| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
tty: n_gsm: Don't block input queue by waiting MSC
Currently gsm_queue() processes incoming frames and when opening
a DLC channel it calls gsm_dlci_open() which calls gsm_modem_update().
If basic mode is used it calls gsm_modem_upd_via_msc() and it
cannot block the input queue by waiting the response to come
into the same input queue.
Instead allow sending Modem Status Command without waiting for remote
end to respond. Define a new function gsm_modem_send_initial_msc()
for this purpose. As MSC is only valid for basic encoding, it does
not do anything for advanced or when convergence layer type 2 is used. |
| In the Linux kernel, the following vulnerability has been resolved:
net/9p: Fix buffer overflow in USB transport layer
A buffer overflow vulnerability exists in the USB 9pfs transport layer
where inconsistent size validation between packet header parsing and
actual data copying allows a malicious USB host to overflow heap buffers.
The issue occurs because:
- usb9pfs_rx_header() validates only the declared size in packet header
- usb9pfs_rx_complete() uses req->actual (actual received bytes) for
memcpy
This allows an attacker to craft packets with small declared size
(bypassing validation) but large actual payload (triggering overflow
in memcpy).
Add validation in usb9pfs_rx_complete() to ensure req->actual does not
exceed the buffer capacity before copying data. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: fix divide-by-zero in comedi_buf_munge()
The comedi_buf_munge() function performs a modulo operation
`async->munge_chan %= async->cmd.chanlist_len` without first
checking if chanlist_len is zero. If a user program submits a command with
chanlist_len set to zero, this causes a divide-by-zero error when the device
processes data in the interrupt handler path.
Add a check for zero chanlist_len at the beginning of the
function, similar to the existing checks for !map and
CMDF_RAWDATA flag. When chanlist_len is zero, update
munge_count and return early, indicating the data was
handled without munging.
This prevents potential kernel panics from malformed user commands. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: lan78xx: Fix lost EEPROM read timeout error(-ETIMEDOUT) in lan78xx_read_raw_eeprom
Syzbot reported read of uninitialized variable BUG with following call stack.
lan78xx 8-1:1.0 (unnamed net_device) (uninitialized): EEPROM read operation timeout
=====================================================
BUG: KMSAN: uninit-value in lan78xx_read_eeprom drivers/net/usb/lan78xx.c:1095 [inline]
BUG: KMSAN: uninit-value in lan78xx_init_mac_address drivers/net/usb/lan78xx.c:1937 [inline]
BUG: KMSAN: uninit-value in lan78xx_reset+0x999/0x2cd0 drivers/net/usb/lan78xx.c:3241
lan78xx_read_eeprom drivers/net/usb/lan78xx.c:1095 [inline]
lan78xx_init_mac_address drivers/net/usb/lan78xx.c:1937 [inline]
lan78xx_reset+0x999/0x2cd0 drivers/net/usb/lan78xx.c:3241
lan78xx_bind+0x711/0x1690 drivers/net/usb/lan78xx.c:3766
lan78xx_probe+0x225c/0x3310 drivers/net/usb/lan78xx.c:4707
Local variable sig.i.i created at:
lan78xx_read_eeprom drivers/net/usb/lan78xx.c:1092 [inline]
lan78xx_init_mac_address drivers/net/usb/lan78xx.c:1937 [inline]
lan78xx_reset+0x77e/0x2cd0 drivers/net/usb/lan78xx.c:3241
lan78xx_bind+0x711/0x1690 drivers/net/usb/lan78xx.c:3766
The function lan78xx_read_raw_eeprom failed to properly propagate EEPROM
read timeout errors (-ETIMEDOUT). In the fallthrough path, it first
attempted to restore the pin configuration for LED outputs and then
returned only the status of that restore operation, discarding the
original timeout error.
As a result, callers could mistakenly treat the data buffer as valid
even though the EEPROM read had actually timed out with no data or partial
data.
To fix this, handle errors in restoring the LED pin configuration separately.
If the restore succeeds, return any prior EEPROM timeout error correctly
to the caller. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: qcom: audioreach: fix potential null pointer dereference
It is possible that the topology parsing function
audioreach_widget_load_module_common() could return NULL or an error
pointer. Add missing NULL check so that we do not dereference it. |
| In the Linux kernel through 6.9, an untrusted hypervisor can inject virtual interrupts 0 and 14 at any point in time and can trigger the SIGFPE signal handler in userspace applications. This affects AMD SEV-SNP and AMD SEV-ES. |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: client: fix memory leak in smb3_fs_context_parse_param
The user calls fsconfig twice, but when the program exits, free() only
frees ctx->source for the second fsconfig, not the first.
Regarding fc->source, there is no code in the fs context related to its
memory reclamation.
To fix this memory leak, release the source memory corresponding to ctx
or fc before each parsing.
syzbot reported:
BUG: memory leak
unreferenced object 0xffff888128afa360 (size 96):
backtrace (crc 79c9c7ba):
kstrdup+0x3c/0x80 mm/util.c:84
smb3_fs_context_parse_param+0x229b/0x36c0 fs/smb/client/fs_context.c:1444
BUG: memory leak
unreferenced object 0xffff888112c7d900 (size 96):
backtrace (crc 79c9c7ba):
smb3_fs_context_fullpath+0x70/0x1b0 fs/smb/client/fs_context.c:629
smb3_fs_context_parse_param+0x2266/0x36c0 fs/smb/client/fs_context.c:1438 |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Fix NULL pointer dereference in snd_usb_mixer_controls_badd
In snd_usb_create_streams(), for UAC version 3 devices, the Interface
Association Descriptor (IAD) is retrieved via usb_ifnum_to_if(). If this
call fails, a fallback routine attempts to obtain the IAD from the next
interface and sets a BADD profile. However, snd_usb_mixer_controls_badd()
assumes that the IAD retrieved from usb_ifnum_to_if() is always valid,
without performing a NULL check. This can lead to a NULL pointer
dereference when usb_ifnum_to_if() fails to find the interface descriptor.
This patch adds a NULL pointer check after calling usb_ifnum_to_if() in
snd_usb_mixer_controls_badd() to prevent the dereference.
This issue was discovered by syzkaller, which triggered the bug by sending
a crafted USB device descriptor. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/netiucv: Fix return type of netiucv_tx()
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/netiucv.c:1854:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = netiucv_tx,
^~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of netiucv_tx() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future.
Additionally, while in the area, remove a comment block that is no
longer relevant. |
| In the Linux kernel, the following vulnerability has been resolved:
virtio-net: fix received length check in big packets
Since commit 4959aebba8c0 ("virtio-net: use mtu size as buffer length
for big packets"), when guest gso is off, the allocated size for big
packets is not MAX_SKB_FRAGS * PAGE_SIZE anymore but depends on
negotiated MTU. The number of allocated frags for big packets is stored
in vi->big_packets_num_skbfrags.
Because the host announced buffer length can be malicious (e.g. the host
vhost_net driver's get_rx_bufs is modified to announce incorrect
length), we need a check in virtio_net receive path. Currently, the
check is not adapted to the new change which can lead to NULL page
pointer dereference in the below while loop when receiving length that
is larger than the allocated one.
This commit fixes the received length check corresponding to the new
change. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bridge: fix use-after-free due to MST port state bypass
syzbot reported[1] a use-after-free when deleting an expired fdb. It is
due to a race condition between learning still happening and a port being
deleted, after all its fdbs have been flushed. The port's state has been
toggled to disabled so no learning should happen at that time, but if we
have MST enabled, it will bypass the port's state, that together with VLAN
filtering disabled can lead to fdb learning at a time when it shouldn't
happen while the port is being deleted. VLAN filtering must be disabled
because we flush the port VLANs when it's being deleted which will stop
learning. This fix adds a check for the port's vlan group which is
initialized to NULL when the port is getting deleted, that avoids the port
state bypass. When MST is enabled there would be a minimal new overhead
in the fast-path because the port's vlan group pointer is cache-hot.
[1] https://syzkaller.appspot.com/bug?extid=dd280197f0f7ab3917be |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel: Fix KASAN global-out-of-bounds warning
When running "perf mem record" command on CWF, the below KASAN
global-out-of-bounds warning is seen.
==================================================================
BUG: KASAN: global-out-of-bounds in cmt_latency_data+0x176/0x1b0
Read of size 4 at addr ffffffffb721d000 by task dtlb/9850
Call Trace:
kasan_report+0xb8/0xf0
cmt_latency_data+0x176/0x1b0
setup_arch_pebs_sample_data+0xf49/0x2560
intel_pmu_drain_arch_pebs+0x577/0xb00
handle_pmi_common+0x6c4/0xc80
The issue is caused by below code in __grt_latency_data(). The code
tries to access x86_hybrid_pmu structure which doesn't exist on
non-hybrid platform like CWF.
WARN_ON_ONCE(hybrid_pmu(event->pmu)->pmu_type == hybrid_big)
So add is_hybrid() check before calling this WARN_ON_ONCE to fix the
global-out-of-bounds access issue. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-throttle: prevent overflow while calculating wait time
There is a problem found by code review in tg_with_in_bps_limit() that
'bps_limit * jiffy_elapsed_rnd' might overflow. Fix the problem by
calling mul_u64_u64_div_u64() instead. |
| In the Linux kernel, the following vulnerability has been resolved:
hfs: fix OOB Read in __hfs_brec_find
Syzbot reported a OOB read bug:
==================================================================
BUG: KASAN: slab-out-of-bounds in hfs_strcmp+0x117/0x190
fs/hfs/string.c:84
Read of size 1 at addr ffff88807eb62c4e by task kworker/u4:1/11
CPU: 1 PID: 11 Comm: kworker/u4:1 Not tainted
6.1.0-rc6-syzkaller-00308-g644e9524388a #0
Workqueue: writeback wb_workfn (flush-7:0)
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x1b1/0x28e lib/dump_stack.c:106
print_address_description+0x74/0x340 mm/kasan/report.c:284
print_report+0x107/0x1f0 mm/kasan/report.c:395
kasan_report+0xcd/0x100 mm/kasan/report.c:495
hfs_strcmp+0x117/0x190 fs/hfs/string.c:84
__hfs_brec_find+0x213/0x5c0 fs/hfs/bfind.c:75
hfs_brec_find+0x276/0x520 fs/hfs/bfind.c:138
hfs_write_inode+0x34c/0xb40 fs/hfs/inode.c:462
write_inode fs/fs-writeback.c:1440 [inline]
If the input inode of hfs_write_inode() is incorrect:
struct inode
struct hfs_inode_info
struct hfs_cat_key
struct hfs_name
u8 len # len is greater than HFS_NAMELEN(31) which is the
maximum length of an HFS filename
OOB read occurred:
hfs_write_inode()
hfs_brec_find()
__hfs_brec_find()
hfs_cat_keycmp()
hfs_strcmp() # OOB read occurred due to len is too large
Fix this by adding a Check on len in hfs_write_inode() before calling
hfs_brec_find(). |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel/uncore: Fix reference count leak in snr_uncore_mmio_map()
pci_get_device() will increase the reference count for the returned
pci_dev, so snr_uncore_get_mc_dev() will return a pci_dev with its
reference count increased. We need to call pci_dev_put() to decrease the
reference count. Let's add the missing pci_dev_put(). |
| In the Linux kernel, the following vulnerability has been resolved:
fpga: prevent integer overflow in dfl_feature_ioctl_set_irq()
The "hdr.count * sizeof(s32)" multiplication can overflow on 32 bit
systems leading to memory corruption. Use array_size() to fix that. |
| In the Linux kernel, the following vulnerability has been resolved:
net: netsec: fix error handling in netsec_register_mdio()
If phy_device_register() fails, phy_device_free() need be called to
put refcount, so memory of phy device and device name can be freed
in callback function.
If get_phy_device() fails, mdiobus_unregister() need be called,
or it will cause warning in mdiobus_free() and kobject is leaked. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: amba-pl011: avoid SBSA UART accessing DMACR register
Chapter "B Generic UART" in "ARM Server Base System Architecture" [1]
documentation describes a generic UART interface. Such generic UART
does not support DMA. In current code, sbsa_uart_pops and
amba_pl011_pops share the same stop_rx operation, which will invoke
pl011_dma_rx_stop, leading to an access of the DMACR register. This
commit adds a using_rx_dma check in pl011_dma_rx_stop to avoid the
access to DMACR register for SBSA UARTs which does not support DMA.
When the kernel enables DMA engine with "CONFIG_DMA_ENGINE=y", Linux
SBSA PL011 driver will access PL011 DMACR register in some functions.
For most real SBSA Pl011 hardware implementations, the DMACR write
behaviour will be ignored. So these DMACR operations will not cause
obvious problems. But for some virtual SBSA PL011 hardware, like Xen
virtual SBSA PL011 (vpl011) device, the behaviour might be different.
Xen vpl011 emulation will inject a data abort to guest, when guest is
accessing an unimplemented UART register. As Xen VPL011 is SBSA
compatible, it will not implement DMACR register. So when Linux SBSA
PL011 driver access DMACR register, it will get an unhandled data abort
fault and the application will get a segmentation fault:
Unhandled fault at 0xffffffc00944d048
Mem abort info:
ESR = 0x96000000
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x00: ttbr address size fault
Data abort info:
ISV = 0, ISS = 0x00000000
CM = 0, WnR = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000020e2e000
[ffffffc00944d048] pgd=100000003ffff803, p4d=100000003ffff803, pud=100000003ffff803, pmd=100000003fffa803, pte=006800009c090f13
Internal error: ttbr address size fault: 96000000 [#1] PREEMPT SMP
...
Call trace:
pl011_stop_rx+0x70/0x80
tty_port_shutdown+0x7c/0xb4
tty_port_close+0x60/0xcc
uart_close+0x34/0x8c
tty_release+0x144/0x4c0
__fput+0x78/0x220
____fput+0x1c/0x30
task_work_run+0x88/0xc0
do_notify_resume+0x8d0/0x123c
el0_svc+0xa8/0xc0
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x1a0/0x1a4
Code: b9000083 b901f001 794038a0 8b000042 (b9000041)
---[ end trace 83dd93df15c3216f ]---
note: bootlogd[132] exited with preempt_count 1
/etc/rcS.d/S07bootlogd: line 47: 132 Segmentation fault start-stop-daemon
This has been discussed in the Xen community, and we think it should fix
this in Linux. See [2] for more information.
[1] https://developer.arm.com/documentation/den0094/c/?lang=en
[2] https://lists.xenproject.org/archives/html/xen-devel/2022-11/msg00543.html |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rsi: Fix memory leak in rsi_coex_attach()
The coex_cb needs to be freed when rsi_create_kthread() failed in
rsi_coex_attach(). |
| In the Linux kernel, the following vulnerability has been resolved:
drivers: perf: marvell_cn10k: Fix hotplug callback leak in tad_pmu_init()
tad_pmu_init() won't remove the callback added by cpuhp_setup_state_multi()
when platform_driver_register() failed. Remove the callback by
cpuhp_remove_multi_state() in fail path.
Similar to the handling of arm_ccn_init() in commit 26242b330093 ("bus:
arm-ccn: Prevent hotplug callback leak") |
