flag set.
This might lead to data corruption in certain error cases for example
during a storage server warmstart.
Fix by removing the check for incorrect length and replacing by
explicitly checking for invalid track format in transport mode.
Also remove the check for file protected since this is not a valid
ESE handling case. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid1: Fix data corruption for degraded array with slow disk
read_balance() will avoid reading from slow disks as much as possible,
however, if valid data only lands in slow disks, and a new normal disk
is still in recovery, unrecovered data can be read:
raid1_read_request
read_balance
raid1_should_read_first
-> return false
choose_best_rdev
-> normal disk is not recovered, return -1
choose_bb_rdev
-> missing the checking of recovery, return the normal disk
-> read unrecovered data
Root cause is that the checking of recovery is missing in
choose_bb_rdev(). Hence add such checking to fix the problem.
Also fix similar problem in choose_slow_rdev(). |
| In the Linux kernel, the following vulnerability has been resolved:
mm/vmalloc: fix page mapping if vm_area_alloc_pages() with high order fallback to order 0
The __vmap_pages_range_noflush() assumes its argument pages** contains
pages with the same page shift. However, since commit e9c3cda4d86e ("mm,
vmalloc: fix high order __GFP_NOFAIL allocations"), if gfp_flags includes
__GFP_NOFAIL with high order in vm_area_alloc_pages() and page allocation
failed for high order, the pages** may contain two different page shifts
(high order and order-0). This could lead __vmap_pages_range_noflush() to
perform incorrect mappings, potentially resulting in memory corruption.
Users might encounter this as follows (vmap_allow_huge = true, 2M is for
PMD_SIZE):
kvmalloc(2M, __GFP_NOFAIL|GFP_X)
__vmalloc_node_range_noprof(vm_flags=VM_ALLOW_HUGE_VMAP)
vm_area_alloc_pages(order=9) ---> order-9 allocation failed and fallback to order-0
vmap_pages_range()
vmap_pages_range_noflush()
__vmap_pages_range_noflush(page_shift = 21) ----> wrong mapping happens
We can remove the fallback code because if a high-order allocation fails,
__vmalloc_node_range_noprof() will retry with order-0. Therefore, it is
unnecessary to fallback to order-0 here. Therefore, fix this by removing
the fallback code. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix a kernel verifier crash in stacksafe()
Daniel Hodges reported a kernel verifier crash when playing with sched-ext.
Further investigation shows that the crash is due to invalid memory access
in stacksafe(). More specifically, it is the following code:
if (exact != NOT_EXACT &&
old->stack[spi].slot_type[i % BPF_REG_SIZE] !=
cur->stack[spi].slot_type[i % BPF_REG_SIZE])
return false;
The 'i' iterates old->allocated_stack.
If cur->allocated_stack < old->allocated_stack the out-of-bound
access will happen.
To fix the issue add 'i >= cur->allocated_stack' check such that if
the condition is true, stacksafe() should fail. Otherwise,
cur->stack[spi].slot_type[i % BPF_REG_SIZE] memory access is legal. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en : Fix memory out-of-bounds in bnxt_fill_hw_rss_tbl()
A recent commit has modified the code in __bnxt_reserve_rings() to
set the default RSS indirection table to default only when the number
of RX rings is changing. While this works for newer firmware that
requires RX ring reservations, it causes the regression on older
firmware not requiring RX ring resrvations (BNXT_NEW_RM() returns
false).
With older firmware, RX ring reservations are not required and so
hw_resc->resv_rx_rings is not always set to the proper value. The
comparison:
if (old_rx_rings != bp->hw_resc.resv_rx_rings)
in __bnxt_reserve_rings() may be false even when the RX rings are
changing. This will cause __bnxt_reserve_rings() to skip setting
the default RSS indirection table to default to match the current
number of RX rings. This may later cause bnxt_fill_hw_rss_tbl() to
use an out-of-range index.
We already have bnxt_check_rss_tbl_no_rmgr() to handle exactly this
scenario. We just need to move it up in bnxt_need_reserve_rings()
to be called unconditionally when using older firmware. Without the
fix, if the TX rings are changing, we'll skip the
bnxt_check_rss_tbl_no_rmgr() call and __bnxt_reserve_rings() may also
skip the bnxt_set_dflt_rss_indir_tbl() call for the reason explained
in the last paragraph. Without setting the default RSS indirection
table to default, it causes the regression:
BUG: KASAN: slab-out-of-bounds in __bnxt_hwrm_vnic_set_rss+0xb79/0xe40
Read of size 2 at addr ffff8881c5809618 by task ethtool/31525
Call Trace:
__bnxt_hwrm_vnic_set_rss+0xb79/0xe40
bnxt_hwrm_vnic_rss_cfg_p5+0xf7/0x460
__bnxt_setup_vnic_p5+0x12e/0x270
__bnxt_open_nic+0x2262/0x2f30
bnxt_open_nic+0x5d/0xf0
ethnl_set_channels+0x5d4/0xb30
ethnl_default_set_doit+0x2f1/0x620 |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: add missing check_func_arg_reg_off() to prevent out-of-bounds memory accesses
Currently, it's possible to pass in a modified CONST_PTR_TO_DYNPTR to
a global function as an argument. The adverse effects of this is that
BPF helpers can continue to make use of this modified
CONST_PTR_TO_DYNPTR from within the context of the global function,
which can unintentionally result in out-of-bounds memory accesses and
therefore compromise overall system stability i.e.
[ 244.157771] BUG: KASAN: slab-out-of-bounds in bpf_dynptr_data+0x137/0x140
[ 244.161345] Read of size 8 at addr ffff88810914be68 by task test_progs/302
[ 244.167151] CPU: 0 PID: 302 Comm: test_progs Tainted: G O E 6.10.0-rc3-00131-g66b586715063 #533
[ 244.174318] Call Trace:
[ 244.175787] <TASK>
[ 244.177356] dump_stack_lvl+0x66/0xa0
[ 244.179531] print_report+0xce/0x670
[ 244.182314] ? __virt_addr_valid+0x200/0x3e0
[ 244.184908] kasan_report+0xd7/0x110
[ 244.187408] ? bpf_dynptr_data+0x137/0x140
[ 244.189714] ? bpf_dynptr_data+0x137/0x140
[ 244.192020] bpf_dynptr_data+0x137/0x140
[ 244.194264] bpf_prog_b02a02fdd2bdc5fa_global_call_bpf_dynptr_data+0x22/0x26
[ 244.198044] bpf_prog_b0fe7b9d7dc3abde_callback_adjust_bpf_dynptr_reg_off+0x1f/0x23
[ 244.202136] bpf_user_ringbuf_drain+0x2c7/0x570
[ 244.204744] ? 0xffffffffc0009e58
[ 244.206593] ? __pfx_bpf_user_ringbuf_drain+0x10/0x10
[ 244.209795] bpf_prog_33ab33f6a804ba2d_user_ringbuf_callback_const_ptr_to_dynptr_reg_off+0x47/0x4b
[ 244.215922] bpf_trampoline_6442502480+0x43/0xe3
[ 244.218691] __x64_sys_prlimit64+0x9/0xf0
[ 244.220912] do_syscall_64+0xc1/0x1d0
[ 244.223043] entry_SYSCALL_64_after_hwframe+0x77/0x7f
[ 244.226458] RIP: 0033:0x7ffa3eb8f059
[ 244.228582] Code: 08 89 e8 5b 5d c3 66 2e 0f 1f 84 00 00 00 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 8f 1d 0d 00 f7 d8 64 89 01 48
[ 244.241307] RSP: 002b:00007ffa3e9c6eb8 EFLAGS: 00000206 ORIG_RAX: 000000000000012e
[ 244.246474] RAX: ffffffffffffffda RBX: 00007ffa3e9c7cdc RCX: 00007ffa3eb8f059
[ 244.250478] RDX: 00007ffa3eb162b4 RSI: 0000000000000000 RDI: 00007ffa3e9c7fb0
[ 244.255396] RBP: 00007ffa3e9c6ed0 R08: 00007ffa3e9c76c0 R09: 0000000000000000
[ 244.260195] R10: 0000000000000000 R11: 0000000000000206 R12: ffffffffffffff80
[ 244.264201] R13: 000000000000001c R14: 00007ffc5d6b4260 R15: 00007ffa3e1c7000
[ 244.268303] </TASK>
Add a check_func_arg_reg_off() to the path in which the BPF verifier
verifies the arguments of global function arguments, specifically
those which take an argument of type ARG_PTR_TO_DYNPTR |
MEM_RDONLY. Also, process_dynptr_func() doesn't appear to perform any
explicit and strict type matching on the supplied register type, so
let's also enforce that a register either type PTR_TO_STACK or
CONST_PTR_TO_DYNPTR is by the caller. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Fix for possible memory corruption
Init Control Block is dereferenced incorrectly. Correctly dereference ICB |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: configfs: Prevent OOB read/write in usb_string_copy()
Userspace provided string 's' could trivially have the length zero. Left
unchecked this will firstly result in an OOB read in the form
`if (str[0 - 1] == '\n') followed closely by an OOB write in the form
`str[0 - 1] = '\0'`.
There is already a validating check to catch strings that are too long.
Let's supply an additional check for invalid strings that are too short. |
| In the Linux kernel, the following vulnerability has been resolved:
Avoid hw_desc array overrun in dw-axi-dmac
I have a use case where nr_buffers = 3 and in which each descriptor is composed by 3
segments, resulting in the DMA channel descs_allocated to be 9. Since axi_desc_put()
handles the hw_desc considering the descs_allocated, this scenario would result in a
kernel panic (hw_desc array will be overrun).
To fix this, the proposal is to add a new member to the axi_dma_desc structure,
where we keep the number of allocated hw_descs (axi_desc_alloc()) and use it in
axi_desc_put() to handle the hw_desc array correctly.
Additionally I propose to remove the axi_chan_start_first_queued() call after completing
the transfer, since it was identified that unbalance can occur (started descriptors can
be interrupted and transfer ignored due to DMA channel not being enabled). |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: mpt3sas: Avoid test/set_bit() operating in non-allocated memory
There is a potential out-of-bounds access when using test_bit() on a single
word. The test_bit() and set_bit() functions operate on long values, and
when testing or setting a single word, they can exceed the word
boundary. KASAN detects this issue and produces a dump:
BUG: KASAN: slab-out-of-bounds in _scsih_add_device.constprop.0 (./arch/x86/include/asm/bitops.h:60 ./include/asm-generic/bitops/instrumented-atomic.h:29 drivers/scsi/mpt3sas/mpt3sas_scsih.c:7331) mpt3sas
Write of size 8 at addr ffff8881d26e3c60 by task kworker/u1536:2/2965
For full log, please look at [1].
Make the allocation at least the size of sizeof(unsigned long) so that
set_bit() and test_bit() have sufficient room for read/write operations
without overwriting unallocated memory.
[1] Link: https://lore.kernel.org/all/ZkNcALr3W3KGYYJG@gmail.com/ |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: Use variable length array instead of fixed size
Should fix smatch warning:
ntfs_set_label() error: __builtin_memcpy() 'uni->name' too small (20 vs 256) |
| In the Linux kernel, the following vulnerability has been resolved:
speakup: Fix sizeof() vs ARRAY_SIZE() bug
The "buf" pointer is an array of u16 values. This code should be
using ARRAY_SIZE() (which is 256) instead of sizeof() (which is 512),
otherwise it can the still got out of bounds. |
| In the Linux kernel, the following vulnerability has been resolved:
net: fix out-of-bounds access in ops_init
net_alloc_generic is called by net_alloc, which is called without any
locking. It reads max_gen_ptrs, which is changed under pernet_ops_rwsem. It
is read twice, first to allocate an array, then to set s.len, which is
later used to limit the bounds of the array access.
It is possible that the array is allocated and another thread is
registering a new pernet ops, increments max_gen_ptrs, which is then used
to set s.len with a larger than allocated length for the variable array.
Fix it by reading max_gen_ptrs only once in net_alloc_generic. If
max_gen_ptrs is later incremented, it will be caught in net_assign_generic. |
| In the Linux kernel, the following vulnerability has been resolved:
nouveau/uvmm: fix addr/range calcs for remap operations
dEQP-VK.sparse_resources.image_rebind.2d_array.r64i.128_128_8
was causing a remap operation like the below.
op_remap: prev: 0000003fffed0000 00000000000f0000 00000000a5abd18a 0000000000000000
op_remap: next:
op_remap: unmap: 0000003fffed0000 0000000000100000 0
op_map: map: 0000003ffffc0000 0000000000010000 000000005b1ba33c 00000000000e0000
This was resulting in an unmap operation from 0x3fffed0000+0xf0000, 0x100000
which was corrupting the pagetables and oopsing the kernel.
Fixes the prev + unmap range calcs to use start/end and map back to addr/range. |
