| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to do sanity check on summary info
As Wenqing Liu reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=216456
BUG: KASAN: use-after-free in recover_data+0x63ae/0x6ae0 [f2fs]
Read of size 4 at addr ffff8881464dcd80 by task mount/1013
CPU: 3 PID: 1013 Comm: mount Tainted: G W 6.0.0-rc4 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1 04/01/2014
Call Trace:
dump_stack_lvl+0x45/0x5e
print_report.cold+0xf3/0x68d
kasan_report+0xa8/0x130
recover_data+0x63ae/0x6ae0 [f2fs]
f2fs_recover_fsync_data+0x120d/0x1fc0 [f2fs]
f2fs_fill_super+0x4665/0x61e0 [f2fs]
mount_bdev+0x2cf/0x3b0
legacy_get_tree+0xed/0x1d0
vfs_get_tree+0x81/0x2b0
path_mount+0x47e/0x19d0
do_mount+0xce/0xf0
__x64_sys_mount+0x12c/0x1a0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The root cause is: in fuzzed image, SSA table is corrupted: ofs_in_node
is larger than ADDRS_PER_PAGE(), result in out-of-range access on 4k-size
page.
- recover_data
- do_recover_data
- check_index_in_prev_nodes
- f2fs_data_blkaddr
This patch adds sanity check on summary info in recovery and GC flow
in where the flows rely on them.
After patch:
[ 29.310883] F2FS-fs (loop0): Inconsistent ofs_in_node:65286 in summary, ino:0, nid:6, max:1018 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Fix hard lockup when reading the rx_monitor from debugfs
During I/O and simultaneous cat of /sys/kernel/debug/lpfc/fnX/rx_monitor, a
hard lockup similar to the call trace below may occur.
The spin_lock_bh in lpfc_rx_monitor_report is not protecting from timer
interrupts as expected, so change the strength of the spin lock to _irq.
Kernel panic - not syncing: Hard LOCKUP
CPU: 3 PID: 110402 Comm: cat Kdump: loaded
exception RIP: native_queued_spin_lock_slowpath+91
[IRQ stack]
native_queued_spin_lock_slowpath at ffffffffb814e30b
_raw_spin_lock at ffffffffb89a667a
lpfc_rx_monitor_record at ffffffffc0a73a36 [lpfc]
lpfc_cmf_timer at ffffffffc0abbc67 [lpfc]
__hrtimer_run_queues at ffffffffb8184250
hrtimer_interrupt at ffffffffb8184ab0
smp_apic_timer_interrupt at ffffffffb8a026ba
apic_timer_interrupt at ffffffffb8a01c4f
[End of IRQ stack]
apic_timer_interrupt at ffffffffb8a01c4f
lpfc_rx_monitor_report at ffffffffc0a73c80 [lpfc]
lpfc_rx_monitor_read at ffffffffc0addde1 [lpfc]
full_proxy_read at ffffffffb83e7fc3
vfs_read at ffffffffb833fe71
ksys_read at ffffffffb83402af
do_syscall_64 at ffffffffb800430b
entry_SYSCALL_64_after_hwframe at ffffffffb8a000ad |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: akcipher - default implementation for setting a private key
Changes from v1:
* removed the default implementation from set_pub_key: it is assumed that
an implementation must always have this callback defined as there are
no use case for an algorithm, which doesn't need a public key
Many akcipher implementations (like ECDSA) support only signature
verifications, so they don't have all callbacks defined.
Commit 78a0324f4a53 ("crypto: akcipher - default implementations for
request callbacks") introduced default callbacks for sign/verify
operations, which just return an error code.
However, these are not enough, because before calling sign the caller would
likely call set_priv_key first on the instantiated transform (as the
in-kernel testmgr does). This function does not have a default stub, so the
kernel crashes, when trying to set a private key on an akcipher, which
doesn't support signature generation.
I've noticed this, when trying to add a KAT vector for ECDSA signature to
the testmgr.
With this patch the testmgr returns an error in dmesg (as it should)
instead of crashing the kernel NULL ptr dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: silence the warning when evicting inode with dioread_nolock
When evicting an inode with default dioread_nolock, it could be raced by
the unwritten extents converting kworker after writeback some new
allocated dirty blocks. It convert unwritten extents to written, the
extents could be merged to upper level and free extent blocks, so it
could mark the inode dirty again even this inode has been marked
I_FREEING. But the inode->i_io_list check and warning in
ext4_evict_inode() missing this corner case. Fortunately,
ext4_evict_inode() will wait all extents converting finished before this
check, so it will not lead to inode use-after-free problem, every thing
is OK besides this warning. The WARN_ON_ONCE was originally designed
for finding inode use-after-free issues in advance, but if we add
current dioread_nolock case in, it will become not quite useful, so fix
this warning by just remove this check.
======
WARNING: CPU: 7 PID: 1092 at fs/ext4/inode.c:227
ext4_evict_inode+0x875/0xc60
...
RIP: 0010:ext4_evict_inode+0x875/0xc60
...
Call Trace:
<TASK>
evict+0x11c/0x2b0
iput+0x236/0x3a0
do_unlinkat+0x1b4/0x490
__x64_sys_unlinkat+0x4c/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7fa933c1115b
======
rm kworker
ext4_end_io_end()
vfs_unlink()
ext4_unlink()
ext4_convert_unwritten_io_end_vec()
ext4_convert_unwritten_extents()
ext4_map_blocks()
ext4_ext_map_blocks()
ext4_ext_try_to_merge_up()
__mark_inode_dirty()
check !I_FREEING
locked_inode_to_wb_and_lock_list()
iput()
iput_final()
evict()
ext4_evict_inode()
truncate_inode_pages_final() //wait release io_end
inode_io_list_move_locked()
ext4_release_io_end()
trigger WARN_ON_ONCE() |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: sg: Do not sleep in atomic context
sg_finish_rem_req() calls blk_rq_unmap_user(). The latter function may
sleep. Hence, call sg_finish_rem_req() with interrupts enabled instead
of disabled. |
| In the Linux kernel, the following vulnerability has been resolved:
vhost-vdpa: fix an iotlb memory leak
Before commit 3d5698793897 ("vhost-vdpa: introduce asid based IOTLB")
we called vhost_vdpa_iotlb_unmap(v, iotlb, 0ULL, 0ULL - 1) during
release to free all the resources allocated when processing user IOTLB
messages through vhost_vdpa_process_iotlb_update().
That commit changed the handling of IOTLB a bit, and we accidentally
removed some code called during the release.
We partially fixed this with commit 037d4305569a ("vhost-vdpa: call
vhost_vdpa_cleanup during the release") but a potential memory leak is
still there as showed by kmemleak if the application does not send
VHOST_IOTLB_INVALIDATE or crashes:
unreferenced object 0xffff888007fbaa30 (size 16):
comm "blkio-bench", pid 914, jiffies 4294993521 (age 885.500s)
hex dump (first 16 bytes):
40 73 41 07 80 88 ff ff 00 00 00 00 00 00 00 00 @sA.............
backtrace:
[<0000000087736d2a>] kmem_cache_alloc_trace+0x142/0x1c0
[<0000000060740f50>] vhost_vdpa_process_iotlb_msg+0x68c/0x901 [vhost_vdpa]
[<0000000083e8e205>] vhost_chr_write_iter+0xc0/0x4a0 [vhost]
[<000000008f2f414a>] vhost_vdpa_chr_write_iter+0x18/0x20 [vhost_vdpa]
[<00000000de1cd4a0>] vfs_write+0x216/0x4b0
[<00000000a2850200>] ksys_write+0x71/0xf0
[<00000000de8e720b>] __x64_sys_write+0x19/0x20
[<0000000018b12cbb>] do_syscall_64+0x3f/0x90
[<00000000986ec465>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Let's fix this calling vhost_vdpa_iotlb_unmap() on the whole range in
vhost_vdpa_remove_as(). We move that call before vhost_dev_cleanup()
since we need a valid v->vdev.mm in vhost_vdpa_pa_unmap().
vhost_iotlb_reset() call can be removed, since vhost_vdpa_iotlb_unmap()
on the whole range removes all the entries.
The kmemleak log reported was observed with a vDPA device that has `use_va`
set to true (e.g. VDUSE). This patch has been tested with both types of
devices. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: core: fix resource leak in regulator_register()
I got some resource leak reports while doing fault injection test:
OF: ERROR: memory leak, expected refcount 1 instead of 100,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /i2c/pmic@64/regulators/buck1
unreferenced object 0xffff88810deea000 (size 512):
comm "490-i2c-rt5190a", pid 253, jiffies 4294859840 (age 5061.046s)
hex dump (first 32 bytes):
00 00 00 00 ad 4e ad de ff ff ff ff 00 00 00 00 .....N..........
ff ff ff ff ff ff ff ff a0 1e 00 a1 ff ff ff ff ................
backtrace:
[<00000000d78541e2>] kmalloc_trace+0x21/0x110
[<00000000b343d153>] device_private_init+0x32/0xd0
[<00000000be1f0c70>] device_add+0xb2d/0x1030
[<00000000e3e6344d>] regulator_register+0xaf2/0x12a0
[<00000000e2f5e754>] devm_regulator_register+0x57/0xb0
[<000000008b898197>] rt5190a_probe+0x52a/0x861 [rt5190a_regulator]
unreferenced object 0xffff88810b617b80 (size 32):
comm "490-i2c-rt5190a", pid 253, jiffies 4294859904 (age 5060.983s)
hex dump (first 32 bytes):
72 65 67 75 6c 61 74 6f 72 2e 32 38 36 38 2d 53 regulator.2868-S
55 50 50 4c 59 00 ff ff 29 00 00 00 2b 00 00 00 UPPLY...)...+...
backtrace:
[<000000009da9280d>] __kmalloc_node_track_caller+0x44/0x1b0
[<0000000025c6a4e5>] kstrdup+0x3a/0x70
[<00000000790efb69>] create_regulator+0xc0/0x4e0
[<0000000005ed203a>] regulator_resolve_supply+0x2d4/0x440
[<0000000045796214>] regulator_register+0x10b3/0x12a0
[<00000000e2f5e754>] devm_regulator_register+0x57/0xb0
[<000000008b898197>] rt5190a_probe+0x52a/0x861 [rt5190a_regulator]
After calling regulator_resolve_supply(), the 'rdev->supply' is set
by set_supply(), after this set, in the error path, the resources
need be released, so call regulator_put() to avoid the leaks. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/apic: Don't disable x2APIC if locked
The APIC supports two modes, legacy APIC (or xAPIC), and Extended APIC
(or x2APIC). X2APIC mode is mostly compatible with legacy APIC, but
it disables the memory-mapped APIC interface in favor of one that uses
MSRs. The APIC mode is controlled by the EXT bit in the APIC MSR.
The MMIO/xAPIC interface has some problems, most notably the APIC LEAK
[1]. This bug allows an attacker to use the APIC MMIO interface to
extract data from the SGX enclave.
Introduce support for a new feature that will allow the BIOS to lock
the APIC in x2APIC mode. If the APIC is locked in x2APIC mode and the
kernel tries to disable the APIC or revert to legacy APIC mode a GP
fault will occur.
Introduce support for a new MSR (IA32_XAPIC_DISABLE_STATUS) and handle
the new locked mode when the LEGACY_XAPIC_DISABLED bit is set by
preventing the kernel from trying to disable the x2APIC.
On platforms with the IA32_XAPIC_DISABLE_STATUS MSR, if SGX or TDX are
enabled the LEGACY_XAPIC_DISABLED will be set by the BIOS. If
legacy APIC is required, then it SGX and TDX need to be disabled in the
BIOS.
[1]: https://aepicleak.com/aepicleak.pdf |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid1: stop mdx_raid1 thread when raid1 array run failed
fail run raid1 array when we assemble array with the inactive disk only,
but the mdx_raid1 thread were not stop, Even if the associated resources
have been released. it will caused a NULL dereference when we do poweroff.
This causes the following Oops:
[ 287.587787] BUG: kernel NULL pointer dereference, address: 0000000000000070
[ 287.594762] #PF: supervisor read access in kernel mode
[ 287.599912] #PF: error_code(0x0000) - not-present page
[ 287.605061] PGD 0 P4D 0
[ 287.607612] Oops: 0000 [#1] SMP NOPTI
[ 287.611287] CPU: 3 PID: 5265 Comm: md0_raid1 Tainted: G U 5.10.146 #0
[ 287.619029] Hardware name: xxxxxxx/To be filled by O.E.M, BIOS 5.19 06/16/2022
[ 287.626775] RIP: 0010:md_check_recovery+0x57/0x500 [md_mod]
[ 287.632357] Code: fe 01 00 00 48 83 bb 10 03 00 00 00 74 08 48 89 ......
[ 287.651118] RSP: 0018:ffffc90000433d78 EFLAGS: 00010202
[ 287.656347] RAX: 0000000000000000 RBX: ffff888105986800 RCX: 0000000000000000
[ 287.663491] RDX: ffffc90000433bb0 RSI: 00000000ffffefff RDI: ffff888105986800
[ 287.670634] RBP: ffffc90000433da0 R08: 0000000000000000 R09: c0000000ffffefff
[ 287.677771] R10: 0000000000000001 R11: ffffc90000433ba8 R12: ffff888105986800
[ 287.684907] R13: 0000000000000000 R14: fffffffffffffe00 R15: ffff888100b6b500
[ 287.692052] FS: 0000000000000000(0000) GS:ffff888277f80000(0000) knlGS:0000000000000000
[ 287.700149] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 287.705897] CR2: 0000000000000070 CR3: 000000000320a000 CR4: 0000000000350ee0
[ 287.713033] Call Trace:
[ 287.715498] raid1d+0x6c/0xbbb [raid1]
[ 287.719256] ? __schedule+0x1ff/0x760
[ 287.722930] ? schedule+0x3b/0xb0
[ 287.726260] ? schedule_timeout+0x1ed/0x290
[ 287.730456] ? __switch_to+0x11f/0x400
[ 287.734219] md_thread+0xe9/0x140 [md_mod]
[ 287.738328] ? md_thread+0xe9/0x140 [md_mod]
[ 287.742601] ? wait_woken+0x80/0x80
[ 287.746097] ? md_register_thread+0xe0/0xe0 [md_mod]
[ 287.751064] kthread+0x11a/0x140
[ 287.754300] ? kthread_park+0x90/0x90
[ 287.757974] ret_from_fork+0x1f/0x30
In fact, when raid1 array run fail, we need to do
md_unregister_thread() before raid1_free(). |
| In the Linux kernel, the following vulnerability has been resolved:
vdpa_sim: fix possible memory leak in vdpasim_net_init() and vdpasim_blk_init()
Inject fault while probing module, if device_register() fails in
vdpasim_net_init() or vdpasim_blk_init(), but the refcount of kobject is
not decreased to 0, the name allocated in dev_set_name() is leaked.
Fix this by calling put_device(), so that name can be freed in
callback function kobject_cleanup().
(vdpa_sim_net)
unreferenced object 0xffff88807eebc370 (size 16):
comm "modprobe", pid 3848, jiffies 4362982860 (age 18.153s)
hex dump (first 16 bytes):
76 64 70 61 73 69 6d 5f 6e 65 74 00 6b 6b 6b a5 vdpasim_net.kkk.
backtrace:
[<ffffffff8174f19e>] __kmalloc_node_track_caller+0x4e/0x150
[<ffffffff81731d53>] kstrdup+0x33/0x60
[<ffffffff83a5d421>] kobject_set_name_vargs+0x41/0x110
[<ffffffff82d87aab>] dev_set_name+0xab/0xe0
[<ffffffff82d91a23>] device_add+0xe3/0x1a80
[<ffffffffa0270013>] 0xffffffffa0270013
[<ffffffff81001c27>] do_one_initcall+0x87/0x2e0
[<ffffffff813739cb>] do_init_module+0x1ab/0x640
[<ffffffff81379d20>] load_module+0x5d00/0x77f0
[<ffffffff8137bc40>] __do_sys_finit_module+0x110/0x1b0
[<ffffffff83c4d505>] do_syscall_64+0x35/0x80
[<ffffffff83e0006a>] entry_SYSCALL_64_after_hwframe+0x46/0xb0
(vdpa_sim_blk)
unreferenced object 0xffff8881070c1250 (size 16):
comm "modprobe", pid 6844, jiffies 4364069319 (age 17.572s)
hex dump (first 16 bytes):
76 64 70 61 73 69 6d 5f 62 6c 6b 00 6b 6b 6b a5 vdpasim_blk.kkk.
backtrace:
[<ffffffff8174f19e>] __kmalloc_node_track_caller+0x4e/0x150
[<ffffffff81731d53>] kstrdup+0x33/0x60
[<ffffffff83a5d421>] kobject_set_name_vargs+0x41/0x110
[<ffffffff82d87aab>] dev_set_name+0xab/0xe0
[<ffffffff82d91a23>] device_add+0xe3/0x1a80
[<ffffffffa0220013>] 0xffffffffa0220013
[<ffffffff81001c27>] do_one_initcall+0x87/0x2e0
[<ffffffff813739cb>] do_init_module+0x1ab/0x640
[<ffffffff81379d20>] load_module+0x5d00/0x77f0
[<ffffffff8137bc40>] __do_sys_finit_module+0x110/0x1b0
[<ffffffff83c4d505>] do_syscall_64+0x35/0x80
[<ffffffff83e0006a>] entry_SYSCALL_64_after_hwframe+0x46/0xb0 |
| In the Linux kernel, the following vulnerability has been resolved:
mrp: introduce active flags to prevent UAF when applicant uninit
The caller of del_timer_sync must prevent restarting of the timer, If
we have no this synchronization, there is a small probability that the
cancellation will not be successful.
And syzbot report the fellowing crash:
==================================================================
BUG: KASAN: use-after-free in hlist_add_head include/linux/list.h:929 [inline]
BUG: KASAN: use-after-free in enqueue_timer+0x18/0xa4 kernel/time/timer.c:605
Write at addr f9ff000024df6058 by task syz-fuzzer/2256
Pointer tag: [f9], memory tag: [fe]
CPU: 1 PID: 2256 Comm: syz-fuzzer Not tainted 6.1.0-rc5-syzkaller-00008-
ge01d50cbd6ee #0
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace.part.0+0xe0/0xf0 arch/arm64/kernel/stacktrace.c:156
dump_backtrace arch/arm64/kernel/stacktrace.c:162 [inline]
show_stack+0x18/0x40 arch/arm64/kernel/stacktrace.c:163
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x68/0x84 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:284 [inline]
print_report+0x1a8/0x4a0 mm/kasan/report.c:395
kasan_report+0x94/0xb4 mm/kasan/report.c:495
__do_kernel_fault+0x164/0x1e0 arch/arm64/mm/fault.c:320
do_bad_area arch/arm64/mm/fault.c:473 [inline]
do_tag_check_fault+0x78/0x8c arch/arm64/mm/fault.c:749
do_mem_abort+0x44/0x94 arch/arm64/mm/fault.c:825
el1_abort+0x40/0x60 arch/arm64/kernel/entry-common.c:367
el1h_64_sync_handler+0xd8/0xe4 arch/arm64/kernel/entry-common.c:427
el1h_64_sync+0x64/0x68 arch/arm64/kernel/entry.S:576
hlist_add_head include/linux/list.h:929 [inline]
enqueue_timer+0x18/0xa4 kernel/time/timer.c:605
mod_timer+0x14/0x20 kernel/time/timer.c:1161
mrp_periodic_timer_arm net/802/mrp.c:614 [inline]
mrp_periodic_timer+0xa0/0xc0 net/802/mrp.c:627
call_timer_fn.constprop.0+0x24/0x80 kernel/time/timer.c:1474
expire_timers+0x98/0xc4 kernel/time/timer.c:1519
To fix it, we can introduce a new active flags to make sure the timer will
not restart. |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: vdso: fix NULL deference in vdso_join_timens() when vfork
Testing tools/testing/selftests/timens/vfork_exec.c got below
kernel log:
[ 6.838454] Unable to handle kernel access to user memory without uaccess routines at virtual address 0000000000000020
[ 6.842255] Oops [#1]
[ 6.842871] Modules linked in:
[ 6.844249] CPU: 1 PID: 64 Comm: vfork_exec Not tainted 6.0.0-rc3-rt15+ #8
[ 6.845861] Hardware name: riscv-virtio,qemu (DT)
[ 6.848009] epc : vdso_join_timens+0xd2/0x110
[ 6.850097] ra : vdso_join_timens+0xd2/0x110
[ 6.851164] epc : ffffffff8000635c ra : ffffffff8000635c sp : ff6000000181fbf0
[ 6.852562] gp : ffffffff80cff648 tp : ff60000000fdb700 t0 : 3030303030303030
[ 6.853852] t1 : 0000000000000030 t2 : 3030303030303030 s0 : ff6000000181fc40
[ 6.854984] s1 : ff60000001e6c000 a0 : 0000000000000010 a1 : ffffffff8005654c
[ 6.856221] a2 : 00000000ffffefff a3 : 0000000000000000 a4 : 0000000000000000
[ 6.858114] a5 : 0000000000000000 a6 : 0000000000000008 a7 : 0000000000000038
[ 6.859484] s2 : ff60000001e6c068 s3 : ff6000000108abb0 s4 : 0000000000000000
[ 6.860751] s5 : 0000000000001000 s6 : ffffffff8089dc40 s7 : ffffffff8089dc38
[ 6.862029] s8 : ffffffff8089dc30 s9 : ff60000000fdbe38 s10: 000000000000005e
[ 6.863304] s11: ffffffff80cc3510 t3 : ffffffff80d1112f t4 : ffffffff80d1112f
[ 6.864565] t5 : ffffffff80d11130 t6 : ff6000000181fa00
[ 6.865561] status: 0000000000000120 badaddr: 0000000000000020 cause: 000000000000000d
[ 6.868046] [<ffffffff8008dc94>] timens_commit+0x38/0x11a
[ 6.869089] [<ffffffff8008dde8>] timens_on_fork+0x72/0xb4
[ 6.870055] [<ffffffff80190096>] begin_new_exec+0x3c6/0x9f0
[ 6.871231] [<ffffffff801d826c>] load_elf_binary+0x628/0x1214
[ 6.872304] [<ffffffff8018ee7a>] bprm_execve+0x1f2/0x4e4
[ 6.873243] [<ffffffff8018f90c>] do_execveat_common+0x16e/0x1ee
[ 6.874258] [<ffffffff8018f9c8>] sys_execve+0x3c/0x48
[ 6.875162] [<ffffffff80003556>] ret_from_syscall+0x0/0x2
[ 6.877484] ---[ end trace 0000000000000000 ]---
This is because the mm->context.vdso_info is NULL in vfork case. From
another side, mm->context.vdso_info either points to vdso info
for RV64 or vdso info for compat, there's no need to bloat riscv's
mm_context_t, we can handle the difference when setup the additional
page for vdso. |
| In the Linux kernel, the following vulnerability has been resolved:
io-wq: Fix memory leak in worker creation
If the CPU mask allocation for a node fails, then the memory allocated for
the 'io_wqe' struct of the current node doesn't get freed on the error
handling path, since it has not yet been added to the 'wqes' array.
This was spotted when fuzzing v6.1-rc1 with Syzkaller:
BUG: memory leak
unreferenced object 0xffff8880093d5000 (size 1024):
comm "syz-executor.2", pid 7701, jiffies 4295048595 (age 13.900s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000cb463369>] __kmem_cache_alloc_node+0x18e/0x720
[<00000000147a3f9c>] kmalloc_node_trace+0x2a/0x130
[<000000004e107011>] io_wq_create+0x7b9/0xdc0
[<00000000c38b2018>] io_uring_alloc_task_context+0x31e/0x59d
[<00000000867399da>] __io_uring_add_tctx_node.cold+0x19/0x1ba
[<000000007e0e7a79>] io_uring_setup.cold+0x1b80/0x1dce
[<00000000b545e9f6>] __x64_sys_io_uring_setup+0x5d/0x80
[<000000008a8a7508>] do_syscall_64+0x5d/0x90
[<000000004ac08bec>] entry_SYSCALL_64_after_hwframe+0x63/0xcd |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: Fix pci_device_is_present() for VFs by checking PF
pci_device_is_present() previously didn't work for VFs because it reads the
Vendor and Device ID, which are 0xffff for VFs, which looks like they
aren't present. Check the PF instead.
Wei Gong reported that if virtio I/O is in progress when the driver is
unbound or "0" is written to /sys/.../sriov_numvfs, the virtio I/O
operation hangs, which may result in output like this:
task:bash state:D stack: 0 pid: 1773 ppid: 1241 flags:0x00004002
Call Trace:
schedule+0x4f/0xc0
blk_mq_freeze_queue_wait+0x69/0xa0
blk_mq_freeze_queue+0x1b/0x20
blk_cleanup_queue+0x3d/0xd0
virtblk_remove+0x3c/0xb0 [virtio_blk]
virtio_dev_remove+0x4b/0x80
...
device_unregister+0x1b/0x60
unregister_virtio_device+0x18/0x30
virtio_pci_remove+0x41/0x80
pci_device_remove+0x3e/0xb0
This happened because pci_device_is_present(VF) returned "false" in
virtio_pci_remove(), so it called virtio_break_device(). The broken vq
meant that vring_interrupt() skipped the vq.callback() that would have
completed the virtio I/O operation via virtblk_done().
[bhelgaas: commit log, simplify to always use pci_physfn(), add stable tag] |
| In the Linux kernel, the following vulnerability has been resolved:
media: dvb-usb: fix memory leak in dvb_usb_adapter_init()
Syzbot reports a memory leak in "dvb_usb_adapter_init()".
The leak is due to not accounting for and freeing current iteration's
adapter->priv in case of an error. Currently if an error occurs,
it will exit before incrementing "num_adapters_initalized",
which is used as a reference counter to free all adap->priv
in "dvb_usb_adapter_exit()". There are multiple error paths that
can exit from before incrementing the counter. Including the
error handling paths for "dvb_usb_adapter_stream_init()",
"dvb_usb_adapter_dvb_init()" and "dvb_usb_adapter_frontend_init()"
within "dvb_usb_adapter_init()".
This means that in case of an error in any of these functions the
current iteration is not accounted for and the current iteration's
adap->priv is not freed.
Fix this by freeing the current iteration's adap->priv in the
"stream_init_err:" label in the error path. The rest of the
(accounted for) adap->priv objects are freed in dvb_usb_adapter_exit()
as expected using the num_adapters_initalized variable.
Syzbot report:
BUG: memory leak
unreferenced object 0xffff8881172f1a00 (size 512):
comm "kworker/0:2", pid 139, jiffies 4294994873 (age 10.960s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff844af012>] dvb_usb_adapter_init drivers/media/usb/dvb-usb/dvb-usb-init.c:75 [inline]
[<ffffffff844af012>] dvb_usb_init drivers/media/usb/dvb-usb/dvb-usb-init.c:184 [inline]
[<ffffffff844af012>] dvb_usb_device_init.cold+0x4e5/0x79e drivers/media/usb/dvb-usb/dvb-usb-init.c:308
[<ffffffff830db21d>] dib0700_probe+0x8d/0x1b0 drivers/media/usb/dvb-usb/dib0700_core.c:883
[<ffffffff82d3fdc7>] usb_probe_interface+0x177/0x370 drivers/usb/core/driver.c:396
[<ffffffff8274ab37>] call_driver_probe drivers/base/dd.c:542 [inline]
[<ffffffff8274ab37>] really_probe.part.0+0xe7/0x310 drivers/base/dd.c:621
[<ffffffff8274ae6c>] really_probe drivers/base/dd.c:583 [inline]
[<ffffffff8274ae6c>] __driver_probe_device+0x10c/0x1e0 drivers/base/dd.c:752
[<ffffffff8274af6a>] driver_probe_device+0x2a/0x120 drivers/base/dd.c:782
[<ffffffff8274b786>] __device_attach_driver+0xf6/0x140 drivers/base/dd.c:899
[<ffffffff82747c87>] bus_for_each_drv+0xb7/0x100 drivers/base/bus.c:427
[<ffffffff8274b352>] __device_attach+0x122/0x260 drivers/base/dd.c:970
[<ffffffff827498f6>] bus_probe_device+0xc6/0xe0 drivers/base/bus.c:487
[<ffffffff82745cdb>] device_add+0x5fb/0xdf0 drivers/base/core.c:3405
[<ffffffff82d3d202>] usb_set_configuration+0x8f2/0xb80 drivers/usb/core/message.c:2170
[<ffffffff82d4dbfc>] usb_generic_driver_probe+0x8c/0xc0 drivers/usb/core/generic.c:238
[<ffffffff82d3f49c>] usb_probe_device+0x5c/0x140 drivers/usb/core/driver.c:293
[<ffffffff8274ab37>] call_driver_probe drivers/base/dd.c:542 [inline]
[<ffffffff8274ab37>] really_probe.part.0+0xe7/0x310 drivers/base/dd.c:621
[<ffffffff8274ae6c>] really_probe drivers/base/dd.c:583 [inline]
[<ffffffff8274ae6c>] __driver_probe_device+0x10c/0x1e0 drivers/base/dd.c:752 |
| In the Linux kernel, the following vulnerability has been resolved:
Input: cros_ec_keyb - fix an invalid memory access
If cros_ec_keyb_register_matrix() isn't called (due to
`buttons_switches_only`) in cros_ec_keyb_probe(), `ckdev->idev` remains
NULL. An invalid memory access is observed in cros_ec_keyb_process()
when receiving an EC_MKBP_EVENT_KEY_MATRIX event in cros_ec_keyb_work()
in such case.
Unable to handle kernel read from unreadable memory at virtual address 0000000000000028
...
x3 : 0000000000000000 x2 : 0000000000000000
x1 : 0000000000000000 x0 : 0000000000000000
Call trace:
input_event
cros_ec_keyb_work
blocking_notifier_call_chain
ec_irq_thread
It's still unknown about why the kernel receives such malformed event,
in any cases, the kernel shouldn't access `ckdev->idev` and friends if
the driver doesn't intend to initialize them. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Check the untrusted offset in FF-A memory share
Verify the offset to prevent OOB access in the hypervisor
FF-A buffer in case an untrusted large enough value
[U32_MAX - sizeof(struct ffa_composite_mem_region) + 1, U32_MAX]
is set from the host kernel. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/rw: ensure allocated iovec gets cleared for early failure
A previous commit reused the recyling infrastructure for early cleanup,
but this is not enough for the case where our internal caches have
overflowed. If this happens, then the allocated iovec can get leaked if
the request is also aborted early.
Reinstate the previous forced free of the iovec for that situation. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: Validate command header size against SVGA_CMD_MAX_DATASIZE
This data originates from userspace and is used in buffer offset
calculations which could potentially overflow causing an out-of-bounds
access. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btusb: reorder cleanup in btusb_disconnect to avoid UAF
There is a KASAN: slab-use-after-free read in btusb_disconnect().
Calling "usb_driver_release_interface(&btusb_driver, data->intf)" will
free the btusb data associated with the interface. The same data is
then used later in the function, hence the UAF.
Fix by moving the accesses to btusb data to before the data is free'd. |
