| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| The MCTP-over-I2C+GPIO target binding in Zephyr (subsys/pmci/mctp/mctp_i2c_gpio_target.c) processes pseudo-register writes from an I2C bus master byte-by-byte in mctp_i2c_gpio_target_write_received() without validating the order or the receive buffer. In the affected versions the MCTP_I2C_GPIO_RX_MSG_ADDR (data) handler dereferences and writes through b->rx_pkt without checking that the receive buffer was allocated: a controller that selects the data register and writes a byte without first sending the length register (which is what allocates the buffer) causes a write of an attacker-chosen byte through a NULL/unallocated mctp_pktbuf pointer (i.e. into a small attacker-advanceable offset above address 0), producing memory corruption or a hard fault.
The same handler also performs a write-then-check bounds test, allowing a one-byte heap overflow at data[255] when more than 255 data bytes are sent.
Because the I2C target callback is invoked with raw bytes supplied by whatever device is the bus master and the binding performs no authentication, a malicious or malfunctioning controller on the bus can trigger these without any prior protocol state, leading to memory corruption and/or denial of service on the target device.
The vulnerable code was introduced when the I2C+GPIO target binding was added and shipped in Zephyr v4.3.0 and v4.4.0. The fix defers allocation to the first data byte with a NULL check, treats a missing length as a zero-sized packet rejected by libmctp, and moves the bounds check before the store. |
| The DesignWare SPI driver (drivers/spi/spi_dw.c) computed the SPI BAUDR clock divider as info->clock_frequency / config->frequency without validating config->frequency.
spi_transceive is a Zephyr __syscall and its verify handler (drivers/spi/spi_handlers.c) copies the caller-supplied spi_config from userspace without checking the frequency field, so a userspace thread that has been granted access to a DesignWare SPI device kernel object can pass frequency = 0 and trigger an unsigned integer divide-by-zero in spi_dw_configure().
On Cortex-M Mainline (SCB->CCR.DIV_0_TRP is set in z_arm_fault_init()) and on ARC (a dedicated __ev_div_zero vector) this raises a CPU exception, resulting in a kernel fault and local denial of service.
The fix rejects zero frequency and frequencies above clock_frequency / 2 (the DesignWare SSI databook minimum SCKDIV of 2) with -EINVAL. The defect affects all Zephyr releases up to and including v4.4.0; exploitation requires CONFIG_USERSPACE=y and an unprivileged thread already granted SPI driver permission. There is no memory-corruption or information-disclosure impact. |
| The Classic (BR/EDR) L2CAP signaling handlers l2cap_br_conf_req() and l2cap_br_conf_rsp() in subsys/bluetooth/host/classic/l2cap_br.c validated the minimum command size against buf->len (the bytes remaining in the whole received PDU) instead of len (the per-command data length from the L2CAP signaling header). Because multiple signaling commands can be packed into one PDU, buf->len may exceed a command's len. An attacker can send a CONF_REQ command with a header length smaller than the configuration-request structure (e.g. 0), followed by another command so that buf->len still satisfies the check. The check then passes incorrectly and opt_len = len - sizeof(*req) underflows the uint16_t to a near-0xFFFF value. The configuration-option loop, which lacks an opt_len-versus-buf->len guard, then walks far past the end of the pooled ACL receive buffer using net_buf pull primitives that perform no runtime bounds check, producing an out-of-bounds read of host memory and, when the out-of-bounds option bytes encode an MTU or flush-timeout option, an out-of-bounds write. The BR/EDR signaling channel is processed before pairing/encryption and an L2CAP channel to an L0 service such as SDP can be opened without pairing, so an unauthenticated peer within radio range that can establish an ACL connection can trigger the flaw, leading to memory corruption and denial of service (host/device crash). The defect is present in released versions including v4.4.0. The fix validates against len instead of buf->len in both handlers. |
| Zephyr's HTTP server (subsys/net/lib/http) provides a static-filesystem resource type (HTTP_RESOURCE_TYPE_STATIC_FS, available when CONFIG_FILE_SYSTEM is enabled) that serves files from a configured root directory. Before this fix, both the HTTP/1 and HTTP/2 front-ends placed the raw, attacker-controlled request path into client->url_buffer (assembled in on_url() for HTTP/1 and copied verbatim from the :path pseudo-header for HTTP/2) without resolving ./.. segments. The static-FS handler then built the on-disk filename by directly concatenating the configured root with that raw URL (snprintk(fname, ..., "%s%s", static_fs_detail->fs_path, client->url_buffer) at http_server_http1.c:603 and http_server_http2.c:490) and opened it with fs_open(fname, FS_O_READ). Because the handler is reached via wildcard/leading-dir (fnmatch FNM_LEADING_DIR) or fallback resource matching, a request such as GET /<prefix>/../../<file> is dispatched to the handler and, after the underlying filesystem (e.g. LittleFS/FAT) resolves the .. segments, escapes the configured web root, letting an unauthenticated remote client read arbitrary readable files on the mounted volume (information disclosure). The HTTP server requires no TLS or authentication to reach this path. The fix adds http_server_remove_dot_segments(), which canonicalizes the path portion of the URL before resource lookup in both protocol handlers, neutralizing the traversal. Affects releases v4.0.0 through v4.4.0 for deployments that register a static-filesystem resource. |
| The Zephyr ADIN2111/ADIN1110 10BASE-T1S/T1L Ethernet driver (drivers/ethernet/eth_adin2111.c) reassembles received Ethernet frames in OPEN Alliance (OA) SPI mode by copying device-supplied 64-byte data chunks into a fixed static buffer ctx->buf of size CONFIG_ETH_ADIN2111_BUFFER_SIZE (default 1524 bytes). In eth_adin2111_oa_data_read(), each valid chunk was memcpy'd into ctx->buf[ctx->scur] and the write cursor scur advanced, with no check that scur + len stayed within the buffer. The number of chunks (up to 255, from the BUFSTS RCA field) and the per-chunk length are taken entirely from the frame data received off the wire; the cursor is only reset on a start-of-frame chunk. An attacker on the single-pair Ethernet segment can therefore send a frame whose reassembled size exceeds the configured buffer, causing the driver's RX offload thread to write attacker-controlled frame bytes past the end of the static buffer into adjacent driver/kernel memory (up to roughly 14.8 KB in the worst case). This is a remotely/adjacently reachable out-of-bounds write (CWE-787) that can corrupt memory and cause denial of service or potentially code execution. The defect was introduced when OA SPI support was added (commit 0ca8b0756b1) and shipped in releases v3.7.0 through v4.4.0. The fix adds a bounds check that drops the oversized frame and resets the cursor before the copy. |
| parse_ipv4() in subsys/net/ip/utils.c (reached via net_ipaddr_parse() for strings of the form "a.b.c.d:port") copies the port substring into a fixed 17-byte stack buffer (char ipaddr[NET_IPV4_ADDR_LEN + 1]) using a length of str_len - end - 1, where str_len is the full, unbounded input length and end is only the (<=15-byte) offset of the ':' delimiter. Because the destination size is never consulted, a crafted address string with a long suffix after the colon (e.g. "1.2.3.4:" followed by hundreds of bytes) causes an out-of-bounds stack write whose length and contents are fully attacker-controlled (memcpy of the suffix plus a trailing NUL), enabling memory corruption and at minimum a denial of service, and potentially control-flow hijack. The parser is reached from the standard socket API (zsock_getaddrinfo / literal-address resolution), DNS server-string configuration, and the eswifi Wi-Fi co-processor DNS-response path, so an application that resolves a network-influenced address string is exposed. The bug was introduced when the parser was added (Zephyr v1.9.0) and shipped in all releases through v4.4.0. The fix removes the unbounded copy and validates the port length before copying into a small dedicated buffer. Note: the equivalent IPv6 "[addr]:port" path in parse_ipv6() retains the same unbounded copy at this commit and remains a separate, still-reachable instance of the defect. |
| The Dhara flash translation layer disk driver (drivers/disk/ftl_dhara.c) implemented the dhara_nand_ callbacks so that, on a flash error, the error code was written unconditionally through the caller-supplied dhara_error_t err pointer (e.g. *err = DHARA_E_ECC in dhara_nand_read, and similar in dhara_nand_erase/prog/copy).
The upstream Dhara library calls these callbacks with err == NULL along its journal-resume binary search: find_last_checkblock() invokes find_checkblock(j, mid, &found, NULL), which forwards the NULL pointer into dhara_nand_read(). This path runs during disk_ftl_access_init() -> dhara_map_resume() whenever the FTL disk is mounted/initialised.
If a flash read error (uncorrectable ECC, bad block, controller error) occurs on one of the probed checkpoint pages, the driver dereferences and writes to NULL, faulting the kernel (denial of service). The trigger is conditioned on the NAND medium content/health, which can be influenced by media wear, induced faults, or a corrupted/crafted on-flash image.
The fix routes all error assignments through the library's NULL-safe dhara_set_error() helper. Affects Zephyr v4.4.0, where the driver was introduced. |
| The MAX32xxx USB device controller driver (drivers/usb/udc/udc_max32.c, compatible adi_max32_usbhs) dereferenced an endpoint buffer in its OUT and IN transfer-completion handlers without checking it for NULL. udc_event_xfer_out_done() called net_buf_add(buf, ep_request->actlen) immediately after buf = udc_buf_get(ep_cfg), where udc_buf_get() returns NULL when the endpoint FIFO is empty.
A transfer-completion event is queued from interrupt context and processed asynchronously by the driver thread; between queuing and processing, the endpoint FIFO can be drained by host-controlled control flow — in particular udc_setup_received() drains the EP0 OUT/IN FIFOs whenever a new SETUP packet arrives, and dequeue/disable/purge paths drain it likewise.
A USB host that aborts an in-flight EP0 control transfer with a new SETUP packet (legal USB behavior) can therefore cause a stale XFER_OUT_DONE event to be processed against an empty FIFO, producing net_buf_add(NULL, ...), a near-NULL pointer dereference that faults and crashes the device. No authentication is required; the attacker is the USB host the device is connected to (physical bus access). Impact is denial of service (device crash).
The defect was introduced when the MAX32 UDC driver was added and shipped in Zephyr v4.4.0. The fix adds NULL-buffer checks that return early with UDC_EVT_ERROR/-ENOBUFS in both the OUT-done and IN-done handlers. |
| Zephyr's DNS resolver detects mDNS (.local) queries in dns_resolve_name_internal() (subsys/net/lib/dns/resolve.c) with memcmp(strrchr(query, '.'), ".local", 7), which always reads a fixed 7 bytes from the suffix pointer. When the resolved hostname's final label is shorter than 7 bytes (e.g. names ending in .org, .com, .net, .io, or a trailing dot), the comparison reads 1-2 bytes past the string's NUL terminator.
The hostname (query) is the caller-supplied name passed through the standard getaddrinfo()/dns_get_addr_info()/dns_resolve_name() path and is influenceable by operators or remote inputs (server names from configuration, parsed URLs, or app-facing interfaces).
On a tightly-sized buffer with no slack (for example a userspace getaddrinfo call where the hostname is copied with k_usermode_string_alloc_copy to exactly strlen+1 bytes), the over-read crosses the allocation boundary; if that boundary is unmapped (guard page, memory-domain boundary under MPU, or an address sanitizer) the over-read faults, causing a denial of service. The over-read bytes are never returned, so there is no information disclosure.
The flaw is compiled only when CONFIG_MDNS_RESOLVER is enabled, exists since v1.10.0, and is fixed by replacing the fixed-length memcmp with a NUL-safe strcmp(ptr, ".local"). |
| mcumgr_serial_process_frag() in subsys/mgmt/mcumgr/transport/src/serial_util.c calls net_buf_reset() on the result of smp_packet_alloc() before checking it for NULL. smp_packet_alloc() uses net_buf_alloc(K_NO_WAIT) against the shared MCUmgr packet pool (CONFIG_MCUMGR_TRANSPORT_NETBUF_COUNT, default 4), which returns NULL when the pool is exhausted. In default builds the __ASSERT_NO_MSG in net_buf_reset is a no-op, so net_buf_simple_reset writes through the NULL pointer (buf->len = 0; buf->data = buf->__buf), causing a fault/crash.
The fragment data reaches this code from attacker-controlled bytes on the MCUmgr serial/UART/shell-console transports (smp_uart.c, smp_raw_uart.c, smp_shell.c), and a fresh buffer is allocated at the start of essentially every new packet. An attacker on the serial/console link can flood the transport to drive the 4-entry buffer pool to exhaustion and induce the NULL dereference, crashing the device (denial of service).
The defect was introduced after the original MCUmgr rework and shipped in Zephyr v4.4.0. The fix moves the NULL check ahead of net_buf_reset. |
| The Zephyr Bluetooth LE Audio Basic Audio Profile (BAP) unicast client mishandles peer-supplied ASE state notifications. In unicast_client_ep_qos_state() (subsys/bluetooth/audio/bap_unicast_client.c), the handler writes attacker-controlled QoS fields (interval, framing, phy, sdu, rtn, latency, pd) through the stream->qos pointer with only a stream != NULL guard. stream->qos is NULL for any stream that has been codec-configured via bt_bap_stream_config() but not yet added to a unicast group (it is set only by unicast_group_add_stream()).
A malicious or buggy remote ASCS server, to which the local device is connected as a BAP unicast client, can send a GATT notification announcing the ASE has entered the QoS Configured state while the local endpoint is still in the Codec Configured state — a transition the dispatcher explicitly permits — during that window, causing a write through a NULL pointer and a crash (denial of service). The data written is itself remote-controlled.
The defect shipped in v4.3.0 and v4.4.0 (and earlier). The fix re-points all BAP QoS storage to the always-valid embedded ep->qos struct, eliminating the NULL dereference. |
| The USB CDC-NCM device class (subsys/usb/device_next/class/usbd_cdc_ncm.c) ignores the return value of usbd_ep_enqueue() in its ethernet transmit callback cdc_ncm_send(). When the enqueue fails, the function still calls k_sem_take(&data->sync_sem, K_FOREVER), blocking on a completion semaphore that is only ever signaled from the bulk-IN transfer-completion callback. Because nothing was enqueued, that callback never fires and the calling thread — a shared network traffic-class TX thread — deadlocks permanently while holding the interface TX lock, halting transmission until reboot (and leaking the transmit buffer).
The enqueue fails under conditions controlled by the attached USB host: usbd_ep_enqueue() returns -EPERM whenever the bus is suspended (a standard, persistent host operation), and the underlying udc_ep_enqueue() returns -EPERM/-ENODEV on disconnect, bus reset, or endpoint disable. The cdc_ncm_send() guard only checks the DATA_IFACE_ENABLED and IFACE_UP flags, not the suspended state, so a packet transmitted while the host holds the bus suspended reaches the failing enqueue and deadlocks the TX path.
The realistic trigger is a bus suspend that occurs while the exported network interface is active and has traffic to send — host sleep, USB selective/auto-suspend, or hub power management — after which any device-originated packet deadlocks the path, recoverable only by reboot. The impact is a persistent loss of the virtual network connection between the host's NCM interface and the Zephyr device; because the deadlocked thread is a shared traffic-class TX thread, egress on other network interfaces can stall as well. There is no memory corruption or information disclosure.
The defect was introduced with the CDC-NCM driver and shipped in releases through v4.4.0; it is fixed by checking the usbd_ep_enqueue() return value and freeing the buffer before the blocking wait. |
| Zephyr's BSD-sockets getaddrinfo() implementation (subsys/net/lib/sockets/getaddrinfo.c) passes a pointer to a stack-allocated state object (struct getaddrinfo_state ai_state) as the user_data of an asynchronous DNS resolver query. The socket layer waits on a semaphore with a timeout deliberately set slightly longer than the resolver's own per-query timeout. When that semaphore wait nonetheless times out (-EAGAIN) - which can occur when the resolver's timeout work is delayed by workqueue contention, or in the documented multi-retry configuration where CONFIG_NET_SOCKETS_DNS_TIMEOUT exceeds CONFIG_NET_SOCKETS_DNS_BACKOFF_INTERVAL - the pre-fix code retries the query (goto again) without cancelling the previous one and without resetting the semaphore.
The previous query slot remains active in the resolver with its callback and the stack pointer as user_data, and ai_state->dns_id is overwritten so the stale query can no longer be cancelled. A subsequent DNS response delivered over UDP and matched by its 16-bit transaction id (in dispatcher_cb()/dns_read()), or the resolver's own delayed query-timeout work, then invokes dns_resolve_cb() against the now out-of-scope stack frame, writing through the stale pointer (state->status, state->idx, state->ai_arr[], and k_sem_give()).
Because the triggering response is network-delivered and its 16-bit id is spoofable/replayable by an on- or off-path attacker, this is a network-influenceable use-after-return that can corrupt reused stack memory, leading to crashes/denial of service or memory corruption.
The fix cancels the timed-out query by name and type before retrying and resets the local semaphore, eliminating the stale callback path. Affected: Zephyr v4.0.0 through v4.4.0. |
| The Microchip SERCOM-G1 UART driver (drivers/serial/uart_mchp_sercom_g1.c), used by the PIC32CM-JH SoC family, contains an out-of-bounds write in its asynchronous (DMA) receive path. When uart_rx_enable() is invoked with a one-byte receive buffer (len == 1) and CONFIG_UART_MCHP_ASYNC is enabled, the RX-complete ISR starts a single-beat DMA transfer while a received byte is already pending in the SERCOM DATA register. On this SoC the peripheral-triggered DMA start sequencing then writes one byte past the end of the caller-supplied buffer (CWE-787).
The overflowed byte's value is the UART RX data supplied by the connected serial peer (adjacent attacker), while its size and location are fixed at one byte immediately after the buffer.
Exploitation requires the async UART config (not enabled by default on the in-tree PIC32CM-JH boards) and a consumer that enables RX with a one-byte buffer; impact is limited single-byte memory corruption adjacent to the RX buffer (possible crash / denial of service).
The defect shipped in v4.4.0. The fix reads the first byte with the CPU and, for one-byte buffers, performs no DMA at all; for larger buffers it sizes the DMA for the remaining len-1 bytes. |
| Zephyr's IP socket recvmsg() implementation (subsys/net/lib/sockets/sockets_inet.c, insert_pktinfo()) validated the user-supplied ancillary (msg_control) buffer using only the payload length (msg->msg_controllen < pktinfo_len) before writing a full control message consisting of an aligned cmsg header plus the payload. Because the check omitted the cmsg header size, a control buffer whose length falls in the under-checked window (e.g. 16-27 bytes for IPv4 IP_PKTINFO on a 64-bit target, where a single element actually occupies 28 bytes) passes the guard yet causes a fixed-size out-of-bounds write of up to one cmsg header (~12 bytes) past the end of the buffer.
Under CONFIG_USERSPACE the recvmsg verifier allocates a kernel-heap copy of the control buffer sized to msg_controllen and runs the implementation against it, so the overflow corrupts kernel heap memory and is triggerable from an unprivileged userspace thread; in supervisor mode it corrupts the caller's buffer.
The path is reachable on a UDP/IP socket with IP_PKTINFO/IPV6_RECVPKTINFO (or hoplimit/timestamping) enabled when the application calls recvmsg() with an undersized control buffer and a datagram is received; part of the overwritten bytes (the destination IP in ipi_addr) is influenced by the received packet.
The fix makes the capacity check use NET_CMSG_SPACE(pktinfo_len) (aligned header + aligned data) and returns -ENOMEM when the buffer is too small. Affected: v3.6.0 through v4.4.0. |
| The Zephyr PL011 UART driver (drivers/serial/uart_pl011.c) contains an unbounded software loop in pl011_irq_tx_enable() that repeatedly invokes the interrupt-driven application callback while the TX interrupt mask bit (PL011_IMSC_TXIM) is set, to work around the controller's level-transition TX-interrupt behavior.
When CTS hardware flow control is enabled (devicetree hw-flow-control or runtime UART_CFG_FLOW_CTRL_RTS_CTS) and the wired serial peer de-asserts CTS, the controller stops draining the TX FIFO; pl011_fifo_fill() then returns 0 on every call while the application still has pending data and therefore never disables the TX interrupt. The loop condition never clears, so the thread that called uart_irq_tx_enable() (e.g. h4_send() in the Bluetooth HCI H4 driver) spins indefinitely, hanging the executing context and stalling the transport — a denial of service (CWE-835).
An attacker controlling the device attached to the UART's CTS line can trigger the hang by withholding CTS during transmission. Because that peer is the device wired to the UART — which may be a removable or external module (e.g. an off-board Bluetooth controller on the HCI H4 link) rather than a permanently-bonded on-PCB part — the attack vector is scored Adjacent (AV:A) rather than Physical; the security subcommittee should confirm the vector against the specific deployment. Impact is availability only; there is no memory-safety, confidentiality, or integrity consequence.
The vulnerable loop was introduced in commit b783bc8448ef (Feb 2025) and shipped in releases v4.1.0 through v4.4.0. The fix breaks out of the loop when CTS is blocking and arms the CTS modem-status interrupt to resume transmission when CTS re-asserts. |
| Zephyr's Bluetooth Classic Hands-Free Profile (HFP) Hands-Free role parser (subsys/bluetooth/host/classic/hfp_hf.c) contains an out-of-bounds write. During Service Level Connection setup the HF sends AT+CIND=? and parses the AG's +CIND: response in cind_handle(), which assigns a per-entry counter index and calls cind_handle_values() for each list element. cind_handle_values() then wrote hf->ind_table[index] = i without verifying that index is within the 20-element int8_t ind_table[] array of struct bt_hfp_hf. Because the parser places no cap on the number of +CIND: list entries, a remote Attendant Gateway (a malicious, compromised, or spoofed peer the device connects to over Bluetooth) can send a response with more than 20 recognized indicator entries and drive index arbitrarily large, writing a small attacker-positioned value past the array into adjacent struct fields (feature masks, SDP/version state, the calls[] array, work/atomic bookkeeping) and potentially beyond the static connection pool slot. This yields memory corruption and at least denial of service of the Bluetooth host, triggered by a single malformed AT response with no user interaction. The sibling consumer ag_indicator_handle_values() already performed the equivalent bounds check; this commit adds the same index >= ARRAY_SIZE(hf->ind_table) guard to close the gap. Affects builds with CONFIG_BT_HFP_HF enabled; introduced with the original HFP HF CIND parser (~v1.7) and present through v4.4.0. |
| Zephyr's IPv6 Neighbor Discovery send paths (net_ipv6_send_na, net_ipv6_send_ns, net_ipv6_send_rs in subsys/net/ip/ipv6_nbr.c) updated the per-interface ICMP-sent statistics by calling net_pkt_iface(pkt) after net_send_data(pkt) had already returned successfully. On the success path the network stack owns and releases the packet's reference (the L2/driver send unrefs it, e.g. ethernet_send -> net_pkt_unref), so for a freshly allocated packet with refcount 1 the net_pkt slab block can be freed before the statistics line runs (synchronously when no TX queue thread is configured, or via a concurrent TX thread otherwise).
The subsequent net_pkt_iface(pkt) reads pkt->iface from the freed slab block, and with CONFIG_NET_STATISTICS_PER_INTERFACE enabled that loaded pointer is dereferenced to increment iface->stats.icmp.sent, a use-after-free (CWE-416). If the slab block was reallocated in the meantime the read/increment targets unrelated or attacker-influenced memory, yielding corrupted statistics, a fault/crash (denial of service), or potential limited memory corruption.
The vulnerable Neighbor Advertisement path is reachable by any unauthenticated on-link node simply by sending ICMPv6 Neighbor Solicitations to a Zephyr node with native IPv6 enabled (handle_ns_input -> net_ipv6_send_na).
Affected from v3.3.0 through v4.4.0; the fix uses the already-available iface argument instead of touching the sent packet. Configurations without per-interface statistics dereference only a global counter and are not affected by the memory-safety aspect. |
| In Zephyr's native IPv4 stack, icmpv4_handle_echo_request() in subsys/net/ip/icmpv4.c builds an echo-reply packet (reply), hands it to net_try_send_data(), and then, on success, calls net_stats_update_icmp_sent(net_pkt_iface(reply)). net_try_send_data() transfers ownership of reply to the TX path (net_if_try_queue_tx -> net_if_tx -> L2/driver send, or the asynchronous net_if_tx_thread), which can unref it to refcount 0 and return the struct net_pkt to its slab (net_pkt_unref -> k_mem_slab_free) before the stats line runs. net_core.c documents this exact contract ('the pkt might contain garbage already ... do not use pkt after that call').
The post-send net_pkt_iface(reply) therefore reads reply->iface out of a freed (and possibly already reallocated) net_pkt, a use-after-free read; with CONFIG_NET_STATISTICS_PER_INTERFACE the stats macro additionally increments a counter through that value, i.e. a dereference/write through a stale or recycled-slot pointer.
The path is reached unauthenticated by any remote host that pings the device (net_icmpv4_input -> net_icmp_call_ipv4_handlers -> icmpv4_handle_echo_request) and is gated on CONFIG_NET_STATISTICS_ICMP. Impact is a probabilistic read of recycled packet memory plus a possible wild-pointer write under a timing race, leading most likely to corrupted interface statistics or a remotely triggerable crash (DoS).
The defect was introduced in 2019 (v1.14) and is present through v4.4.0. The companion change in net_icmpv4_send_error() is not a use-after-free because it reads net_pkt_iface(orig), the caller-owned received packet, which stays alive across the send. The fix caches the interface pointer from the live received packet before sending and uses it for the post-send stats updates. |
| On Xtensa targets with CONFIG_USERSPACE and CONFIG_XTENSA_MMU, the page-table code (arch/xtensa/core/ptables.c) maintains a global list, xtensa_domain_list, of active memory domains using a list node embedded inside the caller-owned struct k_mem_domain. When a domain is destroyed via k_mem_domain_deinit() -> arch_mem_domain_deinit(), the page tables are torn down and domain->arch.ptables is set to NULL, but the domain's node was not removed from xtensa_domain_list. The freed/deinitialized domain therefore remained linked into the global list as a dangling pointer into caller-owned storage that may then be freed or reused.
Any subsequent arch_mem_map()/arch_mem_unmap() operation (widely invoked by kernel memory-mapping and demand-paging code) traverses the stale node and dereferences domain->ptables: at minimum a NULL pointer dereference causing a fatal MMU exception (denial of service), and if the k_mem_domain storage has been freed or reused, a use-after-free in which a stale/controlled ptables value is dereferenced and written through during the page-table walk (l2_page_table_map writes l1_table[...] and l2_table[...], and xtensa_mmu_compute_domain_regs writes into the domain struct and the L1 table), yielding page-table memory corruption that can undermine userspace isolation.
The vulnerable path is reachable only from privileged kernel/supervisor code (k_mem_domain_deinit is not a syscall), not directly from unprivileged user threads or remotely. Affected: Zephyr v4.4.0 (the Xtensa memory-domain de-initialization feature was introduced in commit 3032b58f52d and first shipped in v4.4.0); fixed on main by adding sys_slist_find_and_remove() in arch_mem_domain_deinit(). The Xtensa MPU path is unaffected. |
