| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
MIPS: cevt-r4k: Don't call get_c0_compare_int if timer irq is installed
This avoids warning:
[ 0.118053] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:283
Caused by get_c0_compare_int on secondary CPU.
We also skipped saving IRQ number to struct clock_event_device *cd as
it's never used by clockevent core, as per comments it's only meant
for "non CPU local devices". |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qedi: Fix crash while reading debugfs attribute
The qedi_dbg_do_not_recover_cmd_read() function invokes sprintf() directly
on a __user pointer, which results into the crash.
To fix this issue, use a small local stack buffer for sprintf() and then
call simple_read_from_buffer(), which in turns make the copy_to_user()
call.
BUG: unable to handle page fault for address: 00007f4801111000
PGD 8000000864df6067 P4D 8000000864df6067 PUD 864df7067 PMD 846028067 PTE 0
Oops: 0002 [#1] PREEMPT SMP PTI
Hardware name: HPE ProLiant DL380 Gen10/ProLiant DL380 Gen10, BIOS U30 06/15/2023
RIP: 0010:memcpy_orig+0xcd/0x130
RSP: 0018:ffffb7a18c3ffc40 EFLAGS: 00010202
RAX: 00007f4801111000 RBX: 00007f4801111000 RCX: 000000000000000f
RDX: 000000000000000f RSI: ffffffffc0bfd7a0 RDI: 00007f4801111000
RBP: ffffffffc0bfd7a0 R08: 725f746f6e5f6f64 R09: 3d7265766f636572
R10: ffffb7a18c3ffd08 R11: 0000000000000000 R12: 00007f4881110fff
R13: 000000007fffffff R14: ffffb7a18c3ffca0 R15: ffffffffc0bfd7af
FS: 00007f480118a740(0000) GS:ffff98e38af00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f4801111000 CR3: 0000000864b8e001 CR4: 00000000007706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
? __die_body+0x1a/0x60
? page_fault_oops+0x183/0x510
? exc_page_fault+0x69/0x150
? asm_exc_page_fault+0x22/0x30
? memcpy_orig+0xcd/0x130
vsnprintf+0x102/0x4c0
sprintf+0x51/0x80
qedi_dbg_do_not_recover_cmd_read+0x2f/0x50 [qedi 6bcfdeeecdea037da47069eca2ba717c84a77324]
full_proxy_read+0x50/0x80
vfs_read+0xa5/0x2e0
? folio_add_new_anon_rmap+0x44/0xa0
? set_pte_at+0x15/0x30
? do_pte_missing+0x426/0x7f0
ksys_read+0xa5/0xe0
do_syscall_64+0x58/0x80
? __count_memcg_events+0x46/0x90
? count_memcg_event_mm+0x3d/0x60
? handle_mm_fault+0x196/0x2f0
? do_user_addr_fault+0x267/0x890
? exc_page_fault+0x69/0x150
entry_SYSCALL_64_after_hwframe+0x72/0xdc
RIP: 0033:0x7f4800f20b4d |
| n8n is an open source workflow automation platform. Versions 0.123.1 through 1.119.1 do not have adequate protections to prevent RCE through the project's pre-commit hooks. The Add Config operation allows workflows to set arbitrary Git configuration values, including core.hooksPath, which can point to a malicious Git hook that executes arbitrary commands on the n8n host during subsequent Git operations. Exploitation requires the ability to create or modify an n8n workflow using the Git node. This issue is fixed in version 1.119.2. Workarounds include excluding the Git Node (Docs) and avoiding cloning or interacting with untrusted repositories using the Git Node. |
| In AzeoTech DAQFactory release 20.7 (Build 2555), an Access of Uninitialized Pointer vulnerability can be exploited by an attacker which can lead to arbitrary code execution. |
| FACTION is a PenTesting Report Generation and Collaboration Framework. Prior to version 1.7.1, an extension execution path in Faction’s extension framework permits untrusted extension code to execute arbitrary system commands on the server when a lifecycle hook is invoked, resulting in remote code execution (RCE) on the host running Faction. Due to a missing authentication check on the /portal/AppStoreDashboard endpoint, an attacker can access the extension management UI and upload a malicious extension without any authentication, making this vulnerability exploitable by unauthenticated users. This issue has been patched in version 1.7.1. |
| The Static Asset API in Mintlify Platform before 2025-11-15 allows remote attackers to inject arbitrary web script or HTML via the subdomain parameter because any tenant's assets can be served on any other tenant's documentation site. |
| n8n is an open source workflow automation platform. Prior to 1.113.0, a remote code execution vulnerability exists in the Git Node component available in both Cloud and Self-Hosted versions of n8n. When a malicious actor clones a remote repository containing a pre-commit hook, the subsequent use of the Commit operation in the Git Node can inadvertently trigger the hook’s execution. This allows attackers to execute arbitrary code within the n8n environment, potentially compromising the system and any connected credentials or workflows. This vulnerability is fixed in 1.113.0. |
| A maliciously crafted STP file in ASMKERN228A.dll when parsed through Autodesk applications can be used to dereference an untrusted pointer. This vulnerability, along with other vulnerabilities, could lead to code execution in the current process. |
| Information disclosure while processing system calls with invalid parameters. |
| In the Linux kernel, the following vulnerability has been resolved:
netrom: Fix data-races around sysctl_net_busy_read
We need to protect the reader reading the sysctl value because the
value can be changed concurrently. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: core: Fix hang in usb_kill_urb by adding memory barriers
The syzbot fuzzer has identified a bug in which processes hang waiting
for usb_kill_urb() to return. It turns out the issue is not unlinking
the URB; that works just fine. Rather, the problem arises when the
wakeup notification that the URB has completed is not received.
The reason is memory-access ordering on SMP systems. In outline form,
usb_kill_urb() and __usb_hcd_giveback_urb() operating concurrently on
different CPUs perform the following actions:
CPU 0 CPU 1
---------------------------- ---------------------------------
usb_kill_urb(): __usb_hcd_giveback_urb():
... ...
atomic_inc(&urb->reject); atomic_dec(&urb->use_count);
... ...
wait_event(usb_kill_urb_queue,
atomic_read(&urb->use_count) == 0);
if (atomic_read(&urb->reject))
wake_up(&usb_kill_urb_queue);
Confining your attention to urb->reject and urb->use_count, you can
see that the overall pattern of accesses on CPU 0 is:
write urb->reject, then read urb->use_count;
whereas the overall pattern of accesses on CPU 1 is:
write urb->use_count, then read urb->reject.
This pattern is referred to in memory-model circles as SB (for "Store
Buffering"), and it is well known that without suitable enforcement of
the desired order of accesses -- in the form of memory barriers -- it
is entirely possible for one or both CPUs to execute their reads ahead
of their writes. The end result will be that sometimes CPU 0 sees the
old un-decremented value of urb->use_count while CPU 1 sees the old
un-incremented value of urb->reject. Consequently CPU 0 ends up on
the wait queue and never gets woken up, leading to the observed hang
in usb_kill_urb().
The same pattern of accesses occurs in usb_poison_urb() and the
failure pathway of usb_hcd_submit_urb().
The problem is fixed by adding suitable memory barriers. To provide
proper memory-access ordering in the SB pattern, a full barrier is
required on both CPUs. The atomic_inc() and atomic_dec() accesses
themselves don't provide any memory ordering, but since they are
present, we can use the optimized smp_mb__after_atomic() memory
barrier in the various routines to obtain the desired effect.
This patch adds the necessary memory barriers. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: mxs-auart: add spinlock around changing cts state
The uart_handle_cts_change() function in serial_core expects the caller
to hold uport->lock. For example, I have seen the below kernel splat,
when the Bluetooth driver is loaded on an i.MX28 board.
[ 85.119255] ------------[ cut here ]------------
[ 85.124413] WARNING: CPU: 0 PID: 27 at /drivers/tty/serial/serial_core.c:3453 uart_handle_cts_change+0xb4/0xec
[ 85.134694] Modules linked in: hci_uart bluetooth ecdh_generic ecc wlcore_sdio configfs
[ 85.143314] CPU: 0 PID: 27 Comm: kworker/u3:0 Not tainted 6.6.3-00021-gd62a2f068f92 #1
[ 85.151396] Hardware name: Freescale MXS (Device Tree)
[ 85.156679] Workqueue: hci0 hci_power_on [bluetooth]
(...)
[ 85.191765] uart_handle_cts_change from mxs_auart_irq_handle+0x380/0x3f4
[ 85.198787] mxs_auart_irq_handle from __handle_irq_event_percpu+0x88/0x210
(...) |
| An issue was discovered in Tiny Tiny RSS (aka tt-rss) before 2020-09-16. imgproxy in plugins/af_proxy_http/init.php mishandles $_REQUEST["url"] in an error message. |
| In JetBrains TeamCity before 2025.11 maven embedder allowed loading extensions via project configuration |
| Navigations were being allowed when dragging a URL from a cross-origin iframe into the same tab which could lead to website spoofing attacks This vulnerability affects Firefox < 109, Firefox ESR < 102.7, and Thunderbird < 102.7. |
| In the Linux kernel, the following vulnerability has been resolved:
xhci: Fix command ring pointer corruption while aborting a command
The command ring pointer is located at [6:63] bits of the command
ring control register (CRCR). All the control bits like command stop,
abort are located at [0:3] bits. While aborting a command, we read the
CRCR and set the abort bit and write to the CRCR. The read will always
give command ring pointer as all zeros. So we essentially write only
the control bits. Since we split the 64 bit write into two 32 bit writes,
there is a possibility of xHC command ring stopped before the upper
dword (all zeros) is written. If that happens, xHC updates the upper
dword of its internal command ring pointer with all zeros. Next time,
when the command ring is restarted, we see xHC memory access failures.
Fix this issue by only writing to the lower dword of CRCR where all
control bits are located. |
| In the Linux kernel, the following vulnerability has been resolved:
dm btree remove: assign new_root only when removal succeeds
remove_raw() in dm_btree_remove() may fail due to IO read error
(e.g. read the content of origin block fails during shadowing),
and the value of shadow_spine::root is uninitialized, but
the uninitialized value is still assign to new_root in the
end of dm_btree_remove().
For dm-thin, the value of pmd->details_root or pmd->root will become
an uninitialized value, so if trying to read details_info tree again
out-of-bound memory may occur as showed below:
general protection fault, probably for non-canonical address 0x3fdcb14c8d7520
CPU: 4 PID: 515 Comm: dmsetup Not tainted 5.13.0-rc6
Hardware name: QEMU Standard PC
RIP: 0010:metadata_ll_load_ie+0x14/0x30
Call Trace:
sm_metadata_count_is_more_than_one+0xb9/0xe0
dm_tm_shadow_block+0x52/0x1c0
shadow_step+0x59/0xf0
remove_raw+0xb2/0x170
dm_btree_remove+0xf4/0x1c0
dm_pool_delete_thin_device+0xc3/0x140
pool_message+0x218/0x2b0
target_message+0x251/0x290
ctl_ioctl+0x1c4/0x4d0
dm_ctl_ioctl+0xe/0x20
__x64_sys_ioctl+0x7b/0xb0
do_syscall_64+0x40/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixing it by only assign new_root when removal succeeds |
| Microsoft Streaming Service Elevation of Privilege Vulnerability |
| Windows Kernel-Mode Driver Elevation of Privilege Vulnerability |
| In the Linux kernel, the following vulnerability has been resolved:
module: ensure that kobject_put() is safe for module type kobjects
In 'lookup_or_create_module_kobject()', an internal kobject is created
using 'module_ktype'. So call to 'kobject_put()' on error handling
path causes an attempt to use an uninitialized completion pointer in
'module_kobject_release()'. In this scenario, we just want to release
kobject without an extra synchronization required for a regular module
unloading process, so adding an extra check whether 'complete()' is
actually required makes 'kobject_put()' safe. |
