| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
PM / devfreq: mtk-cci: Fix potential error pointer dereference in probe()
The drv->sram_reg pointer could be set to ERR_PTR(-EPROBE_DEFER) which
would lead to a error pointer dereference. Use IS_ERR_OR_NULL() to check
that the pointer is valid. |
| In the Linux kernel, the following vulnerability has been resolved:
EDAC/i10nm: fix refcount leak in pci_get_dev_wrapper()
As the comment of pci_get_domain_bus_and_slot() says, it returns
a PCI device with refcount incremented, so it doesn't need to
call an extra pci_dev_get() in pci_get_dev_wrapper(), and the PCI
device needs to be put in the error path. |
| In the Linux kernel, the following vulnerability has been resolved:
media: b2c2: Fix use-after-free causing by irq_check_work in flexcop_pci_remove
The original code uses cancel_delayed_work() in flexcop_pci_remove(), which
does not guarantee that the delayed work item irq_check_work has fully
completed if it was already running. This leads to use-after-free scenarios
where flexcop_pci_remove() may free the flexcop_device while irq_check_work
is still active and attempts to dereference the device.
A typical race condition is illustrated below:
CPU 0 (remove) | CPU 1 (delayed work callback)
flexcop_pci_remove() | flexcop_pci_irq_check_work()
cancel_delayed_work() |
flexcop_device_kfree(fc_pci->fc_dev) |
| fc = fc_pci->fc_dev; // UAF
This is confirmed by a KASAN report:
==================================================================
BUG: KASAN: slab-use-after-free in __run_timer_base.part.0+0x7d7/0x8c0
Write of size 8 at addr ffff8880093aa8c8 by task bash/135
...
Call Trace:
<IRQ>
dump_stack_lvl+0x55/0x70
print_report+0xcf/0x610
? __run_timer_base.part.0+0x7d7/0x8c0
kasan_report+0xb8/0xf0
? __run_timer_base.part.0+0x7d7/0x8c0
__run_timer_base.part.0+0x7d7/0x8c0
? __pfx___run_timer_base.part.0+0x10/0x10
? __pfx_read_tsc+0x10/0x10
? ktime_get+0x60/0x140
? lapic_next_event+0x11/0x20
? clockevents_program_event+0x1d4/0x2a0
run_timer_softirq+0xd1/0x190
handle_softirqs+0x16a/0x550
irq_exit_rcu+0xaf/0xe0
sysvec_apic_timer_interrupt+0x70/0x80
</IRQ>
...
Allocated by task 1:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x7f/0x90
__kmalloc_noprof+0x1be/0x460
flexcop_device_kmalloc+0x54/0xe0
flexcop_pci_probe+0x1f/0x9d0
local_pci_probe+0xdc/0x190
pci_device_probe+0x2fe/0x470
really_probe+0x1ca/0x5c0
__driver_probe_device+0x248/0x310
driver_probe_device+0x44/0x120
__driver_attach+0xd2/0x310
bus_for_each_dev+0xed/0x170
bus_add_driver+0x208/0x500
driver_register+0x132/0x460
do_one_initcall+0x89/0x300
kernel_init_freeable+0x40d/0x720
kernel_init+0x1a/0x150
ret_from_fork+0x10c/0x1a0
ret_from_fork_asm+0x1a/0x30
Freed by task 135:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3a/0x60
__kasan_slab_free+0x3f/0x50
kfree+0x137/0x370
flexcop_device_kfree+0x32/0x50
pci_device_remove+0xa6/0x1d0
device_release_driver_internal+0xf8/0x210
pci_stop_bus_device+0x105/0x150
pci_stop_and_remove_bus_device_locked+0x15/0x30
remove_store+0xcc/0xe0
kernfs_fop_write_iter+0x2c3/0x440
vfs_write+0x871/0xd70
ksys_write+0xee/0x1c0
do_syscall_64+0xac/0x280
entry_SYSCALL_64_after_hwframe+0x77/0x7f
...
Replace cancel_delayed_work() with cancel_delayed_work_sync() to ensure
that the delayed work item is properly canceled and any executing delayed
work has finished before the device memory is deallocated.
This bug was initially identified through static analysis. To reproduce
and test it, I simulated the B2C2 FlexCop PCI device in QEMU and introduced
artificial delays within the flexcop_pci_irq_check_work() function to
increase the likelihood of triggering the bug. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: hugetlb: avoid soft lockup when mprotect to large memory area
When calling mprotect() to a large hugetlb memory area in our customer's
workload (~300GB hugetlb memory), soft lockup was observed:
watchdog: BUG: soft lockup - CPU#98 stuck for 23s! [t2_new_sysv:126916]
CPU: 98 PID: 126916 Comm: t2_new_sysv Kdump: loaded Not tainted 6.17-rc7
Hardware name: GIGACOMPUTING R2A3-T40-AAV1/Jefferson CIO, BIOS 5.4.4.1 07/15/2025
pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : mte_clear_page_tags+0x14/0x24
lr : mte_sync_tags+0x1c0/0x240
sp : ffff80003150bb80
x29: ffff80003150bb80 x28: ffff00739e9705a8 x27: 0000ffd2d6a00000
x26: 0000ff8e4bc00000 x25: 00e80046cde00f45 x24: 0000000000022458
x23: 0000000000000000 x22: 0000000000000004 x21: 000000011b380000
x20: ffff000000000000 x19: 000000011b379f40 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000 x9 : ffffc875e0aa5e2c
x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000
x5 : fffffc01ce7a5c00 x4 : 00000000046cde00 x3 : fffffc0000000000
x2 : 0000000000000004 x1 : 0000000000000040 x0 : ffff0046cde7c000
Call trace:
mte_clear_page_tags+0x14/0x24
set_huge_pte_at+0x25c/0x280
hugetlb_change_protection+0x220/0x430
change_protection+0x5c/0x8c
mprotect_fixup+0x10c/0x294
do_mprotect_pkey.constprop.0+0x2e0/0x3d4
__arm64_sys_mprotect+0x24/0x44
invoke_syscall+0x50/0x160
el0_svc_common+0x48/0x144
do_el0_svc+0x30/0xe0
el0_svc+0x30/0xf0
el0t_64_sync_handler+0xc4/0x148
el0t_64_sync+0x1a4/0x1a8
Soft lockup is not triggered with THP or base page because there is
cond_resched() called for each PMD size.
Although the soft lockup was triggered by MTE, it should be not MTE
specific. The other processing which takes long time in the loop may
trigger soft lockup too.
So add cond_resched() for hugetlb to avoid soft lockup. |
| In the Linux kernel, the following vulnerability has been resolved:
RISC-V: Make port I/O string accessors actually work
Fix port I/O string accessors such as `insb', `outsb', etc. which use
the physical PCI port I/O address rather than the corresponding memory
mapping to get at the requested location, which in turn breaks at least
accesses made by our parport driver to a PCIe parallel port such as:
PCI parallel port detected: 1415:c118, I/O at 0x1000(0x1008), IRQ 20
parport0: PC-style at 0x1000 (0x1008), irq 20, using FIFO [PCSPP,TRISTATE,COMPAT,EPP,ECP]
causing a memory access fault:
Unable to handle kernel access to user memory without uaccess routines at virtual address 0000000000001008
Oops [#1]
Modules linked in:
CPU: 1 PID: 350 Comm: cat Not tainted 6.0.0-rc2-00283-g10d4879f9ef0-dirty #23
Hardware name: SiFive HiFive Unmatched A00 (DT)
epc : parport_pc_fifo_write_block_pio+0x266/0x416
ra : parport_pc_fifo_write_block_pio+0xb4/0x416
epc : ffffffff80542c3e ra : ffffffff80542a8c sp : ffffffd88899fc60
gp : ffffffff80fa2700 tp : ffffffd882b1e900 t0 : ffffffd883d0b000
t1 : ffffffffff000002 t2 : 4646393043330a38 s0 : ffffffd88899fcf0
s1 : 0000000000001000 a0 : 0000000000000010 a1 : 0000000000000000
a2 : ffffffd883d0a010 a3 : 0000000000000023 a4 : 00000000ffff8fbb
a5 : ffffffd883d0a001 a6 : 0000000100000000 a7 : ffffffc800000000
s2 : ffffffffff000002 s3 : ffffffff80d28880 s4 : ffffffff80fa1f50
s5 : 0000000000001008 s6 : 0000000000000008 s7 : ffffffd883d0a000
s8 : 0004000000000000 s9 : ffffffff80dc1d80 s10: ffffffd8807e4000
s11: 0000000000000000 t3 : 00000000000000ff t4 : 393044410a303930
t5 : 0000000000001000 t6 : 0000000000040000
status: 0000000200000120 badaddr: 0000000000001008 cause: 000000000000000f
[<ffffffff80543212>] parport_pc_compat_write_block_pio+0xfe/0x200
[<ffffffff8053bbc0>] parport_write+0x46/0xf8
[<ffffffff8050530e>] lp_write+0x158/0x2d2
[<ffffffff80185716>] vfs_write+0x8e/0x2c2
[<ffffffff80185a74>] ksys_write+0x52/0xc2
[<ffffffff80185af2>] sys_write+0xe/0x16
[<ffffffff80003770>] ret_from_syscall+0x0/0x2
---[ end trace 0000000000000000 ]---
For simplicity address the problem by adding PCI_IOBASE to the physical
address requested in the respective wrapper macros only, observing that
the raw accessors such as `__insb', `__outsb', etc. are not supposed to
be used other than by said macros. Remove the cast to `long' that is no
longer needed on `addr' now that it is used as an offset from PCI_IOBASE
and add parentheses around `addr' needed for predictable evaluation in
macro expansion. No need to make said adjustments in separate changes
given that current code is gravely broken and does not ever work. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: fix use-after-free in rtw89_core_tx_kick_off_and_wait()
There is a bug observed when rtw89_core_tx_kick_off_and_wait() tries to
access already freed skb_data:
BUG: KFENCE: use-after-free write in rtw89_core_tx_kick_off_and_wait drivers/net/wireless/realtek/rtw89/core.c:1110
CPU: 6 UID: 0 PID: 41377 Comm: kworker/u64:24 Not tainted 6.17.0-rc1+ #1 PREEMPT(lazy)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS edk2-20250523-14.fc42 05/23/2025
Workqueue: events_unbound cfg80211_wiphy_work [cfg80211]
Use-after-free write at 0x0000000020309d9d (in kfence-#251):
rtw89_core_tx_kick_off_and_wait drivers/net/wireless/realtek/rtw89/core.c:1110
rtw89_core_scan_complete drivers/net/wireless/realtek/rtw89/core.c:5338
rtw89_hw_scan_complete_cb drivers/net/wireless/realtek/rtw89/fw.c:7979
rtw89_chanctx_proceed_cb drivers/net/wireless/realtek/rtw89/chan.c:3165
rtw89_chanctx_proceed drivers/net/wireless/realtek/rtw89/chan.h:141
rtw89_hw_scan_complete drivers/net/wireless/realtek/rtw89/fw.c:8012
rtw89_mac_c2h_scanofld_rsp drivers/net/wireless/realtek/rtw89/mac.c:5059
rtw89_fw_c2h_work drivers/net/wireless/realtek/rtw89/fw.c:6758
process_one_work kernel/workqueue.c:3241
worker_thread kernel/workqueue.c:3400
kthread kernel/kthread.c:463
ret_from_fork arch/x86/kernel/process.c:154
ret_from_fork_asm arch/x86/entry/entry_64.S:258
kfence-#251: 0x0000000056e2393d-0x000000009943cb62, size=232, cache=skbuff_head_cache
allocated by task 41377 on cpu 6 at 77869.159548s (0.009551s ago):
__alloc_skb net/core/skbuff.c:659
__netdev_alloc_skb net/core/skbuff.c:734
ieee80211_nullfunc_get net/mac80211/tx.c:5844
rtw89_core_send_nullfunc drivers/net/wireless/realtek/rtw89/core.c:3431
rtw89_core_scan_complete drivers/net/wireless/realtek/rtw89/core.c:5338
rtw89_hw_scan_complete_cb drivers/net/wireless/realtek/rtw89/fw.c:7979
rtw89_chanctx_proceed_cb drivers/net/wireless/realtek/rtw89/chan.c:3165
rtw89_chanctx_proceed drivers/net/wireless/realtek/rtw89/chan.c:3194
rtw89_hw_scan_complete drivers/net/wireless/realtek/rtw89/fw.c:8012
rtw89_mac_c2h_scanofld_rsp drivers/net/wireless/realtek/rtw89/mac.c:5059
rtw89_fw_c2h_work drivers/net/wireless/realtek/rtw89/fw.c:6758
process_one_work kernel/workqueue.c:3241
worker_thread kernel/workqueue.c:3400
kthread kernel/kthread.c:463
ret_from_fork arch/x86/kernel/process.c:154
ret_from_fork_asm arch/x86/entry/entry_64.S:258
freed by task 1045 on cpu 9 at 77869.168393s (0.001557s ago):
ieee80211_tx_status_skb net/mac80211/status.c:1117
rtw89_pci_release_txwd_skb drivers/net/wireless/realtek/rtw89/pci.c:564
rtw89_pci_release_tx_skbs.isra.0 drivers/net/wireless/realtek/rtw89/pci.c:651
rtw89_pci_release_tx drivers/net/wireless/realtek/rtw89/pci.c:676
rtw89_pci_napi_poll drivers/net/wireless/realtek/rtw89/pci.c:4238
__napi_poll net/core/dev.c:7495
net_rx_action net/core/dev.c:7557 net/core/dev.c:7684
handle_softirqs kernel/softirq.c:580
do_softirq.part.0 kernel/softirq.c:480
__local_bh_enable_ip kernel/softirq.c:407
rtw89_pci_interrupt_threadfn drivers/net/wireless/realtek/rtw89/pci.c:927
irq_thread_fn kernel/irq/manage.c:1133
irq_thread kernel/irq/manage.c:1257
kthread kernel/kthread.c:463
ret_from_fork arch/x86/kernel/process.c:154
ret_from_fork_asm arch/x86/entry/entry_64.S:258
It is a consequence of a race between the waiting and the signaling side
of the completion:
Waiting thread Completing thread
rtw89_core_tx_kick_off_and_wait()
rcu_assign_pointer(skb_data->wait, wait)
/* start waiting */
wait_for_completion_timeout()
rtw89_pci_tx_status()
rtw89_core_tx_wait_complete()
rcu_read_lock()
/* signals completion and
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net: mscc: ocelot: Fix use-after-free caused by cyclic delayed work
The origin code calls cancel_delayed_work() in ocelot_stats_deinit()
to cancel the cyclic delayed work item ocelot->stats_work. However,
cancel_delayed_work() may fail to cancel the work item if it is already
executing. While destroy_workqueue() does wait for all pending work items
in the work queue to complete before destroying the work queue, it cannot
prevent the delayed work item from being rescheduled within the
ocelot_check_stats_work() function. This limitation exists because the
delayed work item is only enqueued into the work queue after its timer
expires. Before the timer expiration, destroy_workqueue() has no visibility
of this pending work item. Once the work queue appears empty,
destroy_workqueue() proceeds with destruction. When the timer eventually
expires, the delayed work item gets queued again, leading to the following
warning:
workqueue: cannot queue ocelot_check_stats_work on wq ocelot-switch-stats
WARNING: CPU: 2 PID: 0 at kernel/workqueue.c:2255 __queue_work+0x875/0xaf0
...
RIP: 0010:__queue_work+0x875/0xaf0
...
RSP: 0018:ffff88806d108b10 EFLAGS: 00010086
RAX: 0000000000000000 RBX: 0000000000000101 RCX: 0000000000000027
RDX: 0000000000000027 RSI: 0000000000000004 RDI: ffff88806d123e88
RBP: ffffffff813c3170 R08: 0000000000000000 R09: ffffed100da247d2
R10: ffffed100da247d1 R11: ffff88806d123e8b R12: ffff88800c00f000
R13: ffff88800d7285c0 R14: ffff88806d0a5580 R15: ffff88800d7285a0
FS: 0000000000000000(0000) GS:ffff8880e5725000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe18e45ea10 CR3: 0000000005e6c000 CR4: 00000000000006f0
Call Trace:
<IRQ>
? kasan_report+0xc6/0xf0
? __pfx_delayed_work_timer_fn+0x10/0x10
? __pfx_delayed_work_timer_fn+0x10/0x10
call_timer_fn+0x25/0x1c0
__run_timer_base.part.0+0x3be/0x8c0
? __pfx_delayed_work_timer_fn+0x10/0x10
? rcu_sched_clock_irq+0xb06/0x27d0
? __pfx___run_timer_base.part.0+0x10/0x10
? try_to_wake_up+0xb15/0x1960
? _raw_spin_lock_irq+0x80/0xe0
? __pfx__raw_spin_lock_irq+0x10/0x10
tmigr_handle_remote_up+0x603/0x7e0
? __pfx_tmigr_handle_remote_up+0x10/0x10
? sched_balance_trigger+0x1c0/0x9f0
? sched_tick+0x221/0x5a0
? _raw_spin_lock_irq+0x80/0xe0
? __pfx__raw_spin_lock_irq+0x10/0x10
? tick_nohz_handler+0x339/0x440
? __pfx_tmigr_handle_remote_up+0x10/0x10
__walk_groups.isra.0+0x42/0x150
tmigr_handle_remote+0x1f4/0x2e0
? __pfx_tmigr_handle_remote+0x10/0x10
? ktime_get+0x60/0x140
? lapic_next_event+0x11/0x20
? clockevents_program_event+0x1d4/0x2a0
? hrtimer_interrupt+0x322/0x780
handle_softirqs+0x16a/0x550
irq_exit_rcu+0xaf/0xe0
sysvec_apic_timer_interrupt+0x70/0x80
</IRQ>
...
The following diagram reveals the cause of the above warning:
CPU 0 (remove) | CPU 1 (delayed work callback)
mscc_ocelot_remove() |
ocelot_deinit() | ocelot_check_stats_work()
ocelot_stats_deinit() |
cancel_delayed_work()| ...
| queue_delayed_work()
destroy_workqueue() | (wait a time)
| __queue_work() //UAF
The above scenario actually constitutes a UAF vulnerability.
The ocelot_stats_deinit() is only invoked when initialization
failure or resource destruction, so we must ensure that any
delayed work items cannot be rescheduled.
Replace cancel_delayed_work() with disable_delayed_work_sync()
to guarantee proper cancellation of the delayed work item and
ensure completion of any currently executing work before the
workqueue is deallocated.
A deadlock concern was considered: ocelot_stats_deinit() is called
in a process context and is not holding any locks that the delayed
work item might also need. Therefore, the use of the _sync() variant
is safe here.
This bug was identified through static analysis. To reproduce the
issue and validate the fix, I simulated ocelot-swit
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: xsk: Fix invalid buffer access for legacy rq
The below crash can be encountered when using xdpsock in rx mode for
legacy rq: the buffer gets released in the XDP_REDIRECT path, and then
once again in the driver. This fix sets the flag to avoid releasing on
the driver side.
XSK handling of buffers for legacy rq was relying on the caller to set
the skip release flag. But the referenced fix started using fragment
counts for pages instead of the skip flag.
Crash log:
general protection fault, probably for non-canonical address 0xffff8881217e3a: 0000 [#1] SMP
CPU: 0 PID: 14 Comm: ksoftirqd/0 Not tainted 6.5.0-rc1+ #31
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:bpf_prog_03b13f331978c78c+0xf/0x28
Code: ...
RSP: 0018:ffff88810082fc98 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff888138404901 RCX: c0ffffc900027cbc
RDX: ffffffffa000b514 RSI: 00ffff8881217e32 RDI: ffff888138404901
RBP: ffff88810082fc98 R08: 0000000000091100 R09: 0000000000000006
R10: 0000000000000800 R11: 0000000000000800 R12: ffffc9000027a000
R13: ffff8881217e2dc0 R14: ffff8881217e2910 R15: ffff8881217e2f00
FS: 0000000000000000(0000) GS:ffff88852c800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000564cb2e2cde0 CR3: 000000010e603004 CR4: 0000000000370eb0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
? die_addr+0x32/0x80
? exc_general_protection+0x192/0x390
? asm_exc_general_protection+0x22/0x30
? 0xffffffffa000b514
? bpf_prog_03b13f331978c78c+0xf/0x28
mlx5e_xdp_handle+0x48/0x670 [mlx5_core]
? dev_gro_receive+0x3b5/0x6e0
mlx5e_xsk_skb_from_cqe_linear+0x6e/0x90 [mlx5_core]
mlx5e_handle_rx_cqe+0x55/0x100 [mlx5_core]
mlx5e_poll_rx_cq+0x87/0x6e0 [mlx5_core]
mlx5e_napi_poll+0x45e/0x6b0 [mlx5_core]
__napi_poll+0x25/0x1a0
net_rx_action+0x28a/0x300
__do_softirq+0xcd/0x279
? sort_range+0x20/0x20
run_ksoftirqd+0x1a/0x20
smpboot_thread_fn+0xa2/0x130
kthread+0xc9/0xf0
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
</TASK>
Modules linked in: mlx5_ib mlx5_core rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm ib_uverbs ib_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter overlay zram zsmalloc fuse [last unloaded: mlx5_core]
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Add NULL pointer checks in dc_stream cursor attribute functions
The function dc_stream_set_cursor_attributes() currently dereferences
the `stream` pointer and nested members `stream->ctx->dc->current_state`
without checking for NULL.
All callers of these functions, such as in
`dcn30_apply_idle_power_optimizations()` and
`amdgpu_dm_plane_handle_cursor_update()`, already perform NULL checks
before calling these functions.
Fixes below:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_stream.c:336 dc_stream_program_cursor_attributes()
error: we previously assumed 'stream' could be null (see line 334)
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_stream.c
327 bool dc_stream_program_cursor_attributes(
328 struct dc_stream_state *stream,
329 const struct dc_cursor_attributes *attributes)
330 {
331 struct dc *dc;
332 bool reset_idle_optimizations = false;
333
334 dc = stream ? stream->ctx->dc : NULL;
^^^^^^
The old code assumed stream could be NULL.
335
--> 336 if (dc_stream_set_cursor_attributes(stream, attributes)) {
^^^^^^
The refactor added an unchecked dereference.
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_stream.c
313 bool dc_stream_set_cursor_attributes(
314 struct dc_stream_state *stream,
315 const struct dc_cursor_attributes *attributes)
316 {
317 bool result = false;
318
319 if (dc_stream_check_cursor_attributes(stream, stream->ctx->dc->current_state, attributes)) {
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ Here.
This function used to check for if stream as NULL and return false at
the start. Probably we should add that back. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: Validate index root when initialize NTFS security
This enhances the sanity check for $SDH and $SII while initializing NTFS
security, guarantees these index root are legit.
[ 162.459513] BUG: KASAN: use-after-free in hdr_find_e.isra.0+0x10c/0x320
[ 162.460176] Read of size 2 at addr ffff8880037bca99 by task mount/243
[ 162.460851]
[ 162.461252] CPU: 0 PID: 243 Comm: mount Not tainted 6.0.0-rc7 #42
[ 162.461744] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[ 162.462609] Call Trace:
[ 162.462954] <TASK>
[ 162.463276] dump_stack_lvl+0x49/0x63
[ 162.463822] print_report.cold+0xf5/0x689
[ 162.464608] ? unwind_get_return_address+0x3a/0x60
[ 162.465766] ? hdr_find_e.isra.0+0x10c/0x320
[ 162.466975] kasan_report+0xa7/0x130
[ 162.467506] ? _raw_spin_lock_irq+0xc0/0xf0
[ 162.467998] ? hdr_find_e.isra.0+0x10c/0x320
[ 162.468536] __asan_load2+0x68/0x90
[ 162.468923] hdr_find_e.isra.0+0x10c/0x320
[ 162.469282] ? cmp_uints+0xe0/0xe0
[ 162.469557] ? cmp_sdh+0x90/0x90
[ 162.469864] ? ni_find_attr+0x214/0x300
[ 162.470217] ? ni_load_mi+0x80/0x80
[ 162.470479] ? entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 162.470931] ? ntfs_bread_run+0x190/0x190
[ 162.471307] ? indx_get_root+0xe4/0x190
[ 162.471556] ? indx_get_root+0x140/0x190
[ 162.471833] ? indx_init+0x1e0/0x1e0
[ 162.472069] ? fnd_clear+0x115/0x140
[ 162.472363] ? _raw_spin_lock_irqsave+0x100/0x100
[ 162.472731] indx_find+0x184/0x470
[ 162.473461] ? sysvec_apic_timer_interrupt+0x57/0xc0
[ 162.474429] ? indx_find_buffer+0x2d0/0x2d0
[ 162.474704] ? do_syscall_64+0x3b/0x90
[ 162.474962] dir_search_u+0x196/0x2f0
[ 162.475381] ? ntfs_nls_to_utf16+0x450/0x450
[ 162.475661] ? ntfs_security_init+0x3d6/0x440
[ 162.475906] ? is_sd_valid+0x180/0x180
[ 162.476191] ntfs_extend_init+0x13f/0x2c0
[ 162.476496] ? ntfs_fix_post_read+0x130/0x130
[ 162.476861] ? iput.part.0+0x286/0x320
[ 162.477325] ntfs_fill_super+0x11e0/0x1b50
[ 162.477709] ? put_ntfs+0x1d0/0x1d0
[ 162.477970] ? vsprintf+0x20/0x20
[ 162.478258] ? set_blocksize+0x95/0x150
[ 162.478538] get_tree_bdev+0x232/0x370
[ 162.478789] ? put_ntfs+0x1d0/0x1d0
[ 162.479038] ntfs_fs_get_tree+0x15/0x20
[ 162.479374] vfs_get_tree+0x4c/0x130
[ 162.479729] path_mount+0x654/0xfe0
[ 162.480124] ? putname+0x80/0xa0
[ 162.480484] ? finish_automount+0x2e0/0x2e0
[ 162.480894] ? putname+0x80/0xa0
[ 162.481467] ? kmem_cache_free+0x1c4/0x440
[ 162.482280] ? putname+0x80/0xa0
[ 162.482714] do_mount+0xd6/0xf0
[ 162.483264] ? path_mount+0xfe0/0xfe0
[ 162.484782] ? __kasan_check_write+0x14/0x20
[ 162.485593] __x64_sys_mount+0xca/0x110
[ 162.486024] do_syscall_64+0x3b/0x90
[ 162.486543] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 162.487141] RIP: 0033:0x7f9d374e948a
[ 162.488324] Code: 48 8b 0d 11 fa 2a 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 008
[ 162.489728] RSP: 002b:00007ffe30e73d18 EFLAGS: 00000206 ORIG_RAX: 00000000000000a5
[ 162.490971] RAX: ffffffffffffffda RBX: 0000561cdb43a060 RCX: 00007f9d374e948a
[ 162.491669] RDX: 0000561cdb43a260 RSI: 0000561cdb43a2e0 RDI: 0000561cdb442af0
[ 162.492050] RBP: 0000000000000000 R08: 0000561cdb43a280 R09: 0000000000000020
[ 162.492459] R10: 00000000c0ed0000 R11: 0000000000000206 R12: 0000561cdb442af0
[ 162.493183] R13: 0000561cdb43a260 R14: 0000000000000000 R15: 00000000ffffffff
[ 162.493644] </TASK>
[ 162.493908]
[ 162.494214] The buggy address belongs to the physical page:
[ 162.494761] page:000000003e38a3d5 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x37bc
[ 162.496064] flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff)
[ 162.497278] raw: 000fffffc0000000 ffffea00000df1c8 ffffea00000df008 0000000000000000
[ 162.498928] raw: 0000000000000000 0000000000240000 0
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: Fix a possible null-pointer dereference in ni_clear()
In a previous commit c1006bd13146, ni->mi.mrec in ni_write_inode()
could be NULL, and thus a NULL check is added for this variable.
However, in the same call stack, ni->mi.mrec can be also dereferenced
in ni_clear():
ntfs_evict_inode(inode)
ni_write_inode(inode, ...)
ni = ntfs_i(inode);
is_rec_inuse(ni->mi.mrec) -> Add a NULL check by previous commit
ni_clear(ntfs_i(inode))
is_rec_inuse(ni->mi.mrec) -> No check
Thus, a possible null-pointer dereference may exist in ni_clear().
To fix it, a NULL check is added in this function. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: Fix memory leak in ath11k_peer_rx_frag_setup
crypto_alloc_shash() allocates resources, which should be released by
crypto_free_shash(). When ath11k_peer_find() fails, there has memory
leak. Add missing crypto_free_shash() to fix this. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Skip fastpath emulation on VM-Exit if next RIP isn't valid
Skip the WRMSR and HLT fastpaths in SVM's VM-Exit handler if the next RIP
isn't valid, e.g. because KVM is running with nrips=false. SVM must
decode and emulate to skip the instruction if the CPU doesn't provide the
next RIP, and getting the instruction bytes to decode requires reading
guest memory. Reading guest memory through the emulator can fault, i.e.
can sleep, which is disallowed since the fastpath handlers run with IRQs
disabled.
BUG: sleeping function called from invalid context at ./include/linux/uaccess.h:106
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 32611, name: qemu
preempt_count: 1, expected: 0
INFO: lockdep is turned off.
irq event stamp: 30580
hardirqs last enabled at (30579): [<ffffffffc08b2527>] vcpu_run+0x1787/0x1db0 [kvm]
hardirqs last disabled at (30580): [<ffffffffb4f62e32>] __schedule+0x1e2/0xed0
softirqs last enabled at (30570): [<ffffffffb4247a64>] fpu_swap_kvm_fpstate+0x44/0x210
softirqs last disabled at (30568): [<ffffffffb4247a64>] fpu_swap_kvm_fpstate+0x44/0x210
CPU: 298 UID: 0 PID: 32611 Comm: qemu Tainted: G U 6.16.0-smp--e6c618b51cfe-sleep #782 NONE
Tainted: [U]=USER
Hardware name: Google Astoria-Turin/astoria, BIOS 0.20241223.2-0 01/17/2025
Call Trace:
<TASK>
dump_stack_lvl+0x7d/0xb0
__might_resched+0x271/0x290
__might_fault+0x28/0x80
kvm_vcpu_read_guest_page+0x8d/0xc0 [kvm]
kvm_fetch_guest_virt+0x92/0xc0 [kvm]
__do_insn_fetch_bytes+0xf3/0x1e0 [kvm]
x86_decode_insn+0xd1/0x1010 [kvm]
x86_emulate_instruction+0x105/0x810 [kvm]
__svm_skip_emulated_instruction+0xc4/0x140 [kvm_amd]
handle_fastpath_invd+0xc4/0x1a0 [kvm]
vcpu_run+0x11a1/0x1db0 [kvm]
kvm_arch_vcpu_ioctl_run+0x5cc/0x730 [kvm]
kvm_vcpu_ioctl+0x578/0x6a0 [kvm]
__se_sys_ioctl+0x6d/0xb0
do_syscall_64+0x8a/0x2c0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f479d57a94b
</TASK>
Note, this is essentially a reapply of commit 5c30e8101e8d ("KVM: SVM:
Skip WRMSR fastpath on VM-Exit if next RIP isn't valid"), but with
different justification (KVM now grabs SRCU when skipping the instruction
for other reasons). |
| In the Linux kernel, the following vulnerability has been resolved:
fs: udf: fix OOB read in lengthAllocDescs handling
When parsing Allocation Extent Descriptor, lengthAllocDescs comes from
on-disk data and must be validated against the block size. Crafted or
corrupted images may set lengthAllocDescs so that the total descriptor
length (sizeof(allocExtDesc) + lengthAllocDescs) exceeds the buffer,
leading udf_update_tag() to call crc_itu_t() on out-of-bounds memory and
trigger a KASAN use-after-free read.
BUG: KASAN: use-after-free in crc_itu_t+0x1d5/0x2b0 lib/crc-itu-t.c:60
Read of size 1 at addr ffff888041e7d000 by task syz-executor317/5309
CPU: 0 UID: 0 PID: 5309 Comm: syz-executor317 Not tainted 6.12.0-rc4-syzkaller-00261-g850925a8133c #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:377 [inline]
print_report+0x169/0x550 mm/kasan/report.c:488
kasan_report+0x143/0x180 mm/kasan/report.c:601
crc_itu_t+0x1d5/0x2b0 lib/crc-itu-t.c:60
udf_update_tag+0x70/0x6a0 fs/udf/misc.c:261
udf_write_aext+0x4d8/0x7b0 fs/udf/inode.c:2179
extent_trunc+0x2f7/0x4a0 fs/udf/truncate.c:46
udf_truncate_tail_extent+0x527/0x7e0 fs/udf/truncate.c:106
udf_release_file+0xc1/0x120 fs/udf/file.c:185
__fput+0x23f/0x880 fs/file_table.c:431
task_work_run+0x24f/0x310 kernel/task_work.c:239
exit_task_work include/linux/task_work.h:43 [inline]
do_exit+0xa2f/0x28e0 kernel/exit.c:939
do_group_exit+0x207/0x2c0 kernel/exit.c:1088
__do_sys_exit_group kernel/exit.c:1099 [inline]
__se_sys_exit_group kernel/exit.c:1097 [inline]
__x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1097
x64_sys_call+0x2634/0x2640 arch/x86/include/generated/asm/syscalls_64.h:232
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
Validate the computed total length against epos->bh->b_size.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Skip scalar adjustment for BPF_NEG if dst is a pointer
In check_alu_op(), the verifier currently calls check_reg_arg() and
adjust_scalar_min_max_vals() unconditionally for BPF_NEG operations.
However, if the destination register holds a pointer, these scalar
adjustments are unnecessary and potentially incorrect.
This patch adds a check to skip the adjustment logic when the destination
register contains a pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
udp_tunnel: use netdev_warn() instead of netdev_WARN()
netdev_WARN() uses WARN/WARN_ON to print a backtrace along with
file and line information. In this case, udp_tunnel_nic_register()
returning an error is just a failed operation, not a kernel bug.
udp_tunnel_nic_register() can fail due to a memory allocation
failure (kzalloc() or udp_tunnel_nic_alloc()).
This is a normal runtime error and not a kernel bug.
Replace netdev_WARN() with netdev_warn() accordingly. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix out-of-bounds read in OnBeacon ESR IE parsing
The Extended Supported Rates (ESR) IE handling in OnBeacon accessed
*(p + 1 + ielen) and *(p + 2 + ielen) without verifying that these
offsets lie within the received frame buffer. A malformed beacon with
an ESR IE positioned at the end of the buffer could cause an
out-of-bounds read, potentially triggering a kernel panic.
Add a boundary check to ensure that the ESR IE body and the subsequent
bytes are within the limits of the frame before attempting to access
them.
This prevents OOB reads caused by malformed beacon frames. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: don't spin in add_stack_record when gfp flags don't allow
syzbot was able to find the following path:
add_stack_record_to_list mm/page_owner.c:182 [inline]
inc_stack_record_count mm/page_owner.c:214 [inline]
__set_page_owner+0x2c3/0x4a0 mm/page_owner.c:333
set_page_owner include/linux/page_owner.h:32 [inline]
post_alloc_hook+0x240/0x2a0 mm/page_alloc.c:1851
prep_new_page mm/page_alloc.c:1859 [inline]
get_page_from_freelist+0x21e4/0x22c0 mm/page_alloc.c:3858
alloc_pages_nolock_noprof+0x94/0x120 mm/page_alloc.c:7554
Don't spin in add_stack_record_to_list() when it is called
from *_nolock() context. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: fastrpc: Fix dma_buf object leak in fastrpc_map_lookup
In fastrpc_map_lookup, dma_buf_get is called to obtain a reference to
the dma_buf for comparison purposes. However, this reference is never
released when the function returns, leading to a dma_buf memory leak.
Fix this by adding dma_buf_put before returning from the function,
ensuring that the temporarily acquired reference is properly released
regardless of whether a matching map is found.
Rule: add |
| In the Linux kernel, the following vulnerability has been resolved:
exfat: fix improper check of dentry.stream.valid_size
We found an infinite loop bug in the exFAT file system that can lead to a
Denial-of-Service (DoS) condition. When a dentry in an exFAT filesystem is
malformed, the following system calls — SYS_openat, SYS_ftruncate, and
SYS_pwrite64 — can cause the kernel to hang.
Root cause analysis shows that the size validation code in exfat_find()
does not check whether dentry.stream.valid_size is negative. As a result,
the system calls mentioned above can succeed and eventually trigger the DoS
issue.
This patch adds a check for negative dentry.stream.valid_size to prevent
this vulnerability. |
