| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: pch: use raw_spinlock_t for the register lock
pch_irq_type() is registered as the irq_chip .irq_set_type callback and
takes chip->spinlock with spin_lock_irqsave(). This callback is reached
from __setup_irq() -> __irq_set_trigger() -> chip->irq_set_type() while
the caller holds desc->lock, a raw_spinlock_t, with hardirqs disabled.
That context is not sleepable, but on PREEMPT_RT a regular spinlock_t is
an rtmutex-backed sleeping lock, so acquiring it there is invalid.
This was confirmed on a PREEMPT_RT kernel with lockdep
(PROVE_RAW_LOCK_NESTING and DEBUG_ATOMIC_SLEEP). A grounded PoC mirrored
pch_irq_type()'s locking and drove it through the real genirq carrier
irq_set_irq_type() -> __irq_set_trigger() -> chip->irq_set_type(), i.e.
the same __irq_set_trigger() edge that __setup_irq() takes for a
requested IRQ. With the original spin_lock_irqsave() edge lockdep
reported an invalid wait context, immediately followed by:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 95, name: insmod
hardirqs last disabled at (3784): _raw_spin_lock_irqsave+0x4f/0x60
rt_spin_lock+0x3a/0x1c0
repro_irq_set_type+0x64/0xa0 [pch_repro]
__irq_set_trigger+0x69/0x140
irq_set_irq_type+0x78/0xd0
Switching the mirrored lock to raw_spinlock_t made both splats go away.
Convert the register lock to raw_spinlock_t. The same lock also
serializes the GPIO direction/value callbacks and the suspend/resume
register save/restore, but all of those critical sections only perform
MMIO register accesses (ioread32()/iowrite32()) and
irq_set_handler_locked(); none of them contain sleepable operations.
Keeping this register lock non-sleeping is therefore appropriate for the
irqchip callbacks and does not change the GPIO-side locking contract.
This is the same class of issue and fix as recently addressed for other
GPIO controllers, e.g. commit 286533cb14a3 ("gpio: sch: use raw_spinlock_t
in the irq startup path") and commit 90f0109019e6 ("gpio: eic-sprd: use
raw_spinlock_t in the irq startup path"). |
| In the Linux kernel, the following vulnerability has been resolved:
s390/qeth: Check CAP_NET_ADMIN for private ioctls
Gate the SIOCDEVPRIVATE ioctl commands SIOC_QETH_ADP_SET_SNMP_CONTROL,
SIOC_QETH_GET_CARD_TYPE and SIOC_QETH_QUERY_OAT with CAP_NET_ADMIN
capable check to ensure unprivileged users cannot invoke them. |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: fix potential UAF on meter attach failure
While attaching a newly created meter attach_meter() function makes
the new meter visible to other CPUs but can still fail afterwards.
On failure, it detaches the meter back and returns an error.
However, this is an unexpected behavior for the ovs_meter_cmd_set()
that uses a plain kfree(meter) on attach failure without waiting for
RCU readers to stop using it, assuming it was never visible.
This is never a problem for ovs-vswitchd as it always creates meters
before creating any flows that use them. But the UAF can be triggered
with a custom application using uAPI:
BUG: KASAN: slab-use-after-free in ovs_meter_execute (net/openvswitch/meter.c:653)
Read of size 8 at addr ffff88810d152650 by task meter/2508
Call Trace:
ovs_meter_execute (net/openvswitch/meter.c:653)
do_execute_actions (net/openvswitch/actions.c:1407)
ovs_execute_actions (net/openvswitch/actions.c:1584)
ovs_packet_cmd_execute (net/openvswitch/datapath.c:703)
...
netlink_sendmsg (af_netlink.c:1900)
Allocated by task 2519:
__kasan_kmalloc (mm/kasan/common.c:398 mm/kasan/common.c:415)
ovs_meter_cmd_set (net/openvswitch/meter.c:422)
...
netlink_sendmsg (af_netlink.c:1900)
Freed by task 2519:
kfree (mm/slub.c:2705 mm/slub.c:6405 mm/slub.c:6720)
ovs_meter_cmd_set (net/openvswitch/meter.c:479)
...
netlink_sendmsg (af_netlink.c:1900)
Fix that by making sure attach_meter() doesn't make the meter visible
until all the checks are done and the function can't fail anymore.
This also makes sure the "hash" value is calculated after the potential
re-sizing of the table.
Reported by Trend Micro's Zero Day Initiative as ZDI-CAN-31642. |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: fix skb leak on flow key update failure during ct
ovs_ct_execute() always steals or frees the skb on failure while
ovs_flow_key_update() does not. So, if it fails and we return right
away, the skb ends up leaked.
Fix that by breaking instead and letting the common error handling
code at the bottom of the loop to free the skb properly.
This is a very unlikely scenario as it requires the packet to become
unparseable by applying a set of actions on a previously parseable skb,
but should be fixed nevertheless.
Reported by Sashiko. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to bypass security restrictions due to improper validation of user-controlled addresses. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: jz4780: Cache host clock rate at probe to prevent CCF prepare_lock deadlock
Fix a severe AB/BA deadlock between the Common Clock Framework (CCF)
and the I2C adapter lock, which triggers when an I2C-controlled clock
generator client (like the Si5351) is registered or modified under the CCF.
During an i2c client clock (generator) frequency change, the CCF acquires its global
'prepare_lock' mutex and the driver calls i2c_transfer() to update the client's
chip registers, stalling for the adapter's I2C bus lock.
Concurrently, an independent, parallel transfer on the same bus (e.g., a GPIO
expander handling LEDs) can hold the I2C adapter lock. Inside this parallel
transfer path, jz4780_i2c_set_speed() calls clk_get_rate() on the host
controller's input clock to calculate bus timings. This call attempts to acquire
the blocked CCF 'prepare_lock', creating a circular dependency that freezes
the system.
The jz4780 host controller clock itself is static and never changes at runtime.
However, calling clk_get_rate() inside the active transfer path introduces
an unnecessary dependency on the CCF internal locks.
Eliminate this synchronous clk_get_rate() call from the active transfer
path by caching the static host peripheral clock rate once - inside the private
jz4780_i2c structure during jz4780_i2c_probe(). Update jz4780_i2c_set_speed()
to use this cached value, safely decoupling active I2C transactions from the
CCF internal locks without any risk of stale timings.
Assisted-by web based Google AI (pinpointing the bug and writing the message). |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: imx: Cancel hrtimer before clearing slave pointer
In i2c_imx_unreg_slave(), the slave pointer is set to NULL after
disabling interrupts. However, a pending interrupt might already
have started the hrtimer (i2c_imx_slave_timeout) before the pointer
was cleared. If the hrtimer fires after i2c_imx->slave is set to
NULL, the timer callback i2c_imx_slave_finish_op() will call
i2c_imx_slave_event() with a NULL slave pointer, which results in a
use-after-free / NULL pointer dereference.
Fix by canceling the hrtimer and waiting for it to complete after
disabling interrupts, before clearing the slave pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
can: ems_usb: validate CPC message lengths
ems_usb_read_bulk_callback() walks CPC messages packed in one USB
receive buffer.
Check that each declared message fits in the URB payload. Also require the
type-specific payload to cover the fields used by the CAN, state, error and
overrun handlers. |
| In the Linux kernel, the following vulnerability has been resolved:
can: etas_es58x: es58x_read_bulk_callback(): fix RX buffer leak on URB resubmit failure
es58x_read_bulk_callback() resubmits the RX URB after processing a received
packet. If the resubmit succeeds, the URB remains anchored and will be
handled by the normal RX path or by teardown.
However, if usb_submit_urb() fails, the callback unanchors the URB and then
returns directly. This skips the existing free_urb path, so the coherent
transfer buffer allocated with usb_alloc_coherent() is not released.
Reuse the existing free_urb path after a resubmit failure so that the RX
coherent buffer is freed before leaving the callback. |
| In the Linux kernel, the following vulnerability has been resolved:
can: kvaser_usb_leaf: kvaser_usb_leaf_wait_cmd(): validate received command extents
The wait and bulk receive paths walk variable-length commands from a
USB buffer. A nonzero command shorter than CMD_HEADER_LEN can still be
dispatched, and the wait path copies a matching command into a fixed
caller-owned struct kvaser_cmd using the device-provided length.
Reject nonzero commands that do not contain the fixed header or that
extend beyond the current USB buffer item. In the wait path, also reject
a matching command that exceeds the destination before copying it. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to cause a denial of service due to an improper buffer write. |
| In the Linux kernel, the following vulnerability has been resolved:
can: peak_usb: add bounds check for USB channel index
The channel control index ctrl_idx is derived from rx->len which comes
directly from a device USB payload. The mask 0x0f allows values 0-15, but
the array size of usb_if->dev[] is only 2. Values 2-15 cause heap
out-of-bounds read, eventually causing kernel panic in the IRQ context.
Add bounds checking for ctrl_idx before the array access in both
pcan_usb_pro_handle_canmsg() and pcan_usb_pro_handle_error(). |
| In the Linux kernel, the following vulnerability has been resolved:
can: peak_usb: peak_usb_start(): fix double free of transfer buffer on URB submit error
In peak_usb_start(), each RX URB transfer buffer is allocated with kmalloc()
and the URB is flagged URB_FREE_BUFFER so that the final usb_free_urb() also
frees the transfer buffer.
If usb_submit_urb() fails, the error path frees the buffer explicitly with
kfree(buf) and then calls usb_free_urb(urb). Because URB_FREE_BUFFER is set,
usb_free_urb() -> urb_destroy() frees the same buffer a second time, a double
free of the transfer buffer.
BUG: KASAN: double-free in usb_free_urb.part.0+0x91/0xb0
Free of addr ffff8881069ccb80 by task trigger.sh/285
Call Trace:
kfree+0x113/0x3c0
usb_free_urb.part.0+0x91/0xb0
Drop the redundant kfree(buf); usb_free_urb() already releases the transfer
buffer. This mirrors commit 03819abbeb11 ("net: usb: lan78xx: Fix double free
issue with interrupt buffer allocation"). |
| In the Linux kernel, the following vulnerability has been resolved:
can: peak_usb: validate uCAN receive record lengths
pcan_usb_fd_decode_buf() walks uCAN records packed in one USB
receive buffer.
Require each record to contain the fixed header for its type, and verify
CAN payload bytes before copying them into the skb. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vc4: Supply the overflow slot size in BPOS, not the whole bin BO size
vc4_overflow_mem_work() points BPOA at a 512KB slot inside the 16MB
binner BO, but writes the size of the whole BO to BPOS. On every binner
out-of-memory event the PTB is therefore authorized to write tile lists
across all the other slots (which may hold the tile state, tile alloc and
overflow memory of in-flight jobs) and, for any slot but the first, past
the end of the binner BO into unrelated CMA memory.
Since CMA pages are recycled into page cache and user allocations, this
is arbitrary memory corruption by GPU DMA. In practice it shows up as GPU
hangs with corrupted control list pointers, userspace heap corruption, a
GPU that stays permanently wedged after the first hang, and occasional
full system crashes, whenever a job overflows the initial binner slot.
The bug dates back to the conversion from a dedicated overflow BO (where
writing the full BO size was correct) to the slotted binner BO. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vc4: Zero the tile state data array before each BIN job
The binner BO is a single 16MB buffer split into 512KB slots that are
handed out to jobs at submission time and recycled as jobs complete,
without ever being cleared. Each slot holds the job's Tile State Data
Array (TSDA) at its start, followed by the tile allocation pool.
While the tile allocation pool is only walked by the render thread
through branches the binner generated during the current job, the
TSDA is the PTB's own per-tile bookkeeping and is consumed by the
hardware itself. Although the kernel sets the "Auto-initialise Tile
State Data Array" flag in the tile binning mode configuration, the
PTB demonstrably still acts on stale tile state left by the slot's
previous user: the binner ends up creating invalid command streams
with invalid primitive streams and branches, which can cause GPU hangs
as observed in [1][2].
Zero the TSDA when the job's binning slot is configured. This clears
48 bytes per tile (~24KB for a 1080p frame) in the submission path, and
guarantees the PTB never sees another job's tile state.
The tile count is only checked for being non-zero today, so the 8-bit
fields it comes from can describe a tile state array almost six times
larger than the slot it has to live in. Bound it before the slot is
handed out, since such size decides how much of the slot is left for
the tile alloc pool. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: hold event_mutex while checkpointing CRIU events
kfd_criu_checkpoint_events() counts the entries in p->event_idr via
kfd_get_num_events(), allocates an array sized to that count, and then
walks the same IDR to fill it. Neither the count nor the walk holds
p->event_mutex.
The CRIU checkpoint caller holds only p->mutex. Event create and destroy
(kfd_event_create()/kfd_event_destroy()) take p->event_mutex and do not
take p->mutex, so a second thread in the same process can insert or remove
events between the count and the walk. If an event is inserted, the walk
iterates more entries than were counted and writes past the end of the
ev_privs allocation; if an event is removed, the walk dereferences an
entry that is being freed.
Hold p->event_mutex across the count and the walk so both observe a
consistent view of p->event_idr. The lock is released before
copy_to_user(), which only touches the local buffer. The caller already
holds p->mutex and the create/destroy paths never take p->mutex, so the
p->mutex -> p->event_mutex order is not inverted and no deadlock is
introduced.
(cherry picked from commit ff57e223ab105795b05d3ef3f3c35a5a441bcbaa) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: validate DRAW_PRIMITIVES header size before division
vmw_cmd_draw() computes
maxnum = (header->size - sizeof(cmd->body)) / sizeof(*decl);
where header->size is u32 and is taken straight from the user-supplied
command stream. When header->size is less than sizeof(cmd->body) the
unsigned subtraction wraps to nearly 4 GiB, producing a huge maxnum.
Any user-controlled cmd->body.numVertexDecls then passes the bound and
the loop dereferences decl[i] far past the end of the kernel command
bounce buffer, producing an out-of-bounds read of kernel memory.
Reject undersized headers up front. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: bound DMA command body size against suffix pointer
vmw_cmd_dma() locates the DMA suffix at
(unsigned long) &cmd->body + header->size - sizeof(*suffix)
without checking that header->size is large enough to contain both
cmd->body and the suffix. An undersized header makes the suffix
pointer underflow back into the previous command in the bounce
buffer. The verifier later writes suffix->maximumOffset, clobbering
verified fields of an already-relocated earlier command -- a TOCTOU
on the device-visible command stream that lets one command rewrite
another's GMR id, surface id, or other authenticated fields.
Reject the command if the body is too small for the suffix to fit. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: fib6: fix NULL deref in fib6_walk_continue() on multi-batch dump
inet6_dump_fib() saves its progress in cb->args[1] as a positional
index within the current hash chain. Between batches, a concurrent
fib6_new_table() can insert a new table at the chain head, shifting
all existing entries. The saved index then lands on a different
table, causing fib6_dump_table() to set w->root to the wrong table
while w->node still points into the previous one.
fib6_walk_continue() dereferences w->node->parent (NULL) and panics:
BUG: kernel NULL pointer dereference, address: 0000000000000008
RIP: 0010:fib6_walk_continue+0x6e/0x170
Call Trace:
<TASK>
fib6_dump_table.isra.0+0xc5/0x240
inet6_dump_fib+0xf6/0x420
rtnl_dumpit+0x30/0xa0
netlink_dump+0x15b/0x460
netlink_recvmsg+0x1d6/0x2a0
____sys_recvmsg+0x17a/0x190
Fix by storing tb->tb6_id in cb->args[1] instead of a positional
index. On resume, skip entries until the id matches; a concurrent
head-insert can never match the saved id, so the walker always
resumes on the correct table. |
