| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
mlx5: fix skb leak while fifo resync and push
During ptp resync operation SKBs were poped from the fifo but were never
freed neither by napi_consume nor by dev_kfree_skb_any. Add call to
napi_consume_skb to properly free SKBs.
Another leak was happening because mlx5e_skb_fifo_has_room() had an error
in the check. Comparing free running counters works well unless C promotes
the types to something wider than the counter. In this case counters are
u16 but the result of the substraction is promouted to int and it causes
wrong result (negative value) of the check when producer have already
overlapped but consumer haven't yet. Explicit cast to u16 fixes the issue. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm/a6xx: Fix kvzalloc vs state_kcalloc usage
adreno_show_object() is a trap! It will re-allocate the pointer it is
passed on first call, when the data is ascii85 encoded, using kvmalloc/
kvfree(). Which means the data *passed* to it must be kvmalloc'd, ie.
we cannot use the state_kcalloc() helper.
This partially reverts commit ec8f1813bf8d ("drm/msm/a6xx: Replace
kcalloc() with kvzalloc()"), but adds the missing kvfree() to fix the
memory leak that was present previously. And adds a warning comment.
Patchwork: https://patchwork.freedesktop.org/patch/507014/ |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: mpi3mr: Fix missing mrioc->evtack_cmds initialization
Commit c1af985d27da ("scsi: mpi3mr: Add Event acknowledgment logic")
introduced an array mrioc->evtack_cmds but initialization of the array
elements was missed. They are just zero cleared. The function
mpi3mr_complete_evt_ack() refers host_tag field of the elements. Due to the
zero value of the host_tag field, the function calls clear_bit() for
mrico->evtack_cmds_bitmap with wrong bit index. This results in memory
access to invalid address and "BUG: KASAN: use-after-free". This BUG was
observed at eHBA-9600 firmware update to version 8.3.1.0. To fix it, add
the missing initialization of mrioc->evtack_cmds. |
| In the Linux kernel, the following vulnerability has been resolved:
hwrng: amd - Fix PCI device refcount leak
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() for the normal and error path. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SOF: avoid a NULL dereference with unsupported widgets
If an IPC4 topology contains an unsupported widget, its .module_info
field won't be set, then sof_ipc4_route_setup() will cause a kernel
Oops trying to dereference it. Add a check for such cases. |
| In the Linux kernel, the following vulnerability has been resolved:
net: libwx: fix memory leak in wx_setup_rx_resources
When wx_alloc_page_pool() failed in wx_setup_rx_resources(), it doesn't
release DMA buffer. Add dma_free_coherent() in the error path to release
the DMA buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: raa215300: Fix resource leak in case of error
The clk_register_clkdev() allocates memory by calling vclkdev_alloc() and
this memory is not freed in the error path. Similarly, resources allocated
by clk_register_fixed_rate() are not freed in the error path.
Fix these issues by using devm_clk_hw_register_fixed_rate() and
devm_clk_hw_register_clkdev().
After this, the static variable clk is not needed. Replace it withÂ
local variable hw in probe() and drop calling clk_unregister_fixed_rate()
from raa215300_rtc_unregister_device(). |
| In the Linux kernel, the following vulnerability has been resolved:
blk-mq: fix tags leak when shrink nr_hw_queues
Although we don't need to realloc set->tags[] when shrink nr_hw_queues,
we need to free them. Or these tags will be leaked.
How to reproduce:
1. mount -t configfs configfs /mnt
2. modprobe null_blk nr_devices=0 submit_queues=8
3. mkdir /mnt/nullb/nullb0
4. echo 1 > /mnt/nullb/nullb0/power
5. echo 4 > /mnt/nullb/nullb0/submit_queues
6. rmdir /mnt/nullb/nullb0
In step 4, will alloc 9 tags (8 submit queues and 1 poll queue), then
in step 5, new_nr_hw_queues = 5 (4 submit queues and 1 poll queue).
At last in step 6, only these 5 tags are freed, the other 4 tags leaked. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: Fix qmi_msg_handler data structure initialization
qmi_msg_handler is required to be null terminated by QMI module.
There might be a case where a handler for a msg id is not present in the
handlers array which can lead to infinite loop while searching the handler
and therefore out of bound access in qmi_invoke_handler().
Hence update the initialization in qmi_msg_handler data structure.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
serial: 8250: Fix oops for port->pm on uart_change_pm()
Unloading a hardware specific 8250 driver can produce error "Unable to
handle kernel paging request at virtual address" about ten seconds after
unloading the driver. This happens on uart_hangup() calling
uart_change_pm().
Turns out commit 04e82793f068 ("serial: 8250: Reinit port->pm on port
specific driver unbind") was only a partial fix. If the hardware specific
driver has initialized port->pm function, we need to clear port->pm too.
Just reinitializing port->ops does not do this. Otherwise serial8250_pm()
will call port->pm() instead of serial8250_do_pm(). |
| In the Linux kernel, the following vulnerability has been resolved:
ARM: OMAP2+: Fix memory leak in realtime_counter_init()
The "sys_clk" resource is malloced by clk_get(),
it is not released when the function return. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: ets: Always remove class from active list before deleting in ets_qdisc_change
zdi-disclosures@trendmicro.com says:
The vulnerability is a race condition between `ets_qdisc_dequeue` and
`ets_qdisc_change`. It leads to UAF on `struct Qdisc` object.
Attacker requires the capability to create new user and network namespace
in order to trigger the bug.
See my additional commentary at the end of the analysis.
Analysis:
static int ets_qdisc_change(struct Qdisc *sch, struct nlattr *opt,
struct netlink_ext_ack *extack)
{
...
// (1) this lock is preventing .change handler (`ets_qdisc_change`)
//to race with .dequeue handler (`ets_qdisc_dequeue`)
sch_tree_lock(sch);
for (i = nbands; i < oldbands; i++) {
if (i >= q->nstrict && q->classes[i].qdisc->q.qlen)
list_del_init(&q->classes[i].alist);
qdisc_purge_queue(q->classes[i].qdisc);
}
WRITE_ONCE(q->nbands, nbands);
for (i = nstrict; i < q->nstrict; i++) {
if (q->classes[i].qdisc->q.qlen) {
// (2) the class is added to the q->active
list_add_tail(&q->classes[i].alist, &q->active);
q->classes[i].deficit = quanta[i];
}
}
WRITE_ONCE(q->nstrict, nstrict);
memcpy(q->prio2band, priomap, sizeof(priomap));
for (i = 0; i < q->nbands; i++)
WRITE_ONCE(q->classes[i].quantum, quanta[i]);
for (i = oldbands; i < q->nbands; i++) {
q->classes[i].qdisc = queues[i];
if (q->classes[i].qdisc != &noop_qdisc)
qdisc_hash_add(q->classes[i].qdisc, true);
}
// (3) the qdisc is unlocked, now dequeue can be called in parallel
// to the rest of .change handler
sch_tree_unlock(sch);
ets_offload_change(sch);
for (i = q->nbands; i < oldbands; i++) {
// (4) we're reducing the refcount for our class's qdisc and
// freeing it
qdisc_put(q->classes[i].qdisc);
// (5) If we call .dequeue between (4) and (5), we will have
// a strong UAF and we can control RIP
q->classes[i].qdisc = NULL;
WRITE_ONCE(q->classes[i].quantum, 0);
q->classes[i].deficit = 0;
gnet_stats_basic_sync_init(&q->classes[i].bstats);
memset(&q->classes[i].qstats, 0, sizeof(q->classes[i].qstats));
}
return 0;
}
Comment:
This happens because some of the classes have their qdiscs assigned to
NULL, but remain in the active list. This commit fixes this issue by always
removing the class from the active list before deleting and freeing its
associated qdisc
Reproducer Steps
(trimmed version of what was sent by zdi-disclosures@trendmicro.com)
```
DEV="${DEV:-lo}"
ROOT_HANDLE="${ROOT_HANDLE:-1:}"
BAND2_HANDLE="${BAND2_HANDLE:-20:}" # child under 1:2
PING_BYTES="${PING_BYTES:-48}"
PING_COUNT="${PING_COUNT:-200000}"
PING_DST="${PING_DST:-127.0.0.1}"
SLOW_TBF_RATE="${SLOW_TBF_RATE:-8bit}"
SLOW_TBF_BURST="${SLOW_TBF_BURST:-100b}"
SLOW_TBF_LAT="${SLOW_TBF_LAT:-1s}"
cleanup() {
tc qdisc del dev "$DEV" root 2>/dev/null
}
trap cleanup EXIT
ip link set "$DEV" up
tc qdisc del dev "$DEV" root 2>/dev/null || true
tc qdisc add dev "$DEV" root handle "$ROOT_HANDLE" ets bands 2 strict 2
tc qdisc add dev "$DEV" parent 1:2 handle "$BAND2_HANDLE" \
tbf rate "$SLOW_TBF_RATE" burst "$SLOW_TBF_BURST" latency "$SLOW_TBF_LAT"
tc filter add dev "$DEV" parent 1: protocol all prio 1 u32 match u32 0 0 flowid 1:2
tc -s qdisc ls dev $DEV
ping -I "$DEV" -f -c "$PING_COUNT" -s "$PING_BYTES" -W 0.001 "$PING_DST" \
>/dev/null 2>&1 &
tc qdisc change dev "$DEV" root handle "$ROOT_HANDLE" ets bands 2 strict 0
tc qdisc change dev "$DEV" root handle "$ROOT_HANDLE" ets bands 2 strict 2
tc -s qdisc ls dev $DEV
tc qdisc del dev "$DEV" parent
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: Revert "scsi: qla2xxx: Perform lockless command completion in abort path"
This reverts commit 0367076b0817d5c75dfb83001ce7ce5c64d803a9.
The commit being reverted added code to __qla2x00_abort_all_cmds() to
call sp->done() without holding a spinlock. But unlike the older code
below it, this new code failed to check sp->cmd_type and just assumed
TYPE_SRB, which results in a jump to an invalid pointer in target-mode
with TYPE_TGT_CMD:
qla2xxx [0000:65:00.0]-d034:8: qla24xx_do_nack_work create sess success
0000000009f7a79b
qla2xxx [0000:65:00.0]-5003:8: ISP System Error - mbx1=1ff5h mbx2=10h
mbx3=0h mbx4=0h mbx5=191h mbx6=0h mbx7=0h.
qla2xxx [0000:65:00.0]-d01e:8: -> fwdump no buffer
qla2xxx [0000:65:00.0]-f03a:8: qla_target(0): System error async event
0x8002 occurred
qla2xxx [0000:65:00.0]-00af:8: Performing ISP error recovery -
ha=0000000058183fda.
BUG: kernel NULL pointer dereference, address: 0000000000000000
PF: supervisor instruction fetch in kernel mode
PF: error_code(0x0010) - not-present page
PGD 0 P4D 0
Oops: 0010 [#1] SMP
CPU: 2 PID: 9446 Comm: qla2xxx_8_dpc Tainted: G O 6.1.133 #1
Hardware name: Supermicro Super Server/X11SPL-F, BIOS 4.2 12/15/2023
RIP: 0010:0x0
Code: Unable to access opcode bytes at 0xffffffffffffffd6.
RSP: 0018:ffffc90001f93dc8 EFLAGS: 00010206
RAX: 0000000000000282 RBX: 0000000000000355 RCX: ffff88810d16a000
RDX: ffff88810dbadaa8 RSI: 0000000000080000 RDI: ffff888169dc38c0
RBP: ffff888169dc38c0 R08: 0000000000000001 R09: 0000000000000045
R10: ffffffffa034bdf0 R11: 0000000000000000 R12: ffff88810800bb40
R13: 0000000000001aa8 R14: ffff888100136610 R15: ffff8881070f7400
FS: 0000000000000000(0000) GS:ffff88bf80080000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffffffffd6 CR3: 000000010c8ff006 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
? __die+0x4d/0x8b
? page_fault_oops+0x91/0x180
? trace_buffer_unlock_commit_regs+0x38/0x1a0
? exc_page_fault+0x391/0x5e0
? asm_exc_page_fault+0x22/0x30
__qla2x00_abort_all_cmds+0xcb/0x3e0 [qla2xxx_scst]
qla2x00_abort_all_cmds+0x50/0x70 [qla2xxx_scst]
qla2x00_abort_isp_cleanup+0x3b7/0x4b0 [qla2xxx_scst]
qla2x00_abort_isp+0xfd/0x860 [qla2xxx_scst]
qla2x00_do_dpc+0x581/0xa40 [qla2xxx_scst]
kthread+0xa8/0xd0
</TASK>
Then commit 4475afa2646d ("scsi: qla2xxx: Complete command early within
lock") added the spinlock back, because not having the lock caused a
race and a crash. But qla2x00_abort_srb() in the switch below already
checks for qla2x00_chip_is_down() and handles it the same way, so the
code above the switch is now redundant and still buggy in target-mode.
Remove it. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: also call xfrm_state_delete_tunnel at destroy time for states that were never added
In commit b441cf3f8c4b ("xfrm: delete x->tunnel as we delete x"), I
missed the case where state creation fails between full
initialization (->init_state has been called) and being inserted on
the lists.
In this situation, ->init_state has been called, so for IPcomp
tunnels, the fallback tunnel has been created and added onto the
lists, but the user state never gets added, because we fail before
that. The user state doesn't go through __xfrm_state_delete, so we
don't call xfrm_state_delete_tunnel for those states, and we end up
leaking the FB tunnel.
There are several codepaths affected by this: the add/update paths, in
both net/key and xfrm, and the migrate code (xfrm_migrate,
xfrm_state_migrate). A "proper" rollback of the init_state work would
probably be doable in the add/update code, but for migrate it gets
more complicated as multiple states may be involved.
At some point, the new (not-inserted) state will be destroyed, so call
xfrm_state_delete_tunnel during xfrm_state_gc_destroy. Most states
will have their fallback tunnel cleaned up during __xfrm_state_delete,
which solves the issue that b441cf3f8c4b (and other patches before it)
aimed at. All states (including FB tunnels) will be removed from the
lists once xfrm_state_fini has called flush_work(&xfrm_state_gc_work). |
| In the Linux kernel, the following vulnerability has been resolved:
vdpa/vp_vdpa: fix kfree a wrong pointer in vp_vdpa_remove
In vp_vdpa_remove(), the code kfree(&vp_vdpa_mgtdev->mgtdev.id_table) uses
a reference of pointer as the argument of kfree, which is the wrong pointer
and then may hit crash like this:
Unable to handle kernel paging request at virtual address 00ffff003363e30c
Internal error: Oops: 96000004 [#1] SMP
Call trace:
rb_next+0x20/0x5c
ext4_readdir+0x494/0x5c4 [ext4]
iterate_dir+0x168/0x1b4
__se_sys_getdents64+0x68/0x170
__arm64_sys_getdents64+0x24/0x30
el0_svc_common.constprop.0+0x7c/0x1bc
do_el0_svc+0x2c/0x94
el0_svc+0x20/0x30
el0_sync_handler+0xb0/0xb4
el0_sync+0x160/0x180
Code: 54000220 f9400441 b4000161 aa0103e0 (f9400821)
SMP: stopping secondary CPUs
Starting crashdump kernel... |
| In the Linux kernel, the following vulnerability has been resolved:
usb: musb: Fix musb_gadget.c rxstate overflow bug
The usb function device call musb_gadget_queue() adds the passed
request to musb_ep::req_list,If the (request->length > musb_ep->packet_sz)
and (is_buffer_mapped(req) return false),the rxstate() will copy all data
in fifo to request->buf which may cause request->buf out of bounds.
Fix it by add the length check :
fifocnt = min_t(unsigned, request->length - request->actual, fifocnt); |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: core: fix unbalanced of node refcount in regulator_dev_lookup()
I got the the following report:
OF: ERROR: memory leak, expected refcount 1 instead of 2,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /i2c/pmic@62/regulators/exten
In of_get_regulator(), the node is returned from of_parse_phandle()
with refcount incremented, after using it, of_node_put() need be called. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: relax BUG() to ocfs2_error() in __ocfs2_move_extent()
In '__ocfs2_move_extent()', relax 'BUG()' to 'ocfs2_error()' just
to avoid crashing the whole kernel due to a filesystem corruption. |
| In the Linux kernel, the following vulnerability has been resolved:
net: core: prevent NULL deref in generic_hwtstamp_ioctl_lower()
The ethtool tsconfig Netlink path can trigger a null pointer
dereference. A call chain such as:
tsconfig_prepare_data() ->
dev_get_hwtstamp_phylib() ->
vlan_hwtstamp_get() ->
generic_hwtstamp_get_lower() ->
generic_hwtstamp_ioctl_lower()
results in generic_hwtstamp_ioctl_lower() being called with
kernel_cfg->ifr as NULL.
The generic_hwtstamp_ioctl_lower() function does not expect
a NULL ifr and dereferences it, leading to a system crash.
Fix this by adding a NULL check for kernel_cfg->ifr in
generic_hwtstamp_ioctl_lower(). If ifr is NULL, return -EINVAL. |
| In the Linux kernel, the following vulnerability has been resolved:
nios2: ensure that memblock.current_limit is set when setting pfn limits
On nios2, with CONFIG_FLATMEM set, the kernel relies on
memblock_get_current_limit() to determine the limits of mem_map, in
particular for max_low_pfn.
Unfortunately, memblock.current_limit is only default initialized to
MEMBLOCK_ALLOC_ANYWHERE at this point of the bootup, potentially leading
to situations where max_low_pfn can erroneously exceed the value of
max_pfn and, thus, the valid range of available DRAM.
This can in turn cause kernel-level paging failures, e.g.:
[ 76.900000] Unable to handle kernel paging request at virtual address 20303000
[ 76.900000] ea = c0080890, ra = c000462c, cause = 14
[ 76.900000] Kernel panic - not syncing: Oops
[ 76.900000] ---[ end Kernel panic - not syncing: Oops ]---
This patch fixes this by pre-calculating memblock.current_limit
based on the upper limits of the available memory ranges via
adjust_lowmem_bounds, a simplified version of the equivalent
implementation within the arm architecture. |
