| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/srpt: Fix a use-after-free
Change the LIO port members inside struct srpt_port from regular members
into pointers. Allocate the LIO port data structures from inside
srpt_make_tport() and free these from inside srpt_make_tport(). Keep
struct srpt_device as long as either an RDMA port or a LIO target port is
associated with it. This patch decouples the lifetime of struct srpt_port
(controlled by the RDMA core) and struct srpt_port_id (controlled by LIO).
This patch fixes the following KASAN complaint:
BUG: KASAN: use-after-free in srpt_enable_tpg+0x31/0x70 [ib_srpt]
Read of size 8 at addr ffff888141cc34b8 by task check/5093
Call Trace:
<TASK>
show_stack+0x4e/0x53
dump_stack_lvl+0x51/0x66
print_address_description.constprop.0.cold+0xea/0x41e
print_report.cold+0x90/0x205
kasan_report+0xb9/0xf0
__asan_load8+0x69/0x90
srpt_enable_tpg+0x31/0x70 [ib_srpt]
target_fabric_tpg_base_enable_store+0xe2/0x140 [target_core_mod]
configfs_write_iter+0x18b/0x210
new_sync_write+0x1f2/0x2f0
vfs_write+0x3e3/0x540
ksys_write+0xbb/0x140
__x64_sys_write+0x42/0x50
do_syscall_64+0x34/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: flowtable: fix stuck flows on cleanup due to pending work
To clear the flow table on flow table free, the following sequence
normally happens in order:
1) gc_step work is stopped to disable any further stats/del requests.
2) All flow table entries are set to teardown state.
3) Run gc_step which will queue HW del work for each flow table entry.
4) Waiting for the above del work to finish (flush).
5) Run gc_step again, deleting all entries from the flow table.
6) Flow table is freed.
But if a flow table entry already has pending HW stats or HW add work
step 3 will not queue HW del work (it will be skipped), step 4 will wait
for the pending add/stats to finish, and step 5 will queue HW del work
which might execute after freeing of the flow table.
To fix the above, this patch flushes the pending work, then it sets the
teardown flag to all flows in the flowtable and it forces a garbage
collector run to queue work to remove the flows from hardware, then it
flushes this new pending work and (finally) it forces another garbage
collector run to remove the entry from the software flowtable.
Stack trace:
[47773.882335] BUG: KASAN: use-after-free in down_read+0x99/0x460
[47773.883634] Write of size 8 at addr ffff888103b45aa8 by task kworker/u20:6/543704
[47773.885634] CPU: 3 PID: 543704 Comm: kworker/u20:6 Not tainted 5.12.0-rc7+ #2
[47773.886745] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009)
[47773.888438] Workqueue: nf_ft_offload_del flow_offload_work_handler [nf_flow_table]
[47773.889727] Call Trace:
[47773.890214] dump_stack+0xbb/0x107
[47773.890818] print_address_description.constprop.0+0x18/0x140
[47773.892990] kasan_report.cold+0x7c/0xd8
[47773.894459] kasan_check_range+0x145/0x1a0
[47773.895174] down_read+0x99/0x460
[47773.899706] nf_flow_offload_tuple+0x24f/0x3c0 [nf_flow_table]
[47773.907137] flow_offload_work_handler+0x72d/0xbe0 [nf_flow_table]
[47773.913372] process_one_work+0x8ac/0x14e0
[47773.921325]
[47773.921325] Allocated by task 592159:
[47773.922031] kasan_save_stack+0x1b/0x40
[47773.922730] __kasan_kmalloc+0x7a/0x90
[47773.923411] tcf_ct_flow_table_get+0x3cb/0x1230 [act_ct]
[47773.924363] tcf_ct_init+0x71c/0x1156 [act_ct]
[47773.925207] tcf_action_init_1+0x45b/0x700
[47773.925987] tcf_action_init+0x453/0x6b0
[47773.926692] tcf_exts_validate+0x3d0/0x600
[47773.927419] fl_change+0x757/0x4a51 [cls_flower]
[47773.928227] tc_new_tfilter+0x89a/0x2070
[47773.936652]
[47773.936652] Freed by task 543704:
[47773.937303] kasan_save_stack+0x1b/0x40
[47773.938039] kasan_set_track+0x1c/0x30
[47773.938731] kasan_set_free_info+0x20/0x30
[47773.939467] __kasan_slab_free+0xe7/0x120
[47773.940194] slab_free_freelist_hook+0x86/0x190
[47773.941038] kfree+0xce/0x3a0
[47773.941644] tcf_ct_flow_table_cleanup_work
Original patch description and stack trace by Paul Blakey. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix locking in rxrpc's sendmsg
Fix three bugs in the rxrpc's sendmsg implementation:
(1) rxrpc_new_client_call() should release the socket lock when returning
an error from rxrpc_get_call_slot().
(2) rxrpc_wait_for_tx_window_intr() will return without the call mutex
held in the event that we're interrupted by a signal whilst waiting
for tx space on the socket or relocking the call mutex afterwards.
Fix this by: (a) moving the unlock/lock of the call mutex up to
rxrpc_send_data() such that the lock is not held around all of
rxrpc_wait_for_tx_window*() and (b) indicating to higher callers
whether we're return with the lock dropped. Note that this means
recvmsg() will not block on this call whilst we're waiting.
(3) After dropping and regaining the call mutex, rxrpc_send_data() needs
to go and recheck the state of the tx_pending buffer and the
tx_total_len check in case we raced with another sendmsg() on the same
call.
Thinking on this some more, it might make sense to have different locks for
sendmsg() and recvmsg(). There's probably no need to make recvmsg() wait
for sendmsg(). It does mean that recvmsg() can return MSG_EOR indicating
that a call is dead before a sendmsg() to that call returns - but that can
currently happen anyway.
Without fix (2), something like the following can be induced:
WARNING: bad unlock balance detected!
5.16.0-rc6-syzkaller #0 Not tainted
-------------------------------------
syz-executor011/3597 is trying to release lock (&call->user_mutex) at:
[<ffffffff885163a3>] rxrpc_do_sendmsg+0xc13/0x1350 net/rxrpc/sendmsg.c:748
but there are no more locks to release!
other info that might help us debug this:
no locks held by syz-executor011/3597.
...
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_unlock_imbalance_bug include/trace/events/lock.h:58 [inline]
__lock_release kernel/locking/lockdep.c:5306 [inline]
lock_release.cold+0x49/0x4e kernel/locking/lockdep.c:5657
__mutex_unlock_slowpath+0x99/0x5e0 kernel/locking/mutex.c:900
rxrpc_do_sendmsg+0xc13/0x1350 net/rxrpc/sendmsg.c:748
rxrpc_sendmsg+0x420/0x630 net/rxrpc/af_rxrpc.c:561
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:724
____sys_sendmsg+0x6e8/0x810 net/socket.c:2409
___sys_sendmsg+0xf3/0x170 net/socket.c:2463
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2492
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
[Thanks to Hawkins Jiawei and Khalid Masum for their attempts to fix this] |
| In the Linux kernel, the following vulnerability has been resolved:
ieee802154/adf7242: defer destroy_workqueue call
There is a possible race condition (use-after-free) like below
(FREE) | (USE)
adf7242_remove | adf7242_channel
cancel_delayed_work_sync |
destroy_workqueue (1) | adf7242_cmd_rx
| mod_delayed_work (2)
|
The root cause for this race is that the upper layer (ieee802154) is
unaware of this detaching event and the function adf7242_channel can
be called without any checks.
To fix this, we can add a flag write at the beginning of adf7242_remove
and add flag check in adf7242_channel. Or we can just defer the
destructive operation like other commit 3e0588c291d6 ("hamradio: defer
ax25 kfree after unregister_netdev") which let the
ieee802154_unregister_hw() to handle the synchronization. This patch
takes the second option.
runs") |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8712: fix use after free bugs
_Read/Write_MACREG callbacks are NULL so the read/write_macreg_hdl()
functions don't do anything except free the "pcmd" pointer. It
results in a use after free. Delete them. |
| In the Linux kernel, the following vulnerability has been resolved:
binder: fix UAF of ref->proc caused by race condition
A transaction of type BINDER_TYPE_WEAK_HANDLE can fail to increment the
reference for a node. In this case, the target proc normally releases
the failed reference upon close as expected. However, if the target is
dying in parallel the call will race with binder_deferred_release(), so
the target could have released all of its references by now leaving the
cleanup of the new failed reference unhandled.
The transaction then ends and the target proc gets released making the
ref->proc now a dangling pointer. Later on, ref->node is closed and we
attempt to take spin_lock(&ref->proc->inner_lock), which leads to the
use-after-free bug reported below. Let's fix this by cleaning up the
failed reference on the spot instead of relying on the target to do so.
==================================================================
BUG: KASAN: use-after-free in _raw_spin_lock+0xa8/0x150
Write of size 4 at addr ffff5ca207094238 by task kworker/1:0/590
CPU: 1 PID: 590 Comm: kworker/1:0 Not tainted 5.19.0-rc8 #10
Hardware name: linux,dummy-virt (DT)
Workqueue: events binder_deferred_func
Call trace:
dump_backtrace.part.0+0x1d0/0x1e0
show_stack+0x18/0x70
dump_stack_lvl+0x68/0x84
print_report+0x2e4/0x61c
kasan_report+0xa4/0x110
kasan_check_range+0xfc/0x1a4
__kasan_check_write+0x3c/0x50
_raw_spin_lock+0xa8/0x150
binder_deferred_func+0x5e0/0x9b0
process_one_work+0x38c/0x5f0
worker_thread+0x9c/0x694
kthread+0x188/0x190
ret_from_fork+0x10/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: Fix UAF in ieee80211_scan_rx()
ieee80211_scan_rx() tries to access scan_req->flags after a
null check, but a UAF is observed when the scan is completed
and __ieee80211_scan_completed() executes, which then calls
cfg80211_scan_done() leading to the freeing of scan_req.
Since scan_req is rcu_dereference()'d, prevent the racing in
__ieee80211_scan_completed() by ensuring that from mac80211's
POV it is no longer accessed from an RCU read critical section
before we call cfg80211_scan_done(). |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: release flow rule object from commit path
No need to postpone this to the commit release path, since no packets
are walking over this object, this is accessed from control plane only.
This helped uncovered UAF triggered by races with the netlink notifier. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Fix use-after-free caused by l2cap_reassemble_sdu
Fix the race condition between the following two flows that run in
parallel:
1. l2cap_reassemble_sdu -> chan->ops->recv (l2cap_sock_recv_cb) ->
__sock_queue_rcv_skb.
2. bt_sock_recvmsg -> skb_recv_datagram, skb_free_datagram.
An SKB can be queued by the first flow and immediately dequeued and
freed by the second flow, therefore the callers of l2cap_reassemble_sdu
can't use the SKB after that function returns. However, some places
continue accessing struct l2cap_ctrl that resides in the SKB's CB for a
short time after l2cap_reassemble_sdu returns, leading to a
use-after-free condition (the stack trace is below, line numbers for
kernel 5.19.8).
Fix it by keeping a local copy of struct l2cap_ctrl.
BUG: KASAN: use-after-free in l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
Read of size 1 at addr ffff88812025f2f0 by task kworker/u17:3/43169
Workqueue: hci0 hci_rx_work [bluetooth]
Call Trace:
<TASK>
dump_stack_lvl (lib/dump_stack.c:107 (discriminator 4))
print_report.cold (mm/kasan/report.c:314 mm/kasan/report.c:429)
? l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
kasan_report (mm/kasan/report.c:162 mm/kasan/report.c:493)
? l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
l2cap_rx (net/bluetooth/l2cap_core.c:7236 net/bluetooth/l2cap_core.c:7271) bluetooth
ret_from_fork (arch/x86/entry/entry_64.S:306)
</TASK>
Allocated by task 43169:
kasan_save_stack (mm/kasan/common.c:39)
__kasan_slab_alloc (mm/kasan/common.c:45 mm/kasan/common.c:436 mm/kasan/common.c:469)
kmem_cache_alloc_node (mm/slab.h:750 mm/slub.c:3243 mm/slub.c:3293)
__alloc_skb (net/core/skbuff.c:414)
l2cap_recv_frag (./include/net/bluetooth/bluetooth.h:425 net/bluetooth/l2cap_core.c:8329) bluetooth
l2cap_recv_acldata (net/bluetooth/l2cap_core.c:8442) bluetooth
hci_rx_work (net/bluetooth/hci_core.c:3642 net/bluetooth/hci_core.c:3832) bluetooth
process_one_work (kernel/workqueue.c:2289)
worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2437)
kthread (kernel/kthread.c:376)
ret_from_fork (arch/x86/entry/entry_64.S:306)
Freed by task 27920:
kasan_save_stack (mm/kasan/common.c:39)
kasan_set_track (mm/kasan/common.c:45)
kasan_set_free_info (mm/kasan/generic.c:372)
____kasan_slab_free (mm/kasan/common.c:368 mm/kasan/common.c:328)
slab_free_freelist_hook (mm/slub.c:1780)
kmem_cache_free (mm/slub.c:3536 mm/slub.c:3553)
skb_free_datagram (./include/net/sock.h:1578 ./include/net/sock.h:1639 net/core/datagram.c:323)
bt_sock_recvmsg (net/bluetooth/af_bluetooth.c:295) bluetooth
l2cap_sock_recvmsg (net/bluetooth/l2cap_sock.c:1212) bluetooth
sock_read_iter (net/socket.c:1087)
new_sync_read (./include/linux/fs.h:2052 fs/read_write.c:401)
vfs_read (fs/read_write.c:482)
ksys_read (fs/read_write.c:620)
do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: zfcp: Fix double free of FSF request when qdio send fails
We used to use the wrong type of integer in 'zfcp_fsf_req_send()' to cache
the FSF request ID when sending a new FSF request. This is used in case the
sending fails and we need to remove the request from our internal hash
table again (so we don't keep an invalid reference and use it when we free
the request again).
In 'zfcp_fsf_req_send()' we used to cache the ID as 'int' (signed and 32
bit wide), but the rest of the zfcp code (and the firmware specification)
handles the ID as 'unsigned long'/'u64' (unsigned and 64 bit wide [s390x
ELF ABI]). For one this has the obvious problem that when the ID grows
past 32 bit (this can happen reasonably fast) it is truncated to 32 bit
when storing it in the cache variable and so doesn't match the original ID
anymore. The second less obvious problem is that even when the original ID
has not yet grown past 32 bit, as soon as the 32nd bit is set in the
original ID (0x80000000 = 2'147'483'648) we will have a mismatch when we
cast it back to 'unsigned long'. As the cached variable is of a signed
type, the compiler will choose a sign-extending instruction to load the 32
bit variable into a 64 bit register (e.g.: 'lgf %r11,188(%r15)'). So once
we pass the cached variable into 'zfcp_reqlist_find_rm()' to remove the
request again all the leading zeros will be flipped to ones to extend the
sign and won't match the original ID anymore (this has been observed in
practice).
If we can't successfully remove the request from the hash table again after
'zfcp_qdio_send()' fails (this happens regularly when zfcp cannot notify
the adapter about new work because the adapter is already gone during
e.g. a ChpID toggle) we will end up with a double free. We unconditionally
free the request in the calling function when 'zfcp_fsf_req_send()' fails,
but because the request is still in the hash table we end up with a stale
memory reference, and once the zfcp adapter is either reset during recovery
or shutdown we end up freeing the same memory twice.
The resulting stack traces vary depending on the kernel and have no direct
correlation to the place where the bug occurs. Here are three examples that
have been seen in practice:
list_del corruption. next->prev should be 00000001b9d13800, but was 00000000dead4ead. (next=00000001bd131a00)
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:62!
monitor event: 0040 ilc:2 [#1] PREEMPT SMP
Modules linked in: ...
CPU: 9 PID: 1617 Comm: zfcperp0.0.1740 Kdump: loaded
Hardware name: ...
Krnl PSW : 0704d00180000000 00000003cbeea1f8 (__list_del_entry_valid+0x98/0x140)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:1 PM:0 RI:0 EA:3
Krnl GPRS: 00000000916d12f1 0000000080000000 000000000000006d 00000003cb665cd6
0000000000000001 0000000000000000 0000000000000000 00000000d28d21e8
00000000d3844000 00000380099efd28 00000001bd131a00 00000001b9d13800
00000000d3290100 0000000000000000 00000003cbeea1f4 00000380099efc70
Krnl Code: 00000003cbeea1e8: c020004f68a7 larl %r2,00000003cc8d7336
00000003cbeea1ee: c0e50027fd65 brasl %r14,00000003cc3e9cb8
#00000003cbeea1f4: af000000 mc 0,0
>00000003cbeea1f8: c02000920440 larl %r2,00000003cd12aa78
00000003cbeea1fe: c0e500289c25 brasl %r14,00000003cc3fda48
00000003cbeea204: b9040043 lgr %r4,%r3
00000003cbeea208: b9040051 lgr %r5,%r1
00000003cbeea20c: b9040032 lgr %r3,%r2
Call Trace:
[<00000003cbeea1f8>] __list_del_entry_valid+0x98/0x140
([<00000003cbeea1f4>] __list_del_entry_valid+0x94/0x140)
[<000003ff7ff502fe>] zfcp_fsf_req_dismiss_all+0xde/0x150 [zfcp]
[<000003ff7ff49cd0>] zfcp_erp_strategy_do_action+0x160/0x280 [zfcp]
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ceph: avoid putting the realm twice when decoding snaps fails
When decoding the snaps fails it maybe leaving the 'first_realm'
and 'realm' pointing to the same snaprealm memory. And then it'll
put it twice and could cause random use-after-free, BUG_ON, etc
issues. |
| In the Linux kernel, the following vulnerability has been resolved:
9p: trans_fd/p9_conn_cancel: drop client lock earlier
syzbot reported a double-lock here and we no longer need this
lock after requests have been moved off to local list:
just drop the lock earlier. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: fix use-after-free in ntfs_attr_find()
Patch series "ntfs: fix bugs about Attribute", v2.
This patchset fixes three bugs relative to Attribute in record:
Patch 1 adds a sanity check to ensure that, attrs_offset field in first
mft record loading from disk is within bounds.
Patch 2 moves the ATTR_RECORD's bounds checking earlier, to avoid
dereferencing ATTR_RECORD before checking this ATTR_RECORD is within
bounds.
Patch 3 adds an overflow checking to avoid possible forever loop in
ntfs_attr_find().
Without patch 1 and patch 2, the kernel triggersa KASAN use-after-free
detection as reported by Syzkaller.
Although one of patch 1 or patch 2 can fix this, we still need both of
them. Because patch 1 fixes the root cause, and patch 2 not only fixes
the direct cause, but also fixes the potential out-of-bounds bug.
This patch (of 3):
Syzkaller reported use-after-free read as follows:
==================================================================
BUG: KASAN: use-after-free in ntfs_attr_find+0xc02/0xce0 fs/ntfs/attrib.c:597
Read of size 2 at addr ffff88807e352009 by task syz-executor153/3607
[...]
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:317 [inline]
print_report.cold+0x2ba/0x719 mm/kasan/report.c:433
kasan_report+0xb1/0x1e0 mm/kasan/report.c:495
ntfs_attr_find+0xc02/0xce0 fs/ntfs/attrib.c:597
ntfs_attr_lookup+0x1056/0x2070 fs/ntfs/attrib.c:1193
ntfs_read_inode_mount+0x89a/0x2580 fs/ntfs/inode.c:1845
ntfs_fill_super+0x1799/0x9320 fs/ntfs/super.c:2854
mount_bdev+0x34d/0x410 fs/super.c:1400
legacy_get_tree+0x105/0x220 fs/fs_context.c:610
vfs_get_tree+0x89/0x2f0 fs/super.c:1530
do_new_mount fs/namespace.c:3040 [inline]
path_mount+0x1326/0x1e20 fs/namespace.c:3370
do_mount fs/namespace.c:3383 [inline]
__do_sys_mount fs/namespace.c:3591 [inline]
__se_sys_mount fs/namespace.c:3568 [inline]
__x64_sys_mount+0x27f/0x300 fs/namespace.c:3568
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
[...]
</TASK>
The buggy address belongs to the physical page:
page:ffffea0001f8d400 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x7e350
head:ffffea0001f8d400 order:3 compound_mapcount:0 compound_pincount:0
flags: 0xfff00000010200(slab|head|node=0|zone=1|lastcpupid=0x7ff)
raw: 00fff00000010200 0000000000000000 dead000000000122 ffff888011842140
raw: 0000000000000000 0000000000040004 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88807e351f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88807e351f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88807e352000: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff88807e352080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff88807e352100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Kernel will loads $MFT/$DATA's first mft record in
ntfs_read_inode_mount().
Yet the problem is that after loading, kernel doesn't check whether
attrs_offset field is a valid value.
To be more specific, if attrs_offset field is larger than bytes_allocated
field, then it may trigger the out-of-bounds read bug(reported as
use-after-free bug) in ntfs_attr_find(), when kernel tries to access the
corresponding mft record's attribute.
This patch solves it by adding the sanity check between attrs_offset field
and bytes_allocated field, after loading the first mft record. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Fix null pointer dereference after failing to issue FLOGI and PLOGI
If lpfc_issue_els_flogi() fails and returns non-zero status, the node
reference count is decremented to trigger the release of the nodelist
structure. However, if there is a prior registration or dev-loss-evt work
pending, the node may be released prematurely. When dev-loss-evt
completes, the released node is referenced causing a use-after-free null
pointer dereference.
Similarly, when processing non-zero ELS PLOGI completion status in
lpfc_cmpl_els_plogi(), the ndlp flags are checked for a transport
registration before triggering node removal. If dev-loss-evt work is
pending, the node may be released prematurely and a subsequent call to
lpfc_dev_loss_tmo_handler() results in a use after free ndlp dereference.
Add test for pending dev-loss before decrementing the node reference count
for FLOGI, PLOGI, PRLI, and ADISC handling. |
| In the Linux kernel, the following vulnerability has been resolved:
ath10k: skip ath10k_halt during suspend for driver state RESTARTING
Double free crash is observed when FW recovery(caused by wmi
timeout/crash) is followed by immediate suspend event. The FW recovery
is triggered by ath10k_core_restart() which calls driver clean up via
ath10k_halt(). When the suspend event occurs between the FW recovery,
the restart worker thread is put into frozen state until suspend completes.
The suspend event triggers ath10k_stop() which again triggers ath10k_halt()
The double invocation of ath10k_halt() causes ath10k_htt_rx_free() to be
called twice(Note: ath10k_htt_rx_alloc was not called by restart worker
thread because of its frozen state), causing the crash.
To fix this, during the suspend flow, skip call to ath10k_halt() in
ath10k_stop() when the current driver state is ATH10K_STATE_RESTARTING.
Also, for driver state ATH10K_STATE_RESTARTING, call
ath10k_wait_for_suspend() in ath10k_stop(). This is because call to
ath10k_wait_for_suspend() is skipped later in
[ath10k_halt() > ath10k_core_stop()] for the driver state
ATH10K_STATE_RESTARTING.
The frozen restart worker thread will be cancelled during resume when the
device comes out of suspend.
Below is the crash stack for reference:
[ 428.469167] ------------[ cut here ]------------
[ 428.469180] kernel BUG at mm/slub.c:4150!
[ 428.469193] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[ 428.469219] Workqueue: events_unbound async_run_entry_fn
[ 428.469230] RIP: 0010:kfree+0x319/0x31b
[ 428.469241] RSP: 0018:ffffa1fac015fc30 EFLAGS: 00010246
[ 428.469247] RAX: ffffedb10419d108 RBX: ffff8c05262b0000
[ 428.469252] RDX: ffff8c04a8c07000 RSI: 0000000000000000
[ 428.469256] RBP: ffffa1fac015fc78 R08: 0000000000000000
[ 428.469276] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 428.469285] Call Trace:
[ 428.469295] ? dma_free_attrs+0x5f/0x7d
[ 428.469320] ath10k_core_stop+0x5b/0x6f
[ 428.469336] ath10k_halt+0x126/0x177
[ 428.469352] ath10k_stop+0x41/0x7e
[ 428.469387] drv_stop+0x88/0x10e
[ 428.469410] __ieee80211_suspend+0x297/0x411
[ 428.469441] rdev_suspend+0x6e/0xd0
[ 428.469462] wiphy_suspend+0xb1/0x105
[ 428.469483] ? name_show+0x2d/0x2d
[ 428.469490] dpm_run_callback+0x8c/0x126
[ 428.469511] ? name_show+0x2d/0x2d
[ 428.469517] __device_suspend+0x2e7/0x41b
[ 428.469523] async_suspend+0x1f/0x93
[ 428.469529] async_run_entry_fn+0x3d/0xd1
[ 428.469535] process_one_work+0x1b1/0x329
[ 428.469541] worker_thread+0x213/0x372
[ 428.469547] kthread+0x150/0x15f
[ 428.469552] ? pr_cont_work+0x58/0x58
[ 428.469558] ? kthread_blkcg+0x31/0x31
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
mt76: fix tx status related use-after-free race on station removal
There is a small race window where ongoing tx activity can lead to a skb
getting added to the status tracking idr after that idr has already been
cleaned up, which will keep the wcid linked in the status poll list.
Fix this by only adding status skbs if the wcid pointer is still assigned
in dev->wcid, which gets cleared early by mt76_sta_pre_rcu_remove |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btmtksdio: fix use-after-free at btmtksdio_recv_event
We should not access skb buffer data anymore after hci_recv_frame was
called.
[ 39.634809] BUG: KASAN: use-after-free in btmtksdio_recv_event+0x1b0
[ 39.634855] Read of size 1 at addr ffffff80cf28a60d by task kworker
[ 39.634962] Call trace:
[ 39.634974] dump_backtrace+0x0/0x3b8
[ 39.634999] show_stack+0x20/0x2c
[ 39.635016] dump_stack_lvl+0x60/0x78
[ 39.635040] print_address_description+0x70/0x2f0
[ 39.635062] kasan_report+0x154/0x194
[ 39.635079] __asan_report_load1_noabort+0x44/0x50
[ 39.635099] btmtksdio_recv_event+0x1b0/0x1c4
[ 39.635129] btmtksdio_txrx_work+0x6cc/0xac4
[ 39.635157] process_one_work+0x560/0xc5c
[ 39.635177] worker_thread+0x7ec/0xcc0
[ 39.635195] kthread+0x2d0/0x3d0
[ 39.635215] ret_from_fork+0x10/0x20
[ 39.635247] Allocated by task 0:
[ 39.635260] (stack is not available)
[ 39.635281] Freed by task 2392:
[ 39.635295] kasan_save_stack+0x38/0x68
[ 39.635319] kasan_set_track+0x28/0x3c
[ 39.635338] kasan_set_free_info+0x28/0x4c
[ 39.635357] ____kasan_slab_free+0x104/0x150
[ 39.635374] __kasan_slab_free+0x18/0x28
[ 39.635391] slab_free_freelist_hook+0x114/0x248
[ 39.635410] kfree+0xf8/0x2b4
[ 39.635427] skb_free_head+0x58/0x98
[ 39.635447] skb_release_data+0x2f4/0x410
[ 39.635464] skb_release_all+0x50/0x60
[ 39.635481] kfree_skb+0xc8/0x25c
[ 39.635498] hci_event_packet+0x894/0xca4 [bluetooth]
[ 39.635721] hci_rx_work+0x1c8/0x68c [bluetooth]
[ 39.635925] process_one_work+0x560/0xc5c
[ 39.635951] worker_thread+0x7ec/0xcc0
[ 39.635970] kthread+0x2d0/0x3d0
[ 39.635990] ret_from_fork+0x10/0x20
[ 39.636021] The buggy address belongs to the object at ffffff80cf28a600
which belongs to the cache kmalloc-512 of size 512
[ 39.636039] The buggy address is located 13 bytes inside of
512-byte region [ffffff80cf28a600, ffffff80cf28a800) |
| In the Linux kernel, the following vulnerability has been resolved:
bonding: fix missed rcu protection
When removing the rcu_read_lock in bond_ethtool_get_ts_info() as
discussed [1], I didn't notice it could be called via setsockopt,
which doesn't hold rcu lock, as syzbot pointed:
stack backtrace:
CPU: 0 PID: 3599 Comm: syz-executor317 Not tainted 5.18.0-rc5-syzkaller-01392-g01f4685797a5 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
bond_option_active_slave_get_rcu include/net/bonding.h:353 [inline]
bond_ethtool_get_ts_info+0x32c/0x3a0 drivers/net/bonding/bond_main.c:5595
__ethtool_get_ts_info+0x173/0x240 net/ethtool/common.c:554
ethtool_get_phc_vclocks+0x99/0x110 net/ethtool/common.c:568
sock_timestamping_bind_phc net/core/sock.c:869 [inline]
sock_set_timestamping+0x3a3/0x7e0 net/core/sock.c:916
sock_setsockopt+0x543/0x2ec0 net/core/sock.c:1221
__sys_setsockopt+0x55e/0x6a0 net/socket.c:2223
__do_sys_setsockopt net/socket.c:2238 [inline]
__se_sys_setsockopt net/socket.c:2235 [inline]
__x64_sys_setsockopt+0xba/0x150 net/socket.c:2235
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f8902c8eb39
Fix it by adding rcu_read_lock and take a ref on the real_dev.
Since dev_hold() and dev_put() can take NULL these days, we can
skip checking if real_dev exist.
[1] https://lore.kernel.org/netdev/27565.1642742439@famine/ |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix use-after-free in chanctx code
In ieee80211_vif_use_reserved_context(), when we have an
old context and the new context's replace_state is set to
IEEE80211_CHANCTX_REPLACE_NONE, we free the old context
in ieee80211_vif_use_reserved_reassign(). Therefore, we
cannot check the old_ctx anymore, so we should set it to
NULL after this point.
However, since the new_ctx replace state is clearly not
IEEE80211_CHANCTX_REPLACES_OTHER, we're not going to do
anything else in this function and can just return to
avoid accessing the freed old_ctx. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: Fix potential use-after-free in nfsd_file_put()
nfsd_file_put_noref() can free @nf, so don't dereference @nf
immediately upon return from nfsd_file_put_noref(). |
