| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: bla: reacquire gw address after skb realloc
The pskb_may_pull() called by batadv_bla_is_backbone_gw() could reallocate
the buffer behind the skb. Variables which were pointing to the old buffer
need to be reassigned to avoid an use-after-free. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: ensure minimal ethernet header on TX
As documented in commit 8bd67ebb50c0 ("net: bridge: xmit: make sure we have
at least eth header len bytes"), it is possible by for a local user with
eBPF TC hook access to attach a tc filter which truncates the packet and
redirects to an batadv interface. But the code assumes that at least
ETH_HLEN bytes are available and thus might read outside of the available
buffer.
The batadv_interface_tx() must therefore always check itself if enough data
is available for the ethernet header and don't rely on min_header_len. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: avoid request storms during pending request
batadv_send_tt_request() allocates a tt_req_node when none exists for the
destination originator node. This should prevent that a multiple TT
requests are send at the same time to an originator.
But if allocation of the send buffer failed, this request must be cleaned
up again. But indicator for such a failure is "ret == false". But the
actual implementation is checking for "ret == true".
The check must be inverted to not loose the information about the TT
request directly after it was attempted to be sent out. This should avoid
potential request storms. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: frag: free unfragmentable packet
The caller of batadv_frag_send_packet() assume that the skb provided to the
function are always consumed. But the pre-check for an empty payload or the
zero fragment size returned an error without any further actions.
A failed pre-check must use the same error handling code as the rest of the
function. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: clean untagged VLAN on netdev registration failure
When an mesh interface is registered, it creates an untagged struct
batadv_meshif_vlan on top of it via the NETDEV_REGISTER notifier. But in
this process, another receiver of this notification can veto the
registration. The netdev registration will be aborted because of this veto.
The register_netdevice() call will try to clean up the net_device using
unregister_netdevice_queue() - which only uses the .priv_destructor to
free private resources. In this situation, .dellink will not be called.
The cleanup of the untagged batadv_meshif_vlan must thefore be done in the
destructor to avoid a leak of this object. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: frag: fix primary_if leak on failed linearization
If the skb has a frag_list, it must be linearized before it can be split
using skb_split(). But when this step failed, it must not only free the skb
but also take care of the reference to the already found primary_if. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: mcast: avoid OOB read of num_dests header
Before the access to struct batadv_tvlv_mcast_tracker's num_dests, it is
attempted to check whether enough space is actually in the network header.
But instead of using offsetofend() to check for the whole size (2) which
must be accessible, offsetof() of is called. The latter is always returning
0. The comparison with the network header length will always return that
enough data is available - even when only 1 or 0 bytes are accessible.
Instead of using offsetofend(), use the more common check for the whole
header. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: prevent TVLV OOB check overflow
A TT unicast TVLV contains the number of VLANs stored in it. This number is
an u16 and gets multiplied by the size of the struct
batadv_tvlv_tt_vlan_data (8 bytes). The size can therefore overflow the u16
used to store the tt_vlan_len. All additional safety checks to prevent
out-of-bounds access of the TVLV buffer are invalid due to this overflow.
Using size_t prevents this overflow and ensures that the safety checks
compare against the actual buffer requirements. |
| In the Linux kernel, the following vulnerability has been resolved:
jbd2: fix integer underflow in jbd2_journal_initialize_fast_commit()
jbd2_journal_initialize_fast_commit() validates journal capacity by
checking (journal->j_last - num_fc_blks < JBD2_MIN_JOURNAL_BLOCKS).
Both j_last and num_fc_blks are unsigned, so when num_fc_blks exceeds
j_last the subtraction wraps to a large value, bypassing the bounds
check.
The resulting underflow corrupts j_last, j_fc_first, and j_free,
leading to journal abort.
Fix by checking num_fc_blks against j_last before the subtraction,
returning -EFSCORRUPTED. |
| In the Linux kernel, the following vulnerability has been resolved:
nvdimm/btt: Free arenas on btt_init() error paths
The arenas allocated by discover_arenas() or create_arenas() are not
freed on some error paths in btt_init(). This leaks memory when BTT
initialization fails.
Call free_arenas() from the affected error paths to release the
allocations.
[ as: commit message and log edits ] |
| In the Linux kernel, the following vulnerability has been resolved:
nvdimm/btt: Free arena sub-allocations on discover_arenas() error path
Memory allocated by btt_freelist_init(), btt_rtt_init(), and
btt_maplocks_init() is not freed on some discover_arenas() error
paths. This leaks memory when arena discovery fails.
Add the missing kfree() calls to release the allocations before
returning an error.
[ as: commit message and log edits ] |
| In the Linux kernel, the following vulnerability has been resolved:
sunrpc: pin svc_xprt across the asynchronous TLS handshake callback
svc_tcp_handshake() stores the raw svc_xprt pointer in
tls_handshake_args.ta_data and submits the request through
tls_server_hello_x509(). The handshake core takes only
sock_hold(req->hr_sk); nothing references the embedding struct
svc_sock that svc_tcp_handshake_done() reaches via container_of().
Two close races leave the in-flight callback writing through a freed
svc_sock. svc_sock_free() calls tls_handshake_cancel() and discards
its return value: a false return means handshake_complete() has
already set HANDSHAKE_F_REQ_COMPLETED but hp_done() may not have
finished, yet svc_sock_free() proceeds to kfree(svsk). The
cancel-loser fall-through inside svc_tcp_handshake() itself produces
the same window: when wait_for_completion_interruptible_timeout()
returns <= 0 (timeout or signal) and tls_handshake_cancel() returns
false, the function does not drain, returns, and svc_handle_xprt()
calls svc_xprt_received(), which clears XPT_BUSY and can drop the
last reference. A concurrent close then runs svc_sock_free() while
svc_tcp_handshake_done() is still updating xpt_flags and walking
svsk->sk_handshake_done.
The corruption surfaces as set_bit/clear_bit RMW into the freed
xpt_flags slab slot and as complete_all() walking and writing the
freed wait_queue_head_t list embedded in sk_handshake_done -- a
slab-corruption primitive, not a benign read. The path is reachable
on any TLS-enabled NFS server whenever a connection close overlaps
the tlshd downcall delivery window; the interruptible wait means
signal delivery suffices, not just SVC_HANDSHAKE_TO expiry.
Take svc_xprt_get(xprt) immediately before tls_server_hello_x509()
so the in-flight callback owns its own reference. Release it on the
two edges where the callback is guaranteed not to fire -- submission
failure from tls_server_hello_x509() and a successful
tls_handshake_cancel() -- and at the tail of
svc_tcp_handshake_done() after complete_all().
[cel: rewrote commit message to describe the actual change] |
| In the Linux kernel, the following vulnerability has been resolved:
sunrpc: wait for in-flight TLS handshake callback when cancel loses race
When wait_for_completion_interruptible_timeout() in
svc_tcp_handshake() returns 0 (timeout) or -ERESTARTSYS (signal) and
tls_handshake_cancel() then returns false, handshake_complete() has
won the cancellation race: it has set HANDSHAKE_F_REQ_COMPLETED and
is about to invoke svc_tcp_handshake_done(), but the callback's
side effects on xpt_flags and on svsk->sk_handshake_done have not
yet committed.
The current code reads xpt_flags immediately to decide whether the
session succeeded. Two races result.
If the callback has executed set_bit(XPT_TLS_SESSION) but not yet
clear_bit(XPT_HANDSHAKE), svc_tcp_handshake() sees a session,
enqueues the transport, and returns. svc_xprt_received() then
clears XPT_BUSY, a worker thread picks the transport up, the
dispatcher in svc_handle_xprt() observes XPT_HANDSHAKE still set,
and xpo_handshake is invoked a second time. That svc_tcp_handshake()
calls init_completion(&svsk->sk_handshake_done) while the original
callback concurrently calls complete_all() on it, corrupting the
embedded swait_queue.
If the callback has set HANDSHAKE_F_REQ_COMPLETED but not yet
entered svc_tcp_handshake_done(), svc_tcp_handshake() reads
XPT_TLS_SESSION as clear and tears the connection down even though
the handshake is about to succeed.
Wait for the callback to commit before inspecting xpt_flags. The
completion is guaranteed to fire because handshake_complete()
invokes svc_tcp_handshake_done() unconditionally once it has set
HANDSHAKE_F_REQ_COMPLETED. |
| In the Linux kernel, the following vulnerability has been resolved:
sunrpc: harden rq_procinfo lifecycle to prevent double-free
The svc_release_rqst() function executes the callback inside
rqstp->rq_procinfo->pc_release. However, if a worker thread begins
processing a new request and encounters an early error path (e.g.,
unsupported protocol, short frame, or bad auth) before a valid
rq_procinfo is installed, a stale release hook can be re-triggered
against reused state from the previous RPC, resulting in a double-free
or use-after-free vulnerability.
Harden the lifecycle of rq_procinfo by:
1. Ensuring svc_release_rqst() always clears rq_procinfo after the
optional pc_release() call, regardless of whether the hook exists.
2. Explicitly clearing rq_procinfo at request entry in svc_process()
before any early decode or drop paths.
3. Ensuring svc_process_bc() does the same at backchannel entry.
This guarantees that error flows will not encounter a non-NULL stale
rq_procinfo pointer when there is nothing to release. |
| In the Linux kernel, the following vulnerability has been resolved:
lockd: Plug nlm_file leak when nlm_do_fopen() fails
A client can repeatedly drive nlm_do_fopen() failures by presenting
file handles that the underlying export rejects. After kzalloc_obj()
succeeds in nlm_lookup_file(), the freshly allocated nlm_file is not
yet inserted into nlm_files[]. The nlm_do_fopen() failure path jumps
to out_unlock, which releases nlm_file_mutex and returns without
freeing the allocation, so each failure leaks one nlm_file.
Route the failure through out_free so kfree() runs before the
function returns. |
| In the Linux kernel, the following vulnerability has been resolved:
lockd: Plug nlm_file refcount leak on cached nlm_do_fopen() failure
The cached-file path in nlm_lookup_file() reaches the found: label
unconditionally, even when nlm_do_fopen() fails. At that label
*result and file->f_count are updated before the error is returned.
The wrappers nlm3svc_lookup_file() and nlm4svc_lookup_file() then
bail out of their switch without copying *result back to their
caller, so the proc handler's local nlm_file pointer remains NULL
and the cleanup path skips nlm_release_file(). The f_count
increment is never released, and nlm_traverse_files() can no
longer reap the file because its refcount never returns to zero
between requests.
Short-circuit the cached path so neither *result nor f_count is
touched when nlm_do_fopen() fails on a hashed nlm_file. |
| In the Linux kernel, the following vulnerability has been resolved:
SUNRPC: Bound-check xdr_buf_to_bvec() stores before writing
xdr_buf_to_bvec() writes a bio_vec into the caller's array before
testing whether that slot is in range, and the head branch performs
the store with no check at all. When the caller's budget is exactly
used up, the next store lands one element past the end of the array.
The overflow label returns count - 1, which masks the surplus store
but cannot undo it.
rq_bvec, the array passed by nfsd_vfs_write(), is allocated to
exactly rq_maxpages entries with no slack. The OOB store can land in
adjacent slab memory; the bv_len and bv_offset fields written there
are derived from client-supplied RPC payload sizes.
Move the in-range check ahead of the store in the head, page-loop,
and tail branches. With the check at the top of each sequence, count
is incremented only after a successful store, so the overflow label
can return count directly. |
| In the Linux kernel, the following vulnerability has been resolved:
remoteproc: qcom: Fix leak when custom dump_segments addition fails
Free allocated minidump_region 'name' in qcom_add_minidump_segments()
when failing before adding the region to 'dump_segments'. Otherwise,
the 'name' is not tracked and is never freed by qcom_minidump_cleanup().
Return error when adding to 'dump_segments' fails. |
| In the Linux kernel, the following vulnerability has been resolved:
MIPS: DEC: Ensure 32-bit stack location for o32 prom_printf()
In 64-bit configurations calling any firmware entry points from a kernel
thread other than the initial one will result in a situation where the
stack has been placed in the XKPHYS 64-bit memory segment.
Consequently the stack pointer is no longer a 32-bit value and when the
32-bit firmware code called uses 32-bit ALU operations to manipulate the
stack pointer, the calculated result is incorrect (in fact in the 64-bit
MIPS ISA almost all 32-bit ALU operations will produce an unpredictable
result when executed on 64-bit data) and control goes astray.
This may happen when no final console driver has been enabled in the
configuration and consequently the initial console continues being used
late into bootstrap, or with an upcoming change that will switch the zs
driver to use a platform device, which in turn will make the console
handover happen only after other kernel threads have already been
started, and the kernel will hang at:
pid_max: default: 32768 minimum: 301
or somewhat later, but always before:
cblist_init_generic: Setting adjustable number of callback queues.
has been printed.
It seems that only the prom_printf() entry point is affected. Of all
the other entry points wired only rex_slot_address() and rex_gettcinfo()
are called from a kernel thread other than the initial one, specifically
kernel_init(), and they are leaf functions that do no business with the
stack, having worked with no issue ever since 64-bit support was added
for the platform back in 2002.
To address this issue then, arrange for the stack to be switched in the
o32 wrapper as required for prom_printf() only, by supplying call_o32()
with a pointer to a chunk of initdata space, which is placed in the
CKSEG0 32-bit compatibility segment, observing that prom_printf() is
only called from console output handler and therefore with the console
lock held, implying no need for this code to be reentrant.
Other firmware entry points may be called with interrupts enabled and no
lock held, and may therefore require that call_o32() be reentrant. They
trigger no issue at this point and "if it ain't broke, don't fix it," so
just leave them alone. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: cpcap-battery: Fix missing nvmem_device_put() causing reference leak
In cpcap_battery_detect_battery_type(), the reference to an nvmem
device obtained via nvmem_device_find() is not released with
nvmem_device_put() on the success or read-failure paths, causing a
permanent reference leak. The driver’s retry logic on subsequent
battery property reads can compound this leak, preventing the nvmem
device from ever being freed.
Found by code review. |
