| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ebt_nflog: pin the NFLOG backend
nf_log_unregister() runs after the per-net teardown so its final RCU
grace period also drains readers that obtained the logger from a per-net
binding. However, ebt_nflog passes an explicit ULOG log type to
nf_log_packet() without holding a reference on the selected logger module,
unlike the xt_NFLOG and nft_log frontends.
An ebtables nflog rule can therefore remain callable while nfnetlink_log
is unloaded. The resulting interleaving is:
CPU 0 CPU 1
nfnetlink_log_fini()
unregister_pernet_subsys()
kfree(nfnl_log_pernet(net))
ebt_nflog_tg()
nf_log_packet()
nfulnl_log_packet()
instance_lookup_get_rcu()
The global ULOG logger is still registered at this point, so CPU 1
dereferences the per-net state after CPU 0 has freed it. KASAN reported:
BUG: KASAN: slab-use-after-free in instance_lookup_get_rcu
Read of size 8 at addr ff110001052e6210 by task poc/92
Call Trace:
instance_lookup_get_rcu+0x1ce/0x1f0 [nfnetlink_log]
nfulnl_log_packet+0x248/0x2fb0 [nfnetlink_log]
nf_log_packet+0x204/0x300
ebt_nflog_tg+0x351/0x550
ebt_do_table+0xedf/0x22b0
Allocated by task 90:
__kmalloc_noprof+0x186/0x470
ops_init+0x6d/0x420
register_pernet_operations+0x2f6/0x670
register_pernet_subsys+0x23/0x40
Freed by task 93:
kfree+0x131/0x3c0
ops_undo_list+0x3e3/0x700
unregister_pernet_operations+0x232/0x490
unregister_pernet_subsys+0x1c/0x30
nfnetlink_log_fini+0x34/0x450 [nfnetlink_log]
Acquire the ULOG logger module reference when an ebt_nflog rule is
validated and release it when the rule is destroyed. Request the NFLOG
backend for legacy callers when needed, matching xt_NFLOG. This prevents
module teardown until all ebt_nflog rules have stopped using the logger. |
| In the Linux kernel, the following vulnerability has been resolved:
net/packet: reset the MAC header on the packet-socket transmit path
packet_parse_headers() resets the MAC header only for a SOCK_RAW frame
whose socket did not bind a protocol. A protocol-bound SOCK_RAW socket,
any SOCK_DGRAM frame, and the legacy SOCK_PACKET path therefore leave
skb->mac_header unset here.
For frames sent via __dev_queue_xmit() this is harmless: it resets the
MAC header unconditionally. But the packet-socket PACKET_QDISC_BYPASS
path uses dev_direct_xmit(), which does not, so the frame reaches
ndo_start_xmit() with the MAC header unset. A driver that reads
eth_hdr(skb) on transmit then dereferences skb->head + (u16)~0, an
out-of-bounds access ~64 KiB past the head -- the same class fixed for
one consumer in commit f5089008f90c ("macsec: do not read an unset MAC
header in macsec_encrypt()").
packet_parse_headers() runs only on the transmit path, where skb->data
points at the start of the L2 header for every packet-socket type
regardless of its length: SOCK_RAW and SOCK_PACKET carry a user-supplied
header and SOCK_DGRAM has one built by dev_hard_header(). Reset the MAC
header unconditionally, mirroring __dev_queue_xmit(), so the frame is
anchored on the bypass path too.
Found by 0sec (https://0sec.ai) using automated source analysis;
verified against source and matched to the macsec KASAN report in
f5089008f90c. Compile-tested. |
| A flaw was found in GnuTLS. The `gnutls_pkcs11_token_set_pin` function, used for changing the Security Officer PIN, can lead to a use-after-free vulnerability. This occurs when an attacker attempts to change the PIN with a NULL old PIN for a token that lacks a protected authentication path. |
| A flaw was found in p11-kit. A remote attacker could exploit this vulnerability by calling the C_DeriveKey function on a remote token with specific IBM kyber or IBM btc derive mechanism parameters set to NULL. This could lead to the RPC-client attempting to return an uninitialized value, potentially resulting in a NULL dereference or undefined behavior. This issue may cause an application level denial of service or other unpredictable system states. |
| A use-after-free vulnerability was found in libxslt while parsing xsl nodes that may lead to the dereference of expired pointers and application crash. |
| In the Linux kernel, the following vulnerability has been resolved:
ovpn: skip rehash for peers already removed from by_id
ovpn_nl_peer_set_doit() resolves the target peer via
ovpn_peer_get_by_id() before taking ovpn->lock. In the window between
the lookup (which only takes a refcount) and the subsequent
spin_lock_bh(&ovpn->lock), a concurrent OVPN_CMD_PEER_DEL, keepalive
expiry, or socket teardown can take ovpn->lock first, run
ovpn_peer_remove() to unhash the peer from all four tables (by_id,
by_vpn_addr4/6, by_transp_addr) and release the lock. set_doit then
acquires ovpn->lock and calls ovpn_peer_hash_vpn_ip(), which
re-inserts the now-removed peer back into the rehashing tables.
The same race affects the float path: ovpn_peer_endpoints_update()
holds only a refcount and acquires ovpn->lock very late (after async
AEAD decrypt and a netlink notification), then rehashes the peer
in the by_transp_addr table.
The resurrected peer becomes reachable again from the RX lookup
(ovpn_peer_get_by_transp_addr) and the TX VPN-IP lookup, even though
userspace believes it is gone. Once the data-path refcount drops the
peer is freed via call_rcu while the hash entries embedded in it
remain linked, opening a UAF window.
Bail out of the rehash when hash_entry_id is unhashed, mirroring
the sentinel already used by ovpn_peer_remove() to detect the
already-removed state. The check is safe under ovpn->lock, which
serializes every mutation of hash_entry_id, and is a no-op for the
add path because ovpn_peer_add_mp() inserts hash_entry_id before
calling ovpn_peer_hash_vpn_ip(). |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: do not arm the ageing timer on a device that is down
vxlan_changelink() arms vxlan->age_timer whenever the requested ageing
interval differs from the configured one:
if (conf.age_interval != vxlan->cfg.age_interval)
mod_timer(&vxlan->age_timer, jiffies);
There is no netif_running() test, so the timer is armed even on a device
that was never brought up. The only synchronous cancel in the driver is
the timer_delete_sync() in vxlan_stop(), which is .ndo_stop.
netif_close_many() drops devices without IFF_UP before
__dev_close_many() runs, so that cancel is skipped for such a device.
vxlan_setup() sets dev->needs_free_netdev = true and age_timer is a
member of struct vxlan_dev, so free_netdev() releases the allocation the
timer lives in while it is still queued on a timer_base.
expire_timers() unlinks the entry before it loads timer->function, so
the timer core writes through the freed object's list pointers:
BUG: KASAN: slab-use-after-free in __run_timers+0x208/0x654
Write of size 8 at addr ffff00001adace68 by task true/192
__asan_store8+0x84/0xac
__run_timers+0x208/0x654
run_timer_softirq+0x154/0x18c
Allocated by task 189:
alloc_netdev_mqs+0x64/0x720
rtnl_create_link+0x4ac/0x520
rtnl_newlink+0x758/0xd00
Freed by task 191:
netdev_release+0x40/0x58
netdev_run_todo+0x4a4/0x8c0
rtnl_dellink+0x200/0x4e8
The rtnl operations involved are netns-scoped, so an unprivileged user
can perform them in a new user and network namespace.
Arming the timer on a down device never had an effect: vxlan_cleanup()
returns early on !netif_running(), and vxlan_open() arms the timer for
any non-zero interval once the device is brought up. Add the missing
test.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> |
| In the Linux kernel, the following vulnerability has been resolved:
mac802154: fix netdev use-after-free in beacon worker
mac802154_beacon_worker() reads local->beacon_req under RCU and derives
the sub-interface from the request, but then drops the RCU read lock and
continues to use both sdata and the embedded wpan_dev.
mac802154_stop_beacons_locked() cancels only pending beacon work, clears
local->beacon_req and frees the request. A beacon worker that is already
running can therefore continue after interface teardown and dereference
the freed netdev private area.
The scan worker already pins the netdev before leaving RCU. Apply the
same lifetime rule to the beacon worker: take a netdev reference while
the request is still protected by RCU, and release it on all paths that
continue after the reference is acquired. |
| In the Linux kernel, the following vulnerability has been resolved:
eventfs: Fix use-after-free in eventfs_remove_rec()
eventfs_remove_rec() recursively removes the child at the current loop
position. After the recursive call returns, list_for_each_entry() advances
by reading list.next from the removed child.
If free_ei() drops the final reference, release_ei() reuses the list/rcu
union to queue an SRCU callback. The child may be freed before that read.
The eventfs_mutex serializes list updates, but it does not keep the removed
child alive or prevent the SRCU callback from running.
Use list_for_each_entry_safe() to save the next sibling before recursively
removing the current child. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: keep chunk->transport in step with the list it is queued on
__sctp_outq_flush_rtx() moves a gap-acked chunk onto another transport's
transmitted list without updating chunk->transport:
if (chunk->tsn_gap_acked) {
list_move_tail(&chunk->transmitted_list,
&transport->transmitted);
continue;
}
The chunk then sits on a live transport's list while chunk->transport still
names a different one. If that transport is removed - sctp_assoc_rm_peer()
from an ASCONF Delete-IP - sctp_transport_free() RCU-frees it and the chunk
is left with a dangling pointer. sctp_assoc_rm_peer() scrubs
peer->transmitted and asoc->outqueue.out_chunk_list, but the chunk is on
neither.
The pointer is not followed while tsn_gap_acked is set. A SACK that
reneges on the TSN clears the flag, and the next SACK reaches
tchunk->transport->flight_size -= sctp_data_size(tchunk);
inside the freed transport. KASAN reports a slab-use-after-free read in
sctp_check_transmitted(), freed from sctp_assoc_rm_peer(). Both the
removal and the SACKs come from the association peer.
Set chunk->transport at the move. The ordinary resend path needs nothing:
it reaches its list_move_tail() only after sctp_packet_append_chunk()
returned SCTP_XMIT_OK, and __sctp_packet_append_chunk() has rebound the
chunk by then.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: cls_route: fix fastmap use-after-free on filter
The route4 classifier maintains a 16-slot fastmap cache that stores raw
struct route4_filter pointers indexed by (id, iif). The reader
(route4_classify) populates this cache via route4_set_fastmap() for every
classified packet that hits a filter. The writer (route4_delete,
route4_change) clears the cache via route4_reset_fastmap() before
RCU-deferred kfree of the filter.
This creates a UAF race:
1. Reader walks the RCU-protected bucket chain, finds filter f
2. Writer unlinks f, calls route4_reset_fastmap(), then tcf_queue_work()
3. Reader calls route4_set_fastmap() and writes f into the cache
*after* the writer's reset, caching a pointer about to be freed
4. After the RCU grace period, kfree(f) executes
5. Next classified packet on the same (id, iif) tuple hits the stale
fastmap entry and reads f->res from freed memory
Reproduced with an mdelay(100) accelerator in route4_set_fastmap() and a
concurrent add/delete stress test (provided by both zdi and Santosh).
Both triggered KASAN slab-use-after-free reports in the route4 fastmap
paths.
Fix:
Introduce a per-filter boolean dying flag to suppress stale fastmap
republishing by in-flight readers. |
| In the Linux kernel, the following vulnerability has been resolved:
vhost: reset the vring metadata cache on vring reconfiguration
vq->meta_iotlb[] caches the vhost_iotlb_map that backs each vring
metadata region, and iotlb_access_ok() returns early on a cache hit,
taking the hit as proof that the region has already been validated:
if (vhost_vq_meta_fetch(vq, addr, len, type))
return true;
The cache is reset on VHOST_IOTLB_UPDATE and VHOST_IOTLB_INVALIDATE, on
device IOTLB (re)initialisation and on vq reset, but not when
VHOST_SET_VRING_ADDR replaces vq->desc, vq->avail and vq->used, nor when
VHOST_SET_VRING_NUM changes the region sizes.
With a device IOTLB attached both ioctls are accepted while the vq is
live, and neither validates the addresses at ioctl time: vq_access_ok()
and vq_log_used_access_ok() return true early because the addresses are
GIOVAs, deferring validation to prefetch time. Once the cache has been
populated that deferred validation no longer runs -- vq_meta_prefetch()
hits the stale entry and returns true -- and vhost_vq_meta_fetch() keeps
translating through the old mapping as
map->addr + addr - map->start
for an address the mapping no longer covers. vhost_copy_to_user() and
vhost_copy_from_user() consume the result with __copy_to_user() and
__copy_from_user(), which do not check it either, so a subsequent used
ring update or descriptor fetch accesses memory outside the region the
IOTLB actually maps.
Reset the metadata cache whenever the vring is reconfigured, so the new
addresses are pushed back through iotlb_access_ok()'s slow path. |
| When a BIG-IP is configured with DNS caching (Such as a DNS profile with caching enabled, SSL Orchestrator, Advanced WAF DoS protection), undisclosed traffic can cause the Traffic Management Microkernel (TMM) to terminate. Note: Software versions which have reached End of Technical Support (EoTS) are not evaluated. |
| PDFio before 1.6.5 contains a dangling pointer vulnerability in the dictionary string-formatting function that stores a pointer to a stack-local buffer in the document dictionary without copying the string value. In multi-threaded or pooled-request environments, attackers or concurrent users can trigger stack memory reuse across requests, causing cross-tenant document content corruption by silently overwriting one caller's dictionary string values with another caller's data. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: ipheth: fix carrier_work UAF on disconnect
ipheth_sndbulk_callback() re-arms the carrier-check work on any
non-zero URB status:
else
schedule_delayed_work(&dev->carrier_work, 0);
Nothing ties that to the interface being up, so the work can be armed
again after ipheth_close() has already drained it, and stay armed
until the netdev whose private area embeds it is freed.
On unplug with a TX URB in flight, ipheth_disconnect() drains the work
through unregister_netdev() -> ipheth_close() ->
cancel_delayed_work_sync() and only then calls ipheth_kill_urbs().
usb_kill_urb() completes the in-flight TX URB with -ENOENT, so
ipheth_sndbulk_callback() runs after the drain and re-arms
carrier_work.
The same completion also re-arms the work if the interface is only
brought down while a TX URB is in flight, and
ipheth_carrier_check_work() then keeps re-queueing itself once a
second. unregister_netdev() does not call ipheth_close() for an
already-down interface, so nothing drains it on the later unplug
either.
In both cases free_netdev() frees the netdev while carrier_work is
still pending, and ipheth_carrier_check_work() dereferences freed
memory.
Tie the work to the interface state instead of chasing the completion:
disable it in ipheth_close() and enable it in ipheth_open(), so a
schedule_delayed_work() from the URB completion is a no-op whenever
the interface is not up. disable_delayed_work_sync() also waits for a
running instance, so it fully replaces the cancel_delayed_work_sync()
it takes the place of. The work starts out disabled in ipheth_probe()
so the enable/disable counts balance from the first open.
Reproduced under KASAN on linux-next (next-20260731) with dummy_hcd and
raw-gadget standing in for the device, driving the second path above (the
interface is already down, so unregister_netdev() does not call
ipheth_close()): 15 of 15 unpatched boots report a slab-use-after-free in
__run_timers(), freed by ipheth_disconnect() and re-armed from
ipheth_sndbulk_callback() via queue_delayed_work_on(). The
same trigger on a kernel differing only by this patch reports 0 of 15,
and the carrier check still functions across open/close cycles.
The reproducer needs an attached USB device that stops draining bulk OUT,
plus a link down and unplug, driven as root. It is not a privilege
boundary crossing and no exploit primitive was developed.
Found by 0sec (https://0sec.ai). |
| A use-after-free vulnerability was found in libxml2. This issue occurs when parsing XPath elements under certain circumstances when the XML schematron has the <sch:name path="..."/> schema elements. This flaw allows a malicious actor to craft a malicious XML document used as input for libxml, resulting in the program's crash using libxml or other possible undefined behaviors. |
| Internally found bugs present in Firefox 153. Some of these bugs showed evidence of memory corruption or another security-relevant defect and we presume that with enough effort some of these could have been exploited. This vulnerability was fixed in Firefox 154 and Thunderbird 154. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: mgmt: fix UAF in pair command cancellation
The pairing completion and authentication failure callbacks look up the
pending MGMT_OP_PAIR_DEVICE command by walking hdev->mgmt_pending. The
lookup returned a command that was still linked on the shared pending list,
without keeping mgmt_pending_lock held for the later dereference and
removal.
A concurrent MGMT_OP_CANCEL_PAIR_DEVICE request can remove and free the
same pending command before the callback uses it. The reverse race is also
possible when cancel_pair_device() gets a command from pending_find() and a
callback removes it before the cancel path dereferences it. This can lead
to a use-after-free and a second list_del().
Make the pairing lookup helpers transfer ownership of the pending command
by removing it from hdev->mgmt_pending while holding mgmt_pending_lock.
The callbacks and cancel path then complete the command and free it
directly, so racing paths cannot find or free the same command again. Take
a temporary hci_conn reference in cancel_pair_device() because the command
completion drops the reference stored in the pending command. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/pm: fix pptable use-after-free
amdgpu_dpm_get_pp_table() returns a pointer to a driver-owned power table
after dropping adev->pm.mutex. The sysfs path then copies from that pointer.
A concurrent pp_table write can replace and free the allocation during the
copy, causing a use-after-free.
Change the DPM interface to copy into caller-provided storage while the mutex
is held. Keep the size-only query for attribute discovery without exposing
the driver-owned pointer.
(cherry picked from commit f6eed7acfd30099ef7baeb6ba45bb59daad80631) |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: ucsi: Fix race condition and ordering in port unregistration
A synchronization issue exists during port unregistration where pending
partner work items can race against workqueue destruction, leading to
use-after-free conditions:
cros_ec_ucsi cros_ec_ucsi.3.auto: error -ETIMEDOUT: PPM init failed
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:__queue_work+0x83/0x4a0
Call Trace:
<IRQ>
__cfi_delayed_work_timer_fn+0x10/0x10
run_timer_softirq+0x3b6/0xbd0
sched_clock_cpu+0xc/0x110
irq_exit_rcu+0x18d/0x330
fred_sysvec_apic_timer_interrupt+0x5e/0x80
Fix this by ensuring strict ordering and proper serialization during
teardown:
1. Move ucsi_unregister_partner() to the beginning of the teardown
sequence and protect it under the connector mutex lock.
2. Ensure all pending partner tasks are explicitly flushed and finished
before the workqueue is destroyed.
3. Switch from mod_delayed_work() to a cancel_delayed_work() and
queue_delayed_work() sequence. This guarantees that items currently marked
as pending won't be scheduled an additional time, preventing a double
release of resources which leads to the following crash:
Oops: general protection fault, probably for non-canonical address
0xdead000000000122: 0000 [#1] SMP NOPTI
Workqueue: cros_ec_ucsi.3.auto-con2 ucsi_poll_worker
RIP: 0010:ucsi_poll_worker+0x65/0x1e0
Call Trace:
<TASK>
process_scheduled_works+0x218/0x6d0
worker_thread+0x188/0x3f0
__cfi_worker_thread+0x10/0x10
kthread+0x226/0x2a0
To ensure these rules are applied identically across both the normal
teardown and the ucsi_init() error paths, consolidate the cleanup logic
into a new helper, ucsi_unregister_port(). |
