| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel: Fix IA32_PMC_x_CFG_B MSRs access error
When running perf_fuzzer on PTL, sometimes the below "unchecked MSR
access error" is seen when accessing IA32_PMC_x_CFG_B MSRs.
[ 55.611268] unchecked MSR access error: WRMSR to 0x1986 (tried to write 0x0000000200000001) at rIP: 0xffffffffac564b28 (native_write_msr+0x8/0x30)
[ 55.611280] Call Trace:
[ 55.611282] <TASK>
[ 55.611284] ? intel_pmu_config_acr+0x87/0x160
[ 55.611289] intel_pmu_enable_acr+0x6d/0x80
[ 55.611291] intel_pmu_enable_event+0xce/0x460
[ 55.611293] x86_pmu_start+0x78/0xb0
[ 55.611297] x86_pmu_enable+0x218/0x3a0
[ 55.611300] ? x86_pmu_enable+0x121/0x3a0
[ 55.611302] perf_pmu_enable+0x40/0x50
[ 55.611307] ctx_resched+0x19d/0x220
[ 55.611309] __perf_install_in_context+0x284/0x2f0
[ 55.611311] ? __pfx_remote_function+0x10/0x10
[ 55.611314] remote_function+0x52/0x70
[ 55.611317] ? __pfx_remote_function+0x10/0x10
[ 55.611319] generic_exec_single+0x84/0x150
[ 55.611323] smp_call_function_single+0xc5/0x1a0
[ 55.611326] ? __pfx_remote_function+0x10/0x10
[ 55.611329] perf_install_in_context+0xd1/0x1e0
[ 55.611331] ? __pfx___perf_install_in_context+0x10/0x10
[ 55.611333] __do_sys_perf_event_open+0xa76/0x1040
[ 55.611336] __x64_sys_perf_event_open+0x26/0x30
[ 55.611337] x64_sys_call+0x1d8e/0x20c0
[ 55.611339] do_syscall_64+0x4f/0x120
[ 55.611343] entry_SYSCALL_64_after_hwframe+0x76/0x7e
On PTL, GP counter 0 and 1 doesn't support auto counter reload feature,
thus it would trigger a #GP when trying to write 1 on bit 0 of CFG_B MSR
which requires to enable auto counter reload on GP counter 0.
The root cause of causing this issue is the check for auto counter
reload (ACR) counter mask from user space is incorrect in
intel_pmu_acr_late_setup() helper. It leads to an invalid ACR counter
mask from user space could be set into hw.config1 and then written into
CFG_B MSRs and trigger the MSR access warning.
e.g., User may create a perf event with ACR counter mask (config2=0xcb),
and there is only 1 event created, so "cpuc->n_events" is 1.
The correct check condition should be "i + idx >= cpuc->n_events"
instead of "i + idx > cpuc->n_events" (it looks a typo). Otherwise,
the counter mask would traverse twice and an invalid "cpuc->assign[1]"
bit (bit 0) is set into hw.config1 and cause MSR accessing error.
Besides, also check if the ACR counter mask corresponding events are
ACR events. If not, filter out these counter mask. If a event is not a
ACR event, it could be scheduled to an HW counter which doesn't support
ACR. It's invalid to add their counter index in ACR counter mask.
Furthermore, remove the WARN_ON_ONCE() since it's easily triggered as
user could set any invalid ACR counter mask and the warning message
could mislead users. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-mq: fix potential deadlock while nr_requests grown
Allocate and free sched_tags while queue is freezed can deadlock[1],
this is a long term problem, hence allocate memory before freezing
queue and free memory after queue is unfreezed.
[1] https://lore.kernel.org/all/0659ea8d-a463-47c8-9180-43c719e106eb@linux.ibm.com/ |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/atom: Check kcalloc() for WS buffer in amdgpu_atom_execute_table_locked()
kcalloc() may fail. When WS is non-zero and allocation fails, ectx.ws
remains NULL while ectx.ws_size is set, leading to a potential NULL
pointer dereference in atom_get_src_int() when accessing WS entries.
Return -ENOMEM on allocation failure to avoid the NULL dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: Don't call reqsk_fastopen_remove() in tcp_conn_request().
syzbot reported the splat below in tcp_conn_request(). [0]
If a listener is close()d while a TFO socket is being processed in
tcp_conn_request(), inet_csk_reqsk_queue_add() does not set reqsk->sk
and calls inet_child_forget(), which calls tcp_disconnect() for the
TFO socket.
After the cited commit, tcp_disconnect() calls reqsk_fastopen_remove(),
where reqsk_put() is called due to !reqsk->sk.
Then, reqsk_fastopen_remove() in tcp_conn_request() decrements the
last req->rsk_refcnt and frees reqsk, and __reqsk_free() at the
drop_and_free label causes the refcount underflow for the listener
and double-free of the reqsk.
Let's remove reqsk_fastopen_remove() in tcp_conn_request().
Note that other callers make sure tp->fastopen_rsk is not NULL.
[0]:
refcount_t: underflow; use-after-free.
WARNING: CPU: 12 PID: 5563 at lib/refcount.c:28 refcount_warn_saturate (lib/refcount.c:28)
Modules linked in:
CPU: 12 UID: 0 PID: 5563 Comm: syz-executor Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/12/2025
RIP: 0010:refcount_warn_saturate (lib/refcount.c:28)
Code: ab e8 8e b4 98 ff 0f 0b c3 cc cc cc cc cc 80 3d a4 e4 d6 01 00 75 9c c6 05 9b e4 d6 01 01 48 c7 c7 e8 df fb ab e8 6a b4 98 ff <0f> 0b e9 03 5b 76 00 cc 80 3d 7d e4 d6 01 00 0f 85 74 ff ff ff c6
RSP: 0018:ffffa79fc0304a98 EFLAGS: 00010246
RAX: d83af4db1c6b3900 RBX: ffff9f65c7a69020 RCX: d83af4db1c6b3900
RDX: 0000000000000000 RSI: 00000000ffff7fff RDI: ffffffffac78a280
RBP: 000000009d781b60 R08: 0000000000007fff R09: ffffffffac6ca280
R10: 0000000000017ffd R11: 0000000000000004 R12: ffff9f65c7b4f100
R13: ffff9f65c7d23c00 R14: ffff9f65c7d26000 R15: ffff9f65c7a64ef8
FS: 00007f9f962176c0(0000) GS:ffff9f65fcf00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000200000000180 CR3: 000000000dbbe006 CR4: 0000000000372ef0
Call Trace:
<IRQ>
tcp_conn_request (./include/linux/refcount.h:400 ./include/linux/refcount.h:432 ./include/linux/refcount.h:450 ./include/net/sock.h:1965 ./include/net/request_sock.h:131 net/ipv4/tcp_input.c:7301)
tcp_rcv_state_process (net/ipv4/tcp_input.c:6708)
tcp_v6_do_rcv (net/ipv6/tcp_ipv6.c:1670)
tcp_v6_rcv (net/ipv6/tcp_ipv6.c:1906)
ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:438)
ip6_input (net/ipv6/ip6_input.c:500)
ipv6_rcv (net/ipv6/ip6_input.c:311)
__netif_receive_skb (net/core/dev.c:6104)
process_backlog (net/core/dev.c:6456)
__napi_poll (net/core/dev.c:7506)
net_rx_action (net/core/dev.c:7569 net/core/dev.c:7696)
handle_softirqs (kernel/softirq.c:579)
do_softirq (kernel/softirq.c:480)
</IRQ> |
| In the Linux kernel, the following vulnerability has been resolved:
jfs: Verify inode mode when loading from disk
The inode mode loaded from corrupted disk can be invalid. Do like what
commit 0a9e74051313 ("isofs: Verify inode mode when loading from disk")
does. |
| In the Linux kernel, the following vulnerability has been resolved:
gve: Implement gettimex64 with -EOPNOTSUPP
gve implemented a ptp_clock for sole use of do_aux_work at this time.
ptp_clock_gettime() and ptp_sys_offset() assume every ptp_clock has
implemented either gettimex64 or gettime64. Stub gettimex64 and return
-EOPNOTSUPP to prevent NULL dereferencing. |
| In the Linux kernel, the following vulnerability has been resolved:
orangefs: fix xattr related buffer overflow...
Willy Tarreau <w@1wt.eu> forwarded me a message from
Disclosure <disclosure@aisle.com> with the following
warning:
> The helper `xattr_key()` uses the pointer variable in the loop condition
> rather than dereferencing it. As `key` is incremented, it remains non-NULL
> (until it runs into unmapped memory), so the loop does not terminate on
> valid C strings and will walk memory indefinitely, consuming CPU or hanging
> the thread.
I easily reproduced this with setfattr and getfattr, causing a kernel
oops, hung user processes and corrupted orangefs files. Disclosure
sent along a diff (not a patch) with a suggested fix, which I based
this patch on.
After xattr_key started working right, xfstest generic/069 exposed an
xattr related memory leak that lead to OOM. xattr_key returns
a hashed key. When adding xattrs to the orangefs xattr cache, orangefs
used hash_add, a kernel hashing macro. hash_add also hashes the key using
hash_log which resulted in additions to the xattr cache going to the wrong
hash bucket. generic/069 tortures a single file and orangefs does a
getattr for the xattr "security.capability" every time. Orangefs
negative caches on xattrs which includes a kmalloc. Since adds to the
xattr cache were going to the wrong bucket, every getattr for
"security.capability" resulted in another kmalloc, none of which were
ever freed.
I changed the two uses of hash_add to hlist_add_head instead
and the memory leak ceased and generic/069 quit throwing furniture. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: fix crash while sending Action Frames in standalone AP Mode
Currently, whenever there is a need to transmit an Action frame,
the brcmfmac driver always uses the P2P vif to send the "actframe" IOVAR to
firmware. The P2P interfaces were available when wpa_supplicant is managing
the wlan interface.
However, the P2P interfaces are not created/initialized when only hostapd
is managing the wlan interface. And if hostapd receives an ANQP Query REQ
Action frame even from an un-associated STA, the brcmfmac driver tries
to use an uninitialized P2P vif pointer for sending the IOVAR to firmware.
This NULL pointer dereferencing triggers a driver crash.
[ 1417.074538] Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000000
[...]
[ 1417.075188] Hardware name: Raspberry Pi 4 Model B Rev 1.5 (DT)
[...]
[ 1417.075653] Call trace:
[ 1417.075662] brcmf_p2p_send_action_frame+0x23c/0xc58 [brcmfmac]
[ 1417.075738] brcmf_cfg80211_mgmt_tx+0x304/0x5c0 [brcmfmac]
[ 1417.075810] cfg80211_mlme_mgmt_tx+0x1b0/0x428 [cfg80211]
[ 1417.076067] nl80211_tx_mgmt+0x238/0x388 [cfg80211]
[ 1417.076281] genl_family_rcv_msg_doit+0xe0/0x158
[ 1417.076302] genl_rcv_msg+0x220/0x2a0
[ 1417.076317] netlink_rcv_skb+0x68/0x140
[ 1417.076330] genl_rcv+0x40/0x60
[ 1417.076343] netlink_unicast+0x330/0x3b8
[ 1417.076357] netlink_sendmsg+0x19c/0x3f8
[ 1417.076370] __sock_sendmsg+0x64/0xc0
[ 1417.076391] ____sys_sendmsg+0x268/0x2a0
[ 1417.076408] ___sys_sendmsg+0xb8/0x118
[ 1417.076427] __sys_sendmsg+0x90/0xf8
[ 1417.076445] __arm64_sys_sendmsg+0x2c/0x40
[ 1417.076465] invoke_syscall+0x50/0x120
[ 1417.076486] el0_svc_common.constprop.0+0x48/0xf0
[ 1417.076506] do_el0_svc+0x24/0x38
[ 1417.076525] el0_svc+0x30/0x100
[ 1417.076548] el0t_64_sync_handler+0x100/0x130
[ 1417.076569] el0t_64_sync+0x190/0x198
[ 1417.076589] Code: f9401e80 aa1603e2 f9403be1 5280e483 (f9400000)
Fix this, by always using the vif corresponding to the wdev on which the
Action frame Transmission request was initiated by the userspace. This way,
even if P2P vif is not available, the IOVAR is sent to firmware on AP vif
and the ANQP Query RESP Action frame is transmitted without crashing the
driver.
Move init_completion() for "send_af_done" from brcmf_p2p_create_p2pdev()
to brcmf_p2p_attach(). Because the former function would not get executed
when only hostapd is managing wlan interface, and it is not safe to do
reinit_completion() later in brcmf_p2p_tx_action_frame(), without any prior
init_completion().
And in the brcmf_p2p_tx_action_frame() function, the condition check for
P2P Presence response frame is not needed, since the wpa_supplicant is
properly sending the P2P Presense Response frame on the P2P-GO vif instead
of the P2P-Device vif.
[Cc stable] |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: release path before inode lookup during the ino lookup ioctl
During the ino lookup ioctl we can end up calling btrfs_iget() to get an
inode reference while we are holding on a root's btree. If btrfs_iget()
needs to lookup the inode from the root's btree, because it's not
currently loaded in memory, then it will need to lock another or the
same path in the same root btree. This may result in a deadlock and
trigger the following lockdep splat:
WARNING: possible circular locking dependency detected
6.5.0-rc7-syzkaller-00004-gf7757129e3de #0 Not tainted
------------------------------------------------------
syz-executor277/5012 is trying to acquire lock:
ffff88802df41710 (btrfs-tree-01){++++}-{3:3}, at: __btrfs_tree_read_lock+0x2f/0x220 fs/btrfs/locking.c:136
but task is already holding lock:
ffff88802df418e8 (btrfs-tree-00){++++}-{3:3}, at: __btrfs_tree_read_lock+0x2f/0x220 fs/btrfs/locking.c:136
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (btrfs-tree-00){++++}-{3:3}:
down_read_nested+0x49/0x2f0 kernel/locking/rwsem.c:1645
__btrfs_tree_read_lock+0x2f/0x220 fs/btrfs/locking.c:136
btrfs_search_slot+0x13a4/0x2f80 fs/btrfs/ctree.c:2302
btrfs_init_root_free_objectid+0x148/0x320 fs/btrfs/disk-io.c:4955
btrfs_init_fs_root fs/btrfs/disk-io.c:1128 [inline]
btrfs_get_root_ref+0x5ae/0xae0 fs/btrfs/disk-io.c:1338
btrfs_get_fs_root fs/btrfs/disk-io.c:1390 [inline]
open_ctree+0x29c8/0x3030 fs/btrfs/disk-io.c:3494
btrfs_fill_super+0x1c7/0x2f0 fs/btrfs/super.c:1154
btrfs_mount_root+0x7e0/0x910 fs/btrfs/super.c:1519
legacy_get_tree+0xef/0x190 fs/fs_context.c:611
vfs_get_tree+0x8c/0x270 fs/super.c:1519
fc_mount fs/namespace.c:1112 [inline]
vfs_kern_mount+0xbc/0x150 fs/namespace.c:1142
btrfs_mount+0x39f/0xb50 fs/btrfs/super.c:1579
legacy_get_tree+0xef/0x190 fs/fs_context.c:611
vfs_get_tree+0x8c/0x270 fs/super.c:1519
do_new_mount+0x28f/0xae0 fs/namespace.c:3335
do_mount fs/namespace.c:3675 [inline]
__do_sys_mount fs/namespace.c:3884 [inline]
__se_sys_mount+0x2d9/0x3c0 fs/namespace.c:3861
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
-> #0 (btrfs-tree-01){++++}-{3:3}:
check_prev_add kernel/locking/lockdep.c:3142 [inline]
check_prevs_add kernel/locking/lockdep.c:3261 [inline]
validate_chain kernel/locking/lockdep.c:3876 [inline]
__lock_acquire+0x39ff/0x7f70 kernel/locking/lockdep.c:5144
lock_acquire+0x1e3/0x520 kernel/locking/lockdep.c:5761
down_read_nested+0x49/0x2f0 kernel/locking/rwsem.c:1645
__btrfs_tree_read_lock+0x2f/0x220 fs/btrfs/locking.c:136
btrfs_tree_read_lock fs/btrfs/locking.c:142 [inline]
btrfs_read_lock_root_node+0x292/0x3c0 fs/btrfs/locking.c:281
btrfs_search_slot_get_root fs/btrfs/ctree.c:1832 [inline]
btrfs_search_slot+0x4ff/0x2f80 fs/btrfs/ctree.c:2154
btrfs_lookup_inode+0xdc/0x480 fs/btrfs/inode-item.c:412
btrfs_read_locked_inode fs/btrfs/inode.c:3892 [inline]
btrfs_iget_path+0x2d9/0x1520 fs/btrfs/inode.c:5716
btrfs_search_path_in_tree_user fs/btrfs/ioctl.c:1961 [inline]
btrfs_ioctl_ino_lookup_user+0x77a/0xf50 fs/btrfs/ioctl.c:2105
btrfs_ioctl+0xb0b/0xd40 fs/btrfs/ioctl.c:4683
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl+0xf8/0x170 fs/ioctl.c:856
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
other info
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
media: tuners: qt1010: replace BUG_ON with a regular error
BUG_ON is unnecessary here, and in addition it confuses smatch.
Replacing this with an error return help resolve this smatch
warning:
drivers/media/tuners/qt1010.c:350 qt1010_init() error: buffer overflow 'i2c_data' 34 <= 34 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qedf: Fix NULL dereference in error handling
Smatch reported:
drivers/scsi/qedf/qedf_main.c:3056 qedf_alloc_global_queues()
warn: missing unwind goto?
At this point in the function, nothing has been allocated so we can return
directly. In particular the "qedf->global_queues" have not been allocated
so calling qedf_free_global_queues() will lead to a NULL dereference when
we check if (!gl[i]) and "gl" is NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: Prevent TOCTOU out-of-bounds write
For the following path not holding the sock lock,
sctp_diag_dump() -> sctp_for_each_endpoint() -> sctp_ep_dump()
make sure not to exceed bounds in case the address list has grown
between buffer allocation (time-of-check) and write (time-of-use). |
| In the Linux kernel, the following vulnerability has been resolved:
drivers: perf: marvell_cn10k: Fix hotplug callback leak in tad_pmu_init()
tad_pmu_init() won't remove the callback added by cpuhp_setup_state_multi()
when platform_driver_register() failed. Remove the callback by
cpuhp_remove_multi_state() in fail path.
Similar to the handling of arm_ccn_init() in commit 26242b330093 ("bus:
arm-ccn: Prevent hotplug callback leak") |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rsi: Fix memory leak in rsi_coex_attach()
The coex_cb needs to be freed when rsi_create_kthread() failed in
rsi_coex_attach(). |
| In the Linux kernel, the following vulnerability has been resolved:
serial: amba-pl011: avoid SBSA UART accessing DMACR register
Chapter "B Generic UART" in "ARM Server Base System Architecture" [1]
documentation describes a generic UART interface. Such generic UART
does not support DMA. In current code, sbsa_uart_pops and
amba_pl011_pops share the same stop_rx operation, which will invoke
pl011_dma_rx_stop, leading to an access of the DMACR register. This
commit adds a using_rx_dma check in pl011_dma_rx_stop to avoid the
access to DMACR register for SBSA UARTs which does not support DMA.
When the kernel enables DMA engine with "CONFIG_DMA_ENGINE=y", Linux
SBSA PL011 driver will access PL011 DMACR register in some functions.
For most real SBSA Pl011 hardware implementations, the DMACR write
behaviour will be ignored. So these DMACR operations will not cause
obvious problems. But for some virtual SBSA PL011 hardware, like Xen
virtual SBSA PL011 (vpl011) device, the behaviour might be different.
Xen vpl011 emulation will inject a data abort to guest, when guest is
accessing an unimplemented UART register. As Xen VPL011 is SBSA
compatible, it will not implement DMACR register. So when Linux SBSA
PL011 driver access DMACR register, it will get an unhandled data abort
fault and the application will get a segmentation fault:
Unhandled fault at 0xffffffc00944d048
Mem abort info:
ESR = 0x96000000
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x00: ttbr address size fault
Data abort info:
ISV = 0, ISS = 0x00000000
CM = 0, WnR = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000020e2e000
[ffffffc00944d048] pgd=100000003ffff803, p4d=100000003ffff803, pud=100000003ffff803, pmd=100000003fffa803, pte=006800009c090f13
Internal error: ttbr address size fault: 96000000 [#1] PREEMPT SMP
...
Call trace:
pl011_stop_rx+0x70/0x80
tty_port_shutdown+0x7c/0xb4
tty_port_close+0x60/0xcc
uart_close+0x34/0x8c
tty_release+0x144/0x4c0
__fput+0x78/0x220
____fput+0x1c/0x30
task_work_run+0x88/0xc0
do_notify_resume+0x8d0/0x123c
el0_svc+0xa8/0xc0
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x1a0/0x1a4
Code: b9000083 b901f001 794038a0 8b000042 (b9000041)
---[ end trace 83dd93df15c3216f ]---
note: bootlogd[132] exited with preempt_count 1
/etc/rcS.d/S07bootlogd: line 47: 132 Segmentation fault start-stop-daemon
This has been discussed in the Xen community, and we think it should fix
this in Linux. See [2] for more information.
[1] https://developer.arm.com/documentation/den0094/c/?lang=en
[2] https://lists.xenproject.org/archives/html/xen-devel/2022-11/msg00543.html |
| In the Linux kernel, the following vulnerability has been resolved:
net: netsec: fix error handling in netsec_register_mdio()
If phy_device_register() fails, phy_device_free() need be called to
put refcount, so memory of phy device and device name can be freed
in callback function.
If get_phy_device() fails, mdiobus_unregister() need be called,
or it will cause warning in mdiobus_free() and kobject is leaked. |
| In the Linux kernel, the following vulnerability has been resolved:
fpga: prevent integer overflow in dfl_feature_ioctl_set_irq()
The "hdr.count * sizeof(s32)" multiplication can overflow on 32 bit
systems leading to memory corruption. Use array_size() to fix that. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel/uncore: Fix reference count leak in snr_uncore_mmio_map()
pci_get_device() will increase the reference count for the returned
pci_dev, so snr_uncore_get_mc_dev() will return a pci_dev with its
reference count increased. We need to call pci_dev_put() to decrease the
reference count. Let's add the missing pci_dev_put(). |
| In the Linux kernel, the following vulnerability has been resolved:
hfs: fix OOB Read in __hfs_brec_find
Syzbot reported a OOB read bug:
==================================================================
BUG: KASAN: slab-out-of-bounds in hfs_strcmp+0x117/0x190
fs/hfs/string.c:84
Read of size 1 at addr ffff88807eb62c4e by task kworker/u4:1/11
CPU: 1 PID: 11 Comm: kworker/u4:1 Not tainted
6.1.0-rc6-syzkaller-00308-g644e9524388a #0
Workqueue: writeback wb_workfn (flush-7:0)
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x1b1/0x28e lib/dump_stack.c:106
print_address_description+0x74/0x340 mm/kasan/report.c:284
print_report+0x107/0x1f0 mm/kasan/report.c:395
kasan_report+0xcd/0x100 mm/kasan/report.c:495
hfs_strcmp+0x117/0x190 fs/hfs/string.c:84
__hfs_brec_find+0x213/0x5c0 fs/hfs/bfind.c:75
hfs_brec_find+0x276/0x520 fs/hfs/bfind.c:138
hfs_write_inode+0x34c/0xb40 fs/hfs/inode.c:462
write_inode fs/fs-writeback.c:1440 [inline]
If the input inode of hfs_write_inode() is incorrect:
struct inode
struct hfs_inode_info
struct hfs_cat_key
struct hfs_name
u8 len # len is greater than HFS_NAMELEN(31) which is the
maximum length of an HFS filename
OOB read occurred:
hfs_write_inode()
hfs_brec_find()
__hfs_brec_find()
hfs_cat_keycmp()
hfs_strcmp() # OOB read occurred due to len is too large
Fix this by adding a Check on len in hfs_write_inode() before calling
hfs_brec_find(). |
| In the Linux kernel, the following vulnerability has been resolved:
blk-throttle: prevent overflow while calculating wait time
There is a problem found by code review in tg_with_in_bps_limit() that
'bps_limit * jiffy_elapsed_rnd' might overflow. Fix the problem by
calling mul_u64_u64_div_u64() instead. |
