| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: rawnand: cadence: fix DMA device NULL pointer dereference
The DMA device pointer `dma_dev` was being dereferenced before ensuring
that `cdns_ctrl->dmac` is properly initialized.
Move the assignment of `dma_dev` after successfully acquiring the DMA
channel to ensure the pointer is valid before use. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: ufs-qcom: Fix UFS OCP issue during UFS power down (PC=3)
According to UFS specifications, the power-off sequence for a UFS device
includes:
- Sending an SSU command with Power_Condition=3 and await a response.
- Asserting RST_N low.
- Turning off REF_CLK.
- Turning off VCC.
- Turning off VCCQ/VCCQ2.
As part of ufs shutdown, after the SSU command completion, asserting
hardware reset (HWRST) triggers the device firmware to wake up and
execute its reset routine. This routine initializes hardware blocks and
takes a few milliseconds to complete. During this time, the ICCQ draws a
large current.
This large ICCQ current may cause issues for the regulator which is
supplying power to UFS, because the turn off request from UFS driver to
the regulator framework will be immediately followed by low power
mode(LPM) request by regulator framework. This is done by framework
because UFS which is the only client is requesting for disable. So if
the rail is still in the process of shutting down while ICCQ exceeds LPM
current thresholds, and LPM mode is activated in hardware during this
state, it may trigger an overcurrent protection (OCP) fault in the
regulator.
To prevent this, a 10ms delay is added after asserting HWRST. This
allows the reset operation to complete while power rails remain active
and in high-power mode.
Currently there is no way for Host to query whether the reset is
completed or not and hence this the delay is based on experiments with
Qualcomm UFS controllers across multiple UFS vendors. |
| In the Linux kernel, the following vulnerability has been resolved:
nouveau/firmware: Add missing kfree() of nvkm_falcon_fw::boot
nvkm_falcon_fw::boot is allocated, but no one frees it. This causes a
kmemleak warning.
Make sure this data is deallocated. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix gpu page fault after hibernation on PF passthrough
On PF passthrough environment, after hibernate and then resume, coralgemm
will cause gpu page fault.
Mode1 reset happens during hibernate, but partition mode is not restored
on resume, register mmCP_HYP_XCP_CTL and mmCP_PSP_XCP_CTL is not right
after resume. When CP access the MQD BO, wrong stride size is used,
this will cause out of bound access on the MQD BO, resulting page fault.
The fix is to ensure gfx_v9_4_3_switch_compute_partition() is called
when resume from a hibernation.
KFD resume is called separately during a reset recovery or resume from
suspend sequence. Hence it's not required to be called as part of
partition switch.
(cherry picked from commit 5d1b32cfe4a676fe552416cb5ae847b215463a1a) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/plane: Fix create_in_format_blob() return value
create_in_format_blob() is either supposed to return a valid
pointer or an error, but never NULL. The caller will dereference
the blob when it is not an error, and thus will oops if NULL
returned. Return proper error values in the failure cases. |
| In the Linux kernel, the following vulnerability has been resolved:
ARM: zynq: Fix refcount leak in zynq_early_slcr_init
of_find_compatible_node() returns a node pointer with refcount incremented,
we should use of_node_put() on error path.
Add missing of_node_put() to avoid refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: Fix proto fallback detection with BPF
The sockmap feature allows bpf syscall from userspace, or based
on bpf sockops, replacing the sk_prot of sockets during protocol stack
processing with sockmap's custom read/write interfaces.
'''
tcp_rcv_state_process()
syn_recv_sock()/subflow_syn_recv_sock()
tcp_init_transfer(BPF_SOCK_OPS_PASSIVE_ESTABLISHED_CB)
bpf_skops_established <== sockops
bpf_sock_map_update(sk) <== call bpf helper
tcp_bpf_update_proto() <== update sk_prot
'''
When the server has MPTCP enabled but the client sends a TCP SYN
without MPTCP, subflow_syn_recv_sock() performs a fallback on the
subflow, replacing the subflow sk's sk_prot with the native sk_prot.
'''
subflow_syn_recv_sock()
subflow_ulp_fallback()
subflow_drop_ctx()
mptcp_subflow_ops_undo_override()
'''
Then, this subflow can be normally used by sockmap, which replaces the
native sk_prot with sockmap's custom sk_prot. The issue occurs when the
user executes accept::mptcp_stream_accept::mptcp_fallback_tcp_ops().
Here, it uses sk->sk_prot to compare with the native sk_prot, but this
is incorrect when sockmap is used, as we may incorrectly set
sk->sk_socket->ops.
This fix uses the more generic sk_family for the comparison instead.
Additionally, this also prevents a WARNING from occurring:
result from ./scripts/decode_stacktrace.sh:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 337 at net/mptcp/protocol.c:68 mptcp_stream_accept \
(net/mptcp/protocol.c:4005)
Modules linked in:
...
PKRU: 55555554
Call Trace:
<TASK>
do_accept (net/socket.c:1989)
__sys_accept4 (net/socket.c:2028 net/socket.c:2057)
__x64_sys_accept (net/socket.c:2067)
x64_sys_call (arch/x86/entry/syscall_64.c:41)
do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
RIP: 0033:0x7f87ac92b83d
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix incomplete backport in cfids_invalidation_worker()
The previous commit bdb596ceb4b7 ("smb: client: fix potential UAF in
smb2_close_cached_fid()") was an incomplete backport and missed one
kref_put() call in cfids_invalidation_worker() that should have been
converted to close_cached_dir(). |
| In the Linux kernel, the following vulnerability has been resolved:
page_pool: always add GFP_NOWARN for ATOMIC allocations
Driver authors often forget to add GFP_NOWARN for page allocation
from the datapath. This is annoying to users as OOMs are a fact
of life, and we pretty much expect network Rx to hit page allocation
failures during OOM. Make page pool add GFP_NOWARN for ATOMIC allocations
by default. |
| In the Linux kernel, the following vulnerability has been resolved:
lib/test_kho: check if KHO is enabled
We must check whether KHO is enabled prior to issuing KHO commands,
otherwise KHO internal data structures are not initialized. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: s32cc: fix uninitialized memory in s32_pinctrl_desc
s32_pinctrl_desc is allocated with devm_kmalloc(), but not all of its
fields are initialized. Notably, num_custom_params is used in
pinconf_generic_parse_dt_config(), resulting in intermittent allocation
errors, such as the following splat when probing i2c-imx:
WARNING: CPU: 0 PID: 176 at mm/page_alloc.c:4795 __alloc_pages_noprof+0x290/0x300
[...]
Hardware name: NXP S32G3 Reference Design Board 3 (S32G-VNP-RDB3) (DT)
[...]
Call trace:
__alloc_pages_noprof+0x290/0x300 (P)
___kmalloc_large_node+0x84/0x168
__kmalloc_large_node_noprof+0x34/0x120
__kmalloc_noprof+0x2ac/0x378
pinconf_generic_parse_dt_config+0x68/0x1a0
s32_dt_node_to_map+0x104/0x248
dt_to_map_one_config+0x154/0x1d8
pinctrl_dt_to_map+0x12c/0x280
create_pinctrl+0x6c/0x270
pinctrl_get+0xc0/0x170
devm_pinctrl_get+0x50/0xa0
pinctrl_bind_pins+0x60/0x2a0
really_probe+0x60/0x3a0
[...]
__platform_driver_register+0x2c/0x40
i2c_adap_imx_init+0x28/0xff8 [i2c_imx]
[...]
This results in later parse failures that can cause issues in dependent
drivers:
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c0-pins/i2c0-grp0: could not parse node property
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c0-pins/i2c0-grp0: could not parse node property
[...]
pca953x 0-0022: failed writing register: -6
i2c i2c-0: IMX I2C adapter registered
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c2-pins/i2c2-grp0: could not parse node property
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c2-pins/i2c2-grp0: could not parse node property
i2c i2c-1: IMX I2C adapter registered
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c4-pins/i2c4-grp0: could not parse node property
s32g-siul2-pinctrl 4009c240.pinctrl: /soc@0/pinctrl@4009c240/i2c4-pins/i2c4-grp0: could not parse node property
i2c i2c-2: IMX I2C adapter registered
Fix this by initializing s32_pinctrl_desc with devm_kzalloc() instead of
devm_kmalloc() in s32_pinctrl_probe(), which sets the previously
uninitialized fields to zero. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: fix address removal logic in mptcp_pm_nl_rm_addr
Fix inverted WARN_ON_ONCE condition that prevented normal address
removal counter updates. The current code only executes decrement
logic when the counter is already 0 (abnormal state), while
normal removals (counter > 0) are ignored. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: pegasus-notetaker - fix potential out-of-bounds access
In the pegasus_notetaker driver, the pegasus_probe() function allocates
the URB transfer buffer using the wMaxPacketSize value from
the endpoint descriptor. An attacker can use a malicious USB descriptor
to force the allocation of a very small buffer.
Subsequently, if the device sends an interrupt packet with a specific
pattern (e.g., where the first byte is 0x80 or 0x42),
the pegasus_parse_packet() function parses the packet without checking
the allocated buffer size. This leads to an out-of-bounds memory access. |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: reject negative ifindex
Recent changes in net-next (commit 759ab1edb56c ("net: store netdevs
in an xarray")) refactored the handling of pre-assigned ifindexes
and let syzbot surface a latent problem in ovs. ovs does not validate
ifindex, making it possible to create netdev ports with negative
ifindex values. It's easy to repro with YNL:
$ ./cli.py --spec netlink/specs/ovs_datapath.yaml \
--do new \
--json '{"upcall-pid": 1, "name":"my-dp"}'
$ ./cli.py --spec netlink/specs/ovs_vport.yaml \
--do new \
--json '{"upcall-pid": "00000001", "name": "some-port0", "dp-ifindex":3,"ifindex":4294901760,"type":2}'
$ ip link show
-65536: some-port0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 7a:48:21:ad:0b:fb brd ff:ff:ff:ff:ff:ff
...
Validate the inputs. Now the second command correctly returns:
$ ./cli.py --spec netlink/specs/ovs_vport.yaml \
--do new \
--json '{"upcall-pid": "00000001", "name": "some-port0", "dp-ifindex":3,"ifindex":4294901760,"type":2}'
lib.ynl.NlError: Netlink error: Numerical result out of range
nl_len = 108 (92) nl_flags = 0x300 nl_type = 2
error: -34 extack: {'msg': 'integer out of range', 'unknown': [[type:4 len:36] b'\x0c\x00\x02\x00\x00\x00\x00\x00\x00\x00\x00\x00\x0c\x00\x03\x00\xff\xff\xff\x7f\x00\x00\x00\x00\x08\x00\x01\x00\x08\x00\x00\x00'], 'bad-attr': '.ifindex'}
Accept 0 since it used to be silently ignored. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/guc: Synchronize Dead CT worker with unbind
Cancel and wait for any Dead CT worker to complete before continuing
with device unbinding. Else the worker will end up using resources freed
by the undind operation.
(cherry picked from commit 492671339114e376aaa38626d637a2751cdef263) |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: hda/hdmi: Fix breakage at probing nvhdmi-mcp driver
After restructuring and splitting the HDMI codec driver code, each
HDMI codec driver contains the own build_controls and build_pcms ops.
A copy-n-paste error put the wrong entries for nvhdmi-mcp driver; both
build_controls and build_pcms are swapped. Unfortunately both
callbacks have the very same form, and the compiler didn't complain
it, either. This resulted in a NULL dereference because the PCM
instance hasn't been initialized at calling the build_controls
callback.
Fix it by passing the proper entries. |
| In the Linux kernel, the following vulnerability has been resolved:
sched_ext: Fix unsafe locking in the scx_dump_state()
For built with CONFIG_PREEMPT_RT=y kernels, the dump_lock will be converted
sleepable spinlock and not disable-irq, so the following scenarios occur:
inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
irq_work/0/27 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&rq->__lock){?...}-{2:2}, at: raw_spin_rq_lock_nested+0x2b/0x40
{IN-HARDIRQ-W} state was registered at:
lock_acquire+0x1e1/0x510
_raw_spin_lock_nested+0x42/0x80
raw_spin_rq_lock_nested+0x2b/0x40
sched_tick+0xae/0x7b0
update_process_times+0x14c/0x1b0
tick_periodic+0x62/0x1f0
tick_handle_periodic+0x48/0xf0
timer_interrupt+0x55/0x80
__handle_irq_event_percpu+0x20a/0x5c0
handle_irq_event_percpu+0x18/0xc0
handle_irq_event+0xb5/0x150
handle_level_irq+0x220/0x460
__common_interrupt+0xa2/0x1e0
common_interrupt+0xb0/0xd0
asm_common_interrupt+0x2b/0x40
_raw_spin_unlock_irqrestore+0x45/0x80
__setup_irq+0xc34/0x1a30
request_threaded_irq+0x214/0x2f0
hpet_time_init+0x3e/0x60
x86_late_time_init+0x5b/0xb0
start_kernel+0x308/0x410
x86_64_start_reservations+0x1c/0x30
x86_64_start_kernel+0x96/0xa0
common_startup_64+0x13e/0x148
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&rq->__lock);
<Interrupt>
lock(&rq->__lock);
*** DEADLOCK ***
stack backtrace:
CPU: 0 UID: 0 PID: 27 Comm: irq_work/0
Call Trace:
<TASK>
dump_stack_lvl+0x8c/0xd0
dump_stack+0x14/0x20
print_usage_bug+0x42e/0x690
mark_lock.part.44+0x867/0xa70
? __pfx_mark_lock.part.44+0x10/0x10
? string_nocheck+0x19c/0x310
? number+0x739/0x9f0
? __pfx_string_nocheck+0x10/0x10
? __pfx_check_pointer+0x10/0x10
? kvm_sched_clock_read+0x15/0x30
? sched_clock_noinstr+0xd/0x20
? local_clock_noinstr+0x1c/0xe0
__lock_acquire+0xc4b/0x62b0
? __pfx_format_decode+0x10/0x10
? __pfx_string+0x10/0x10
? __pfx___lock_acquire+0x10/0x10
? __pfx_vsnprintf+0x10/0x10
lock_acquire+0x1e1/0x510
? raw_spin_rq_lock_nested+0x2b/0x40
? __pfx_lock_acquire+0x10/0x10
? dump_line+0x12e/0x270
? raw_spin_rq_lock_nested+0x20/0x40
_raw_spin_lock_nested+0x42/0x80
? raw_spin_rq_lock_nested+0x2b/0x40
raw_spin_rq_lock_nested+0x2b/0x40
scx_dump_state+0x3b3/0x1270
? finish_task_switch+0x27e/0x840
scx_ops_error_irq_workfn+0x67/0x80
irq_work_single+0x113/0x260
irq_work_run_list.part.3+0x44/0x70
run_irq_workd+0x6b/0x90
? __pfx_run_irq_workd+0x10/0x10
smpboot_thread_fn+0x529/0x870
? __pfx_smpboot_thread_fn+0x10/0x10
kthread+0x305/0x3f0
? __pfx_kthread+0x10/0x10
ret_from_fork+0x40/0x70
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
This commit therefore use rq_lock_irqsave/irqrestore() to replace
rq_lock/unlock() in the scx_dump_state(). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Add bpf_prog_run_data_pointers()
syzbot found that cls_bpf_classify() is able to change
tc_skb_cb(skb)->drop_reason triggering a warning in sk_skb_reason_drop().
WARNING: CPU: 0 PID: 5965 at net/core/skbuff.c:1192 __sk_skb_reason_drop net/core/skbuff.c:1189 [inline]
WARNING: CPU: 0 PID: 5965 at net/core/skbuff.c:1192 sk_skb_reason_drop+0x76/0x170 net/core/skbuff.c:1214
struct tc_skb_cb has been added in commit ec624fe740b4 ("net/sched:
Extend qdisc control block with tc control block"), which added a wrong
interaction with db58ba459202 ("bpf: wire in data and data_end for
cls_act_bpf").
drop_reason was added later.
Add bpf_prog_run_data_pointers() helper to save/restore the net_sched
storage colliding with BPF data_meta/data_end. |
| In the Linux kernel, the following vulnerability has been resolved:
codetag: debug: handle existing CODETAG_EMPTY in mark_objexts_empty for slabobj_ext
When alloc_slab_obj_exts() fails and then later succeeds in allocating a
slab extension vector, it calls handle_failed_objexts_alloc() to mark all
objects in the vector as empty. As a result all objects in this slab
(slabA) will have their extensions set to CODETAG_EMPTY.
Later on if this slabA is used to allocate a slabobj_ext vector for
another slab (slabB), we end up with the slabB->obj_exts pointing to a
slabobj_ext vector that itself has a non-NULL slabobj_ext equal to
CODETAG_EMPTY. When slabB gets freed, free_slab_obj_exts() is called to
free slabB->obj_exts vector.
free_slab_obj_exts() calls mark_objexts_empty(slabB->obj_exts) which will
generate a warning because it expects slabobj_ext vectors to have a NULL
obj_ext, not CODETAG_EMPTY.
Modify mark_objexts_empty() to skip the warning and setting the obj_ext
value if it's already set to CODETAG_EMPTY.
To quickly detect this WARN, I modified the code from
WARN_ON(slab_exts[offs].ref.ct) to BUG_ON(slab_exts[offs].ref.ct == 1);
We then obtained this message:
[21630.898561] ------------[ cut here ]------------
[21630.898596] kernel BUG at mm/slub.c:2050!
[21630.898611] Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
[21630.900372] Modules linked in: squashfs isofs vfio_iommu_type1
vhost_vsock vfio vhost_net vmw_vsock_virtio_transport_common vhost tap
vhost_iotlb iommufd vsock binfmt_misc nfsv3 nfs_acl nfs lockd grace
netfs tls rds dns_resolver tun brd overlay ntfs3 exfat btrfs
blake2b_generic xor xor_neon raid6_pq loop sctp ip6_udp_tunnel
udp_tunnel nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib
nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct
nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4
nf_tables rfkill ip_set sunrpc vfat fat joydev sg sch_fq_codel nfnetlink
virtio_gpu sr_mod cdrom drm_client_lib virtio_dma_buf drm_shmem_helper
drm_kms_helper drm ghash_ce backlight virtio_net virtio_blk virtio_scsi
net_failover virtio_console failover virtio_mmio dm_mirror
dm_region_hash dm_log dm_multipath dm_mod fuse i2c_dev virtio_pci
virtio_pci_legacy_dev virtio_pci_modern_dev virtio virtio_ring autofs4
aes_neon_bs aes_ce_blk [last unloaded: hwpoison_inject]
[21630.909177] CPU: 3 UID: 0 PID: 3787 Comm: kylin-process-m Kdump:
loaded Tainted: G W 6.18.0-rc1+ #74 PREEMPT(voluntary)
[21630.910495] Tainted: [W]=WARN
[21630.910867] Hardware name: QEMU KVM Virtual Machine, BIOS unknown
2/2/2022
[21630.911625] pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS
BTYPE=--)
[21630.912392] pc : __free_slab+0x228/0x250
[21630.912868] lr : __free_slab+0x18c/0x250[21630.913334] sp :
ffff8000a02f73e0
[21630.913830] x29: ffff8000a02f73e0 x28: fffffdffc43fc800 x27:
ffff0000c0011c40
[21630.914677] x26: ffff0000c000cac0 x25: ffff00010fe5e5f0 x24:
ffff000102199b40
[21630.915469] x23: 0000000000000003 x22: 0000000000000003 x21:
ffff0000c0011c40
[21630.916259] x20: fffffdffc4086600 x19: fffffdffc43fc800 x18:
0000000000000000
[21630.917048] x17: 0000000000000000 x16: 0000000000000000 x15:
0000000000000000
[21630.917837] x14: 0000000000000000 x13: 0000000000000000 x12:
ffff70001405ee66
[21630.918640] x11: 1ffff0001405ee65 x10: ffff70001405ee65 x9 :
ffff800080a295dc
[21630.919442] x8 : ffff8000a02f7330 x7 : 0000000000000000 x6 :
0000000000003000
[21630.920232] x5 : 0000000024924925 x4 : 0000000000000001 x3 :
0000000000000007
[21630.921021] x2 : 0000000000001b40 x1 : 000000000000001f x0 :
0000000000000001
[21630.921810] Call trace:
[21630.922130] __free_slab+0x228/0x250 (P)
[21630.922669] free_slab+0x38/0x118
[21630.923079] free_to_partial_list+0x1d4/0x340
[21630.923591] __slab_free+0x24c/0x348
[21630.924024] ___cache_free+0xf0/0x110
[21630.924468] qlist_free_all+0x78/0x130
[21630.924922] kasan_quarantine_reduce+0x11
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: pcl818: fix null-ptr-deref in pcl818_ai_cancel()
Syzbot identified an issue [1] in pcl818_ai_cancel(), which stems from
the fact that in case of early device detach via pcl818_detach(),
subdevice dev->read_subdev may not have initialized its pointer to
&struct comedi_async as intended. Thus, any such dereferencing of
&s->async->cmd will lead to general protection fault and kernel crash.
Mitigate this problem by removing a call to pcl818_ai_cancel() from
pcl818_detach() altogether. This way, if the subdevice setups its
support for async commands, everything async-related will be
handled via subdevice's own ->cancel() function in
comedi_device_detach_locked() even before pcl818_detach(). If no
support for asynchronous commands is provided, there is no need
to cancel anything either.
[1] Syzbot crash:
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000005: 0000 [#1] SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f]
CPU: 1 UID: 0 PID: 6050 Comm: syz.0.18 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/18/2025
RIP: 0010:pcl818_ai_cancel+0x69/0x3f0 drivers/comedi/drivers/pcl818.c:762
...
Call Trace:
<TASK>
pcl818_detach+0x66/0xd0 drivers/comedi/drivers/pcl818.c:1115
comedi_device_detach_locked+0x178/0x750 drivers/comedi/drivers.c:207
do_devconfig_ioctl drivers/comedi/comedi_fops.c:848 [inline]
comedi_unlocked_ioctl+0xcde/0x1020 drivers/comedi/comedi_fops.c:2178
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:597 [inline]
... |
